Jump to content

Antenna relocation while keeping decent reception range

reardiff
 Share

Recommended Posts

reardiff Enthusiast

reardiff

Posted
Posted

Looking for any input or what others have done for antenna replacements. My current long one is not only ugly but is now coming unraveled since i clipped the top off a few inches to not hit the garage opening.  From reading a ton about this topic there seems to be two options, either buy an aftermarket short (5 - 6 inch) or re-route the current one under the hood.  Looking for any advice on how to shorten or preferably visually eliminate the stock antenna while keeping as much reception range as possible (FM only).  Both seem to have reduced signal range but looking to minimize that as much as possible.

 

I've seen plenty of 'How To' videos of routing the stock antenna under the hood but what if I added extra antenna wire and went down the side in multiple passes or down and across the front?  Would that help with reception range at all?   Anyone have a short aftermarket antenna they have good luck with?

 

royalkangaroo Enthusiast

royalkangaroo

Posted
Posted

I can’t speak to completely removing the antenna, however I replaced mine with a 13”

https://www.amazon.com/AntennaMastsRus-Compatible-2006-2019-Guaranteed-Engineered/dp/B00SLNED0G/ref=mp_s_a_1_3?dchild=1&keywords=antennamastsrus&qid=1609854383&sr=8-3&th=1&psc=1

I also listen to satellite radio 99% of the time, but the FM reception sounds about the same as the long stock one.

A friend of mine has a 4” on his truck and it doesn’t look right to me, so I went with one a little longer.

03c425bb0c51c029c29c308ce2a1c078.jpg


Sent from my iPhone using Tapatalk

Eddie 70 Senior Enthusiast

Eddie 70

Posted
Posted

Go to the junkyard and find you one that does not have the wire wrapped on the mast. Cut it down to your preferred height and put a small vacuum cap on it to finish it. I did this to my 02 Z06 years ago. I cut mine down to 6 inch height. Did not affect the radio reception in that car. The radio reception is so poor in these trucks to begin with, I don't know if you would know the difference.

flyingfool Senior Enthusiast

flyingfool

Posted
Posted
2 hours ago, royalkangaroo said:

I can’t speak to completely removing the antenna, however I replaced mine with a 13”

https://www.amazon.com/AntennaMastsRus-Compatible-2006-2019-Guaranteed-Engineered/dp/B00SLNED0G/ref=mp_s_a_1_3?dchild=1&keywords=antennamastsrus&qid=1609854383&sr=8-3&th=1&psc=1

I also listen to satellite radio 99% of the time, but the FM reception sounds about the same as the long stock one.

A friend of mine has a 4” on his truck and it doesn’t look right to me, so I went with one a little longer.

03c425bb0c51c029c29c308ce2a1c078.jpg


Sent from my iPhone using Tapatalk

i thought the flagpole was your antenna from the picture.. lol

flyingfool Senior Enthusiast

flyingfool

Posted
Posted
20 hours ago, reardiff said:

Looking for any input or what others have done for antenna replacements. My current long one is not only ugly but is now coming unraveled since i clipped the top off a few inches to not hit the garage opening.  From reading a ton about this topic there seems to be two options, either buy an aftermarket short (5 - 6 inch) or re-route the current one under the hood.  Looking for any advice on how to shorten or preferably visually eliminate the stock antenna while keeping as much reception range as possible (FM only).  Both seem to have reduced signal range but looking to minimize that as much as possible.

 

I've seen plenty of 'How To' videos of routing the stock antenna under the hood but what if I added extra antenna wire and went down the side in multiple passes or down and across the front?  Would that help with reception range at all?   Anyone have a short aftermarket antenna they have good luck with?

 

correct me if i'm wrong but does the radio on our truck still use a coax cable for input from the antenna?

 

you can always get a cb mount for the rear bed and run new coax to the relocated antenna.  the wire wrapped around the ant is apart of the antennas design performance.  it's an upgraded design over the older styles.

 

one could try cutting down a cb ant, to 1/2 or 1/4wave, or you can chop down an older junk yard unit

KJS Sullivan Enthusiast

KJS Sullivan

Posted
Posted
I can’t speak to completely removing the antenna, however I replaced mine with a 13”

https://www.amazon.com/AntennaMastsRus-Compatible-2006-2019-Guaranteed-Engineered/dp/B00SLNED0G/ref=mp_s_a_1_3?dchild=1&keywords=antennamastsrus&qid=1609854383&sr=8-3&th=1&psc=1

I also listen to satellite radio 99% of the time, but the FM reception sounds about the same as the long stock one.

A friend of mine has a 4” on his truck and it doesn’t look right to me, so I went with one a little longer.

03c425bb0c51c029c29c308ce2a1c078.jpg


Sent from my iPhone using Tapatalk
That one is quite a bit longer with the American flag on top LOL

Sent from my SM-N986U using Tapatalk

royalkangaroo Enthusiast

royalkangaroo

Posted
Posted
That one is quite a bit longer with the American flag on top LOL

Sent from my SM-N986U using Tapatalk


Yes, but the reception is incredible, haha!


Sent from my iPhone using Tapatalk
  • Like 1
reardiff Enthusiast

reardiff

Posted
  • Author
Posted
4 hours ago, royalkangaroo said:

I can’t speak to completely removing the antenna, however I replaced mine with a 13”

https://www.amazon.com/AntennaMastsRus-Compatible-2006-2019-Guaranteed-Engineered/dp/B00SLNED0G/ref=mp_s_a_1_3?dchild=1&keywords=antennamastsrus&qid=1609854383&sr=8-3&th=1&psc=1
I

 

The link above looks like worth trying, and the price is right.  However it says for the best reception use the short  6 3/4 antenna with description below. 

  • UNMATCHED RECEPTION / PROMISED PERFORMANCE - Our 6 3/4" German Engineered Antenna uses choice quality materials, including a highly conductive Internal Copper Coil. While most short antennas are constructed of aluminum or steel, our copper coil is up to 85% more conductive allowing it to pull in stations most short antennas simply dream of. Simple Science, Real Results. If you're not 100% satisfied with performance, return your antenna for a full refund!

What I'm trying to figure out is how can an antenna half the size get better reception than the taller one?  And if it really is using copper coil with 85% more conductively why not use this in the 13 inch one?  Seems a bit gimmick to me, but I'll likely still buy one, just trying to decide which one.  Cant' decide if it looks better with the shorter 6 3/4 or 13 inch?

reardiff Enthusiast

reardiff

Posted
  • Author
Posted (edited)

Ended up getting the 17 inch All Terrain, still quite a bit shorter than stock, but hoping may have a little better reception than the shorter ones. The 6 3/4 just seemed awkward looking being so short.   Had good reviews and had a 9/10 on the reception comparison to the others.  Will post back on reception range after it's installed.

Edited by reardiff
royalkangaroo Enthusiast

royalkangaroo

Posted
Posted
 
The link above looks like worth trying, and the price is right.  However it says for the best reception use the short  6 3/4 antenna with description below. 
  • UNMATCHED RECEPTION / PROMISED PERFORMANCE - Our 6 3/4" German Engineered Antenna uses choice quality materials, including a highly conductive Internal Copper Coil. While most short antennas are constructed of aluminum or steel, our copper coil is up to 85% more conductive allowing it to pull in stations most short antennas simply dream of. Simple Science, Real Results. If you're not 100% satisfied with performance, return your antenna for a full refund!
What I'm trying to figure out is how can an antenna half the size get better reception than the taller one?  And if it really is using copper coil with 85% more conductively why not use this in the 13 inch one?  Seems a bit gimmick to me, but I'll likely still buy one, just trying to decide which one.  Cant' decide if it looks better with the shorter 6 3/4 or 13 inch?

Order both, see which one you prefer, send one back..


Sent from my iPhone using Tapatalk
jagabom (Esquire) Enthusiast

jagabom (Esquire)

Posted
Posted
On 1/5/2021 at 7:37 AM, royalkangaroo said:

I can’t speak to completely removing the antenna, however I replaced mine with a 13”

https://www.amazon.com/AntennaMastsRus-Compatible-2006-2019-Guaranteed-Engineered/dp/B00SLNED0G/ref=mp_s_a_1_3?dchild=1&keywords=antennamastsrus&qid=1609854383&sr=8-3&th=1&psc=1

I also listen to satellite radio 99% of the time, but the FM reception sounds about the same as the long stock one.

A friend of mine has a 4” on his truck and it doesn’t look right to me, so I went with one a little longer.

03c425bb0c51c029c29c308ce2a1c078.jpg


Sent from my iPhone using Tapatalk

On 1st look I thought that was a massive flag on the antenna. 

Jim

  • Like 1
Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted (edited)

On my 15, I relocated my antenna under the right fender, reception was almost crap.  Since I don't listen to AM/FM, I just removed the mast completely, and sold the mast.  I'm trying to find time to install a couple hidden antennas on my truck, in case I ever change my mind.  I'll load some pictures for both trucks, after I get home tonight.

image.png.876f3bc49ace55651b29c1f22857bb61.png

Edited by Ravenkeeper
Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted

 

 

I've gotten a few of my mods from Waymon.  He had a detailed write-up on his antenna relocation.

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      The Peckish Synapse

      By Atlas · Posted

      There's some truth to the above, but also, she's selling fullsize trucks and bread/butter CUV's like hotcakes, meanwhile, extracting GM's pickups from the deep discounting sales game.   GM's stock has held its own during her tenure, and the more recent buybacks are delivering cash back to investors and signal confidence in their direction forward. Even with the EV losses.   GM is an example of a modern publicly traded company. The #1 goal of any publicly traded company is to deliver the most value possible to shareholders. Despite being a car company, building the best car isn't GM's path to delivering maximum shareholder value.   McDonalds doesn't make the best burger, or the best coffee.   I've mentioned in another thread, I really don't / won't ever understand Cadillac or Buick in a modern context. Both brands are completely dead to me. I'll cede that the Escalade is a nice SUV, but the brand and nameplate mean nothing to me, and GM will never persuade me to pay north of $170k for a gussied-up Tahoe or Burb. Other people don't mind doing that and that's their purview.   The C8 shares absolutely nothing in common with any other current Chevrolet or Corvette on the market. Since its introduction 8 years ago, it's developed quite the following. It did what other Corvettes couldn't do: reduce the average age of its buyer. GM has something there, and I see them investing in the car. They'd better not mess that up.   We've successfully derailed Grumpy's thread again, but I think this one is meant to be more of a random thought thread so a little wandering is probably OK.
    • Tyler Gibbs
      2027 GMC Sierra: Official Discussion

      By Tyler Gibbs · Posted

      Sliding doors ftw   Also, Sienna ftw as well.  The in-laws got a 2024-2025 recently when their 2019 sienna was totaled due to a deer back in June.  They've been getting 38-40mpg on the 65mph highway they live on.
    • xdieselmechanic
      07 yukon xl 6.2 stalls at hot idle and wont restart

      By xdieselmechanic · Posted

      Forgot to mention that this started after changing the oil I use mobile 1 full syn with mobile one filter but I did add pro lube additive and was the first time doing so and is making me wonder just can't see why that would matter
    • xdieselmechanic
      07 yukon xl 6.2 stalls at hot idle and wont restart

      By xdieselmechanic · Posted

      I apologize for long post put going to try to explain everything. Parts replaced so far: Cam sensor Crank sensor Cam phaser valve Cam phaser solenoid Fuel pump Maf 1 injector Pcm Pdm   So about 2 weeks ago coming off the highway my 2007 yukon xl with the 6.2 stalled and would restart. Had unit towed back to house and I messed around with relays and unit started. Drove it the next day and same thing. Had it towed again. Scanned unit and had code p0300 with misfire data showing mainly cylinder 7 but I know that won't cause a no start. Measure fuel pressure and found only 42 psi replaced pump to have unit stall again and not restart. This time I stayed on back roads and just waited for it to restart about 30 to 60 min. During this time I found I have no injector pulse but have good power at injectors. Started unplugging 1 injector at a time and found when unplugging cylinder 7 pulse came back so i changed injecto and same issue. Turns out unit just happen to ready to start at that time. Scanned into unit and found no reason for the pcm to take away injector pulse so I replaced the pcm and same issue. I figured timing sesnor controlled the injector pulse so I replaced both sensors and while I had the water pump of i replaced the vvt components while i was in there. Read multiple people have luck chaging the maf for this issue so I changed it. Unit still stalls to this day and loses injector pulse on the ground side when it does. Have noticed watching the live data the pcm is request injectors to fire via injector pwm value. I have redone the ground wires at the left bottom of the block knowing this was the ground location for the pcm but still no luck. I am a mechanic by trade but this is having me pull my hair out. If anyone has something to have me check I will gladly im not much of a parts thrower but im about to load the cannon
    • newdude
      auto mechanical driver's door unlock without pressing button? [2026 Silv. 1500 WT 4WD RC SB 2.7L]

      By newdude · Posted

      Actually.  Wait.   I just re-read your original post.  Are you talking from INSIDE the truck you have to hit unlock?  Or from the key fob?  I had assumed from the key fob.   IF you are talking the inside unlock button, I assume you are shifting to park and its not unlocking the doors?  If so, that is changed via the settings page in the radio.  Go to SETTINGS, then VEHICLE and then it should be under LOCKS or DOOR LOCKS or something like that.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...