Jump to content

Retrax install

zelmo
 Share

Recommended Posts

zelmo Enthusiast

zelmo

Posted
Posted

I got the RetraxPro ordered and have been reading the installation instructions.  Cover will be put on a 2020 Denali 1500 SB. 

 

The only question I have at this point regards the drain tubes.  There are some plastic plugs at the front of the bed but I am sure that they are going to be too high to work correctly.   Is that correct and if so is there anything that I need to be aware of before I start drilling holes?

cdh7917 Enthusiast

cdh7917

Posted
Posted

While my install is on a 2020 2500HD, perhaps it will help.  I ran into the same issue you're describing in that the rubber plugs in the bed were above the drains on the Retrax storage piece.

 

I picked up some brass reducer barbs from Home Depot to go from 1/2" to 3/8".  Picked up a 10' piece of 3/8" tube too.

 

Reducing to the 3/8" tube allowed me to put the drain hoses through a bed drain hole on each side that is in the floor of the bed, just behind the front wall of the bed. 

 

Pro tip - using a hair dryer to warm up the tubing will help you get it into those holes in the truck bed.  At room temp, the hose is somewhat stiff.

zelmo Enthusiast

zelmo

Posted
  • Author
Posted

At first I didn't want to use those holes so I didn't have an obstruction on the floor, but after thinking about it if that is ever a problem I can just remove them temporarily.

 

Is there a reason you went to the trouble of reducing the tube to fit in the existing holes instead of drilling them out to accept the 1/2" tube?

Bo Evans Enthusiast

Bo Evans

Posted
Posted

Make sure and get your rails tilted outward slightly so that the outside edge sits down nicely on the bed rail.  This will aid in proper drainage...

TVelar Enthusiast

TVelar

Posted
Posted

I used the two existing holes in the bed floor just rear of the cab. Not sure if it was the same 1/2" hose or not, but with a little bit of work the hoses fit in fine. Did not want to drill into a new truck. And honestly if you need to put something in the truck like a sheet of plywood and you know it wont be pouring rain, just pull the hoses out and put them back in after.

cdh7917 Enthusiast

cdh7917

Posted
Posted
22 hours ago, zelmo said:

At first I didn't want to use those holes so I didn't have an obstruction on the floor, but after thinking about it if that is ever a problem I can just remove them temporarily.

 

Is there a reason you went to the trouble of reducing the tube to fit in the existing holes instead of drilling them out to accept the 1/2" tube?

 

Drilling would have been the easier option, but I wasn't too keen on taking a drill bit to a new truck.  Since putting in the Retrax, I have also added the rubber GMC bed mat.  I carefully measured and cut holes in it for the hoses to pass through.

  • 2 months later...
NHM25 Enthusiast

NHM25

Posted
Posted

Odd question but here goes... I live in Phoenix. We haven't gotten rain in over 100 days. How necessary are those drain tubes? I just hate the thought of having to drill and/or obstructing part of the floor and losing more clean space. 

  • 1 year later...
AMRx17 New Member

AMRx17

Posted
Posted
On 5/7/2020 at 8:51 AM, cdh7917 said:

 

Drilling would have been the easier option, but I wasn't too keen on taking a drill bit to a new truck.  Since putting in the Retrax, I have also added the rubber GMC bed mat.  I carefully measured and cut holes in it for the hoses to pass through.

Do you mind sharing a picture? I’m currently in the same situation of not wanting to drill and I also have a bed mat. I want to see how it looks to get an idea!

GETGONE Enthusiast

GETGONE

Posted
Posted

I didn't want to drill either so I did the same thing and got reducer barbs and run the smaller hose through the existing holes. I have the factory spray in liner and I don't want to cause rust enlarging or drilling new holes. The hose with the Retrax is too thick/large to fit into the existing holes. I tried and gave up. I tried to redo the hose and just use the smaller hose and try to stretch it to fit on the Retrax plastic pieces that snap into the bottom of the metal housing. That didn't work out either. For some reason now, I was able to just slip fit the smaller hose inside the Retrax hose then through the holes. I had issues with the hose coming off the Retrax nipple since it is just a slip fit with the brass reducer hanging on it. I didn't have any hose clamps the right size to put on it. I'll have to pick some up or try to find a thinner diameter hose that fits the Retrax nipple that can be shoved through the bed floor holes. This is the only picture I have from the original install and it's hard to see the hoses.

IMG_20210618_003705.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      Howdy folks,   Recently I pulled a heated steering wheel and clock spring out of a 2015 Sierra All Terrain (part numbers coming soon - will have to disassemble), and just installed it on my 2016 Sierra WT (as base model as it gets).   On install, I noticed that I’m missing the connector often tucked behind the dash for the heating element.     No problem… or so I thought.   I used an “Add-A-Fuse” at my heated steering wheel fuse location, which has voltage, but no wires. I ran it to the positive of the heated steering wheel (Violet/White), and took black to ground.   Hooked up the battery, turned the truck on - no heated steering wheel. No button backlights. Was pleased to see that my cruise control was working though.   Read a post suggesting reversing polarity, so I gave it a shot. Violet and White to ground, Black to power.    Aha! Heat! But I seemingly can’t turn it off AND still no backlights on any of the buttons.    Checked all fuses, everything is still in good order. I’m stumped.   Does anyone have any insight? If so, please share!
    • TrueBlue
      Brake Pad Warning Message

      By TrueBlue · Posted

      I'm about 1800 miles into my last oil change, and yesterday a message appeared saying oil life was at 77%. Not sure why it popped up but I think all of these electronics could be susceptible to solar flares or somesuch. I change my oil right at 3K each time, and that was the first time in 10870 miles that message came up. Strange thing is that it showed on the screen at all since I don't drive with that sort of info displayed on the DIC.
    • SwitchBladeSierra
      Heated steering wheel

      By SwitchBladeSierra · Posted

      I’m praying that someone sees this and can help me out… pulled a heated steering wheel and clock spring out of a 2015 Sierra All Terrain, and just installed it on my 2016 Sierra WT (as base model as it gets).   On install, I noticed that I’m missing the connector often tucked behind the dash.     No problem… or so I thought.   I used an “Add-A-Fuse” at my heated steering wheel fuse location, which has voltage, but no wires. I ran it to the positive of the heated steering wheel (Violet/White), and took black to ground.   Hooked up the battery, turned the truck on - no heated steering wheel. No button backlights. Was pleased to see that my cruise control was working though.   Read a post suggesting reversing polarity, so I gave it a shot. Violet and White to ground, Black to power.    Aha! Heat! But can’t turn it off AND still no backlights.   Checked all fuses, everything is still in good order. I’m stumped.   Does anyone have any insight? If so, please share!  
    • Vu1can
      Brake Pad Warning Message

      By Vu1can · Posted

      Checked the pads today and there's plenty of meat on them. If the message keeps coming up, I'll just answer YES that the pads were replaced and wait for the squeal.
    • richard wysong
      p0449, p0446, p0451 Evap codes

      By richard wysong · Posted

      Welcome to the Forum! Always post the code definitions along with the codes. there are over 18000 possible codes, no one remembers them all and most will skip over your post rather than look them up

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...