Jump to content

Recommended Posts

Posted

I have a 2017 suburban lt Z71 midnight edition. I have the black 18 in wheels. Swapping them out for a set of 20s. On stock ride height will 275/65/20 rub at all?

 

IMG_20170314_121746.jpg

Posted

You could even go 55's if you wanted to.  I have wheels and tires at stock ride height from the factory, 275/55/20.  Turn radius is better than my cars, no rubbing.  

Posted (edited)

275/55/20 is the stock 20" tire size so that will have zero diameter increase over the 18" and the stock 265/65/18 tires if you are looking for a larger diameter tire.  The 18" and 20" diameter are 31.7-31.9" average, so we will round that to a 32" diameter tire.   

 

I would say at most without a leveling kit, a 275/60/20 should fit (that's a 33" tire).  275/65/20 is a 34" tire and I would think that would rub.  A 285/55/20 may be too wide and might require some wheel liner trimming at full lock, but the diameter is 32.4" so in between the stock 20" and the 275/60/20. 

 

So ideally, 275/60/20 without a lift or level should work. 

Edited by newdude
  • 4 weeks later...
  • 1 year later...
Posted

Please help with advice, I just switched my stock 18” rims with 275/65-18 tires out for 20’s with 275/60/20 tires on my 2018 z71 Suburban and they rub pretty bad!! 

If I do a 2” leveling kit would that likely resolve my issue with the tire size of 275/60/20’s? Or should I do a tire size of 275/50/20?  

Posted

I find that strange, what offset are the 20s? On OEM wheels my 2016 Suburban with a lot of miles (suspension has definitely settled some) fit the 275/60R20s from my truck without issue. 275/50s would be too small, stock size for the 20 spec'd Suburbans was a 275/55R20.

 

If you have aftermarket wheels the offset it likely your issue, either way get someone in the vehicle and turn the wheels both ways while you're outside to see where it's hitting. You may be able to trim/bend something out of the way or see if going up would help.

 

Here is my 16 with 275/60R20 BFG All Terrains, completely stock suspension with no rubbing.

47544234032_a0e18df63b_k.jpg

46681636855_fd9508c4ab_k.jpg

  • 9 months later...
  • 1 month later...
Posted

I have 285/55/20 Toyos on my 2015 Z71 LTZ.  Had to trim about an inch off the edge of the pass side inner fender wall.  Otherwise, looks rides great.

Posted
On 2/9/2020 at 3:43 PM, Jennifer S said:

Please help with advice, I just switched my stock 18” rims with 275/65-18 tires out for 20’s with 275/60/20 tires on my 2018 z71 Suburban and they rub pretty bad!! 

If I do a 2” leveling kit would that likely resolve my issue with the tire size of 275/60/20’s? Or should I do a tire size of 275/50/20?  

 

275/55R20 will have no issues.

 

What type of wheels are the 20"?  Aftermarket?  OEM?

  • 2 weeks later...
Posted

I have a 16’ Yukon, stock says 275/55/20, i was wondering if 275/65/20 would rub? I checked measurements and I know truck would come up an inch as well, would I have to trim anything I’m debating but I do want it to sit higher then with stock, my RAM truck  is a 1500 two wheel drive and it’s got the 275/65/20 and I don’t have any issues with it rubbing so I thought maybe my Yukon won’t either, thanks in advance for advice 

  • 1 year later...
Posted

I have a 2016 suburban z71 off-road I wanted to know what’s the biggest tire size I can fit?

  • Like 1
Posted
28 minutes ago, Dj Gio said:

I have a 2016 suburban z71 off-road I wanted to know what’s the biggest tire size I can fit?

Just like those guys, easy to run 275-60-20 and if a fresh suspension and or with a level, 275-65-20.  If you want to go wider, search for photos but that's about as tall as you can fit in there.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Those are parts changers. It can get expensive though. I was a mechanic for 30 yrs. My truck has made this noise since new. I really don`t know what it is. It really doesn`t bother me. I`m still in warranty but have not brought it to the dealer.   I`m not buying the oil pump prime thing. Screw the TSB. I believe it`s in the trans pump gears. They rattle when that piss poor ULV oil drains off after a while. I believe those sharp tooth gears, with backlash, can rattle when dry. Not a vane style oil pump. Wonder who`s right? Me, or the TSB?🤔   Maybe I`m wrong?
    • Sounds about right. I miss the days of mechanics lol. 
    • On the PCM side, blue PCM connector, pin 18, solid gray color (no stripe) wire circuit 435.  That is the EGR low circuit which an issue on that line (be it the wiring, the PCM or the EGR valve or system performance) will trigger P0401 when it tests that code.     There is also a VERY old TSB that states to make sure you clear the DTCs ANY time the PCM is unplugged, reprogrammed, or if the EGR valve is unplugged or replaced as the PCM has an auto zero function in the PCM for the EGR pintle data   61-65-59: SMU - SECTION 6E - ENGINE CONTROLS - CLEAR DTC'S - (Nov 25, 1996)   "CLEAR ANY DTCS FROM THE VCM ANYTIME AFTER DOING VCM REPLACEMENT/ PROGRAMMING, TURNING THE IGNITION ON WHILE THE EGR VALVE IS DISCONNECTED, OR REPLACING THE EGR VALVE."   Some diagnostic aid notes in the GM diag on P0401 for a 1995 S10 Blazer:   Diagnostic Aids Notice: In order to prevent further damage if the EGR valve shows signs of excessive heat, check the exhaust system for blockage (possibly a plugged converter) using the procedure found on the restricted exhaust system check. If the exhaust system is restricted, repair the cause; one of which might be an injector which is open due to one of the following reasons: Stuck Grounded driver circuit Check the oil for possible fuel contamination if a stuck open fuel injector is found. Poor connection or damaged harness - Inspect VCM harness connectors for the following conditions: Backed out terminal BL 18 Improper mating Broken locks Improperly formed or damaged terminal Poor terminal to wire connection Damaged harness Intermittent test - If connections and harness check OK, monitor a digital voltmeter connected between terminal BL 18 and ground while moving related connectors and wiring harness. If the failure is induced, the voltage reading will change.
    • maybe get a service manual off ebay?  or check charm.li (website) or subscribe to alldata.com for it?
    • This biggest difference in a HM oil is in contains some  "Seal Conditioner". DEXOS oils and most shelf oils are "Dry" oils which over time harden seals. "Seal Conditioner" is more times than not, an Ester. Addition will soften the seals over time but will not repair one that leaks or has cracked. Esters also provide some cleaning but these HM oils don't contain enough to solve out hard deposits. Just the soft stuff.  Also a function of an Ester.    Ester's are not 'allowed' as a 'co-base" by license. Weird, right?  A certain amount is allowed as an additive. Bunch of game playing is what it is. It's why HM oils don't have a DEXOS approval.    DEXOS is a license 'with' a specification but is not a specification. Never was, never will be. It's GM's slot machine always paying the house. Use what you like.       
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...