Jump to content

Recommended Posts

Posted
Just now, customboss said:

The bearings in the GM 5.3L L84 engine commonly use copper-based alloys for strength, wear resistance, and durability. Specifically, the main and rod bearings typically feature:
•    Copper-Lead Alloy: A traditional bearing material combining copper with lead, offering excellent load-carrying capacity and fatigue resistance.
•    Copper-Tin Alloy: An alloy that enhances strength and wear properties, often used in engine bearings to handle the stresses of internal combustion.
•    Layers or Coatings: These bearings often have layered constructions, with a steel backing for support, a copper or copper alloy intermediate layer for strength, and a soft overlay (like babbitt or a tin alloy) on the surface to provide conformability and embed debris.
In modern GM engines like the L84, the use of copper-based alloy bearings reflects a balance of durability, friction reduction, and compatibility with the engine’s lubrication system, which includes specific synthetic oils recommended for the engine. These alloys help withstand the high loads and temperatures inside the engine while providing good resistance to fatigue and seizure.
Overall, copper is a crucial base metal in these bearing alloys, enabling long-lasting engine performance in the L84 5.3L V8.

Lead has been dropped for EPA requirements 

Posted (edited)

10/21/2025
2023 Kia Sportage
26,416 total miles
5,147 miles on oil OLM at 2%
Oil AMSOIL Signature Series 0w-20 
Kia Oil filter

Sample sent to OA.

Edited by Black02Silverado
punctuation
  • Like 2
Posted

10/24/2025

 

Mitsubishi Mirage G4 (Raven)

3A92 engine. 1.2 liter triple. MPFI

JATCO JFO15E CVT transmission

 

35,000 miles on unit

5,000 miles on the engine oil

2,685 miles on since last trans partial drop and fill

Fuel Shell V Power Nitro + 93

 

3.125 quarts Red Line HP Euro Spec 5W40 + 2 oz RLZDP

AMSOIL EA15K13 oil filter

UOA sample pulled. 

 

2 quarts Red Line Non-Slip CVT fluid (J4)

 

  • Like 2
Posted

'25 Wrangler Sport 3.6

 

1,025 miles on odometer

 

5.0qt 0w20 Pennzoil Platinum

Mopar Oil filter

 

Differentials -  fluid drain/refill; 549 miles since gearset swap from 3.45 to 4.56

3.0qt 75w140 Valvoline SynPower gear oil

  • Like 3
Posted
2 hours ago, KARNUT said:

Odyssey 161K five K oil change Valvoline 5-20 full synthetic. 

Two things I noticed. My oil change indicator said 50 percent but the sticker from valvoline said I had 3K miles to go. I pulled out the receipt sure enough it was 5K miles since my last oil change. Interesting. Their business is changing oil. I guess the 5-20 is more expensive than 0-20 so they up the interval? Anyway there’s no difference in fuel mileage. If anything it’s a little higher.

  • Like 1
  • Thanks 1
  • 4 weeks later...
Posted

278,000 Mile Services

Dizzy

 

11/18/2025

 

2015 Terrain 2.4

1K mile OCI 

 

5 Quarts Mobil 1 Euro 0W40

No filter

  • Like 1
Posted

11/16/25

 

1994 Chevrolet Camaro 3.4, 27,287 miles.

 

4.5 quarts Pennzoil Plat 5w30 and Napa Proformer 21040 filter (ACD PF47's on the way).

 

OCI: 975 miles: 11 years and 1 month. 🧐

 

The change before that was 11/15/2004 at 23,432 miles.

  • Like 1
  • Sad 1
Posted (edited)
2 hours ago, Atlas said:

11/16/25

 

1994 Chevrolet Camaro 3.4, 27,287 miles.

 

4.5 quarts Pennzoil Plat 5w30 and Napa Proformer 21040 filter (ACD PF47's on the way).

 

OCI: 975 miles: 11 years and 1 month. 🧐

 

The change before that was 11/15/2004 at 23,432 miles.

It’s gonna be a good putter for you. 
 

Watch coolant level closely dissimilar metal issues on intake gasket of if I remember correctly. I saw you changed coolant or were about to. 

Edited by customboss
  • Thanks 1
Posted

Wife’s 2011 Genesis sedan 148K oil change at 4K miles. Grease Monkey 5-20 Mobile one. Had a coupon. Stood at the bay and watched. I don’t care I watch. Stop them from adding water in the washer. I add washer anti freeze this time of the year. Went to auto zone for cabin and air filter. Changed there just in case. Mark their sticker in the window from 3K to 5K oil change. This car doesn’t have a minder. Still drives as new presents better than its years. Totally unexpected. 

  • Like 1
  • Thanks 1
Posted
12 minutes ago, KARNUT said:

Wife’s 2011 Genesis sedan 148K oil change at 4K miles. Grease Monkey 5-20 Mobile one. Had a coupon. Stood at the bay and watched. I don’t care I watch. Stop them from adding water in the washer. I add washer anti freeze this time of the year. Went to auto zone for cabin and air filter. Changed there just in case. Mark their sticker in the window from 3K to 5K oil change. This car doesn’t have a minder. Still drives as new presents better than its years. Totally unexpected. 

That’s a great car. 

Posted
9 minutes ago, customboss said:

That’s a great car. 

My wife drives under 10K miles a year. Her car before that was a 2005 Elantra GT my grandson drives now. We started buying Hyundai because of the warranty. This one surprised me. 

  • Like 1
Posted

2006 Honda Rancher - 686 total miles on her. Amsoil Formula 4 stroke, and comically small K&N oil filter. Techron in the tank and cosmoline on the rusty bits underneath. Ready for another winter.IMG_3107.thumb.jpeg.8aa27d0b01f00a24303dd65523bae602.jpegIMG_3102.thumb.jpeg.86ffc360145600209b05d9592c6984d3.jpeg

  • Like 1
  • Thanks 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...