Jump to content

Recommended Posts

Posted

I have a Brownstone Metallic 2015 Silverado built at the Flint plant in May 2015. The truck has 52,000 miles and has been sometimes driven on gravel roads.  I must have got lucky, my paint looks like new everywhere, not even one rock chip. I have never had a vehicle with a better paint job.

 

Dave

Posted
On 9/9/2020 at 10:08 AM, DeltaTek said:

I’m also having the same issue in the same spot, having the dealer look at it today, if they say no then there should be a class action lawsuit against the company for defective paint. Just saying.

9A8C1290-00AB-4E4B-AFEE-82D1266A8143.jpeg

Let me know what the dealership says. 

Posted
On 9/11/2020 at 1:44 PM, dgstarr63 said:

I have a Brownstone Metallic 2015 Silverado built at the Flint plant in May 2015. The truck has 52,000 miles and has been sometimes driven on gravel roads.  I must have got lucky, my paint looks like new everywhere, not even one rock chip. I have never had a vehicle with a better paint job.

Same year, same colour, same luck. but Sierra built in Mexico.  It is strange why some peel and flake while most don't. Maybe the cause is a result of factors after the vehicle was built.  

  • 7 months later...
Posted

I have a 14 Sierra that’s the same color as yours and the paint is flaking off in the same spot on both rear doors. 

  • 1 month later...
Posted

I have a '14 Sierra and it is doing the same of both doors, the hood from rock chips, and the bed of the truck is peeling like crazy. 

 

It is Metallic Silver. I recommend anyone looking at buying a used '14 Sierra RUN as fast a possible because the paint job of these trucks is horrible. 

 

I have tried to mitigate this the best I can with touch up paint and covering the affected areas to prevent it from spreading but it is only a matter of time before that happens. 

 

I love the truck and mechanically the truck is sound but I am severely disappointed in the GMC paint job. 

Posted

When you try and fix it use the GMC Paint Touch Up. Do NOT use Touch Up Direct as it will ruin the paint and not match. I used TouchUpDirect and then went on top of it with the GMC paint and it looks horrible. It made the paint "wrinkle" up. Here are some pics and maybe you can learn from my mistakes. 

 

truck6.thumb.jpg.457761d42fab28ca839a59461b69b088.jpg

truck5.jpg

truck7.jpg

Posted

I have a 2014 Summit White that is peeling as well. Same spot on both rear doors and dead center of the cab about 2 inches back from the windshield. Several small places on the front end but I have not ruled out rock chips for these.

  • 1 month later...
Posted

Yep, 14 Blue Topaz metallic, Drivers side rear door, same place, starts at the bottom of the window and goes up about 3 inches and a inch wide. I'd say manufacturing/Paint shop problem.

  • 3 weeks later...
Posted
 

Anyone else having issues with the paint peeling off your truck?  My 2014 has started to peel and when I contacted GMC they said it was my problem and refused to help fix it.  The dealership wants $1700 to paint the entire door.  I haven't even owned the truck four years.  Any advice would be greatly appreciated.

GMC1.jpg

GMC3.jpg

GMC2.jpg

GMC.jpg

I have a 2014 Sierra that has this same problem, same spot. I called and was told they couldn’t do anything about it. 
Apparently, their is an issue with this model in that area of the vehicle. I am totally disappointed as I purchased new and paid extra 1,000 for this color.

Posted

Exactly the same thing happening to me.  Drivers side door- same spot.  Not sure what I'm gonna do.

  • 2 weeks later...
Posted

Dealership told me it wasn’t their fault and told me to go to their service department to get an estimate. Painter at the service department told me it’s an e-coat issue that doesn’t allow the paint to bond correctly. 
 

Same issue on my door. Now seeing it on the hood and around the front windshield. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined
  • Who's Online   6 Members, 0 Anonymous, 1,391 Guests (See full list)


  • Latest Articles

  • Posts

    • I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed. Why not updates as well, especially since some of those can be safety related also?
    • That's good to know, but I don't think I'll even be running them under 45 in the rear  unless it's on the sand or something but will only be for a short distance anyways!    I didn't read all the instructions in the booklet yet, but do you know let's say I set the rear psi on the placard to 45, will the warning light come on soon as it drops under 45 or is there a percentage it has to drop from the set value before the warning light is triggered?
    • That's bad.  Like, its probably destroying the stub axle the CV slides into.   Do you have a proper lift installed with differential lowering brackets?  Did you install AT4/Trail Boss factory CV axles?  
    • Hot? New Jersey? Today? I was working on my old 2000 Silverado 1500 today. Believe me, it was boiling hot today. As it has been.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...