Jump to content

VIN # released

crf450r
 Share

Recommended Posts

crf450r Enthusiast

crf450r

Posted
Posted

I am new the forum,  Just ordered a 2021 2500hd,  it has been 18 years since I have ordered a vehicle, I am aware of the delays, but I wanted to know when the VIN# is provided during the process?  I want to put a topper on, and the lead time for that is 4-6 weeks.

 

Thanks

T.O. Enthusiast

T.O.

Posted
Posted

My dealer was able to get my VIN number immediately after it's production week. I am almost certain it hadn't even left the plant on the railcar yet and he had mine. There is a thread on here describing the process with all the 4 digit numbers, but I am not sure what number is associated with the VIN.  

newdude Senior Enthusiast

newdude

Posted
Posted

You won't get a VIN until 3800.

 

Quote

 

• 500, this is a dealer stock order code used to order common vehicles. Please contact your dealer to receive an actual active order number.
• 1100, Preliminary order accepted (This means your dealer has entered your order into their system but does not mean they have the allocation to submit the order to GM yet. Speak with your dealer to verify when they expect to be able to submit your order for production)
• 2000, Order accepted by GM (This means the order has been submitted and accepted by production. You are now on your way.)
• 2030, Order re-edited (if necessary) (This is simply an edit code showing that something on your order has been changed. It does not mean your order has been accepted to production and really does not mean anything beyond your previous status other than a change has been made.)
• 2051, Order changed thru Web (same as above)
• 2500, Order preferenced (This means that the Order has been moved to the stage that parts department is now ready to place the orders for the components that will become your car)
• 3000, Order accepted by production control (This is the response from production to your 2500 status and is when Parts are actually ordered. No further changes can be made to your order once you reach this point.)
• 3100, Order available to sequence (This is more or less an inter-office memo from Parts to Production saying all parts are committed to this build, they are clear to sequence them for the build.)
• 3300, Order scheduled for production (This is the response to the 3100 status where Production is cleared to sequence and schedule the build) TPW usually avaiable
• 3400, Order broadcast (This is when the order is actually loaded onto the production line computers and parts are being staged for the build)
• 3800, Order produced (The vehicle is completed and has rolled off the line. A Vin is now available.)
• 4000, Available to ship (Vehicle is off the line and available to ship)
• 4104, Bailment Invoice (Shipping documents generated)
• 4200, Shipped (Vehicle has been moved by a carrier to another location or destination. If in combination with a 4300 status code then this is transfer to either a vendor for upfitting or to a distribution yard for final transportation.)
• 4300, Intermediate Delivery (In combination with a 4200 this is saying that the vehicle has been transported to a vendor or to a distribution center.)
• 4B00, Bayed (listed anytime a vehicle is sitting parked waiting for next mode of transportation. It can also be this status while in Quality Control)
• 4800 Rail Ramp Unload, end of the line by (if) rail. To be delivered by truck to dealer
• 5000, Delivered to the dealer
• 6000, Delivered to the customer
• 9000, Order Cancelled

 

 

  • Like 2
nards444 Senior Enthusiast

nards444

Posted
Posted

yeah have to know where you are at in the process.  3800 is when you get a vin and for the most part truck should be done.  With that said to get to 3800 for some takes weeks or months.  Once you get to 3800 you can figure about a month to get the truck.

Another JR Senior Enthusiast

Another JR

Posted
Posted (edited)

I was at 3800 with a VIN on 3/8.  My dealer just gave me an ETA of 4/26.  I think the fact that they now have an ETA means it finally actually went to the outgoing shipper after a couple of weeks of moving around Flint.  

Edited by Another JR
TheeSpaniard3500hd Enthusiast

TheeSpaniard3500hd

Posted
Posted

My truck has an eta of 4/28 per the train shipping data page. Truck arrived in Portland on the way to Seattle area on Sunday. It doesn’t seem like it should take a month to delivery when it’s that close. Hoping it arrives sooner. Dealer has been sending almost daily updates of transit progress which I appreciate.


Sent from my iPhone using Tapatalk

Z45 Senior Enthusiast

Z45

Posted
Posted (edited)
6 hours ago, TheeSpaniard3500hd said:

My truck has an eta of 4/28 per the train shipping data page. Truck arrived in Portland on the way to Seattle area on Sunday. It doesn’t seem like it should take a month to delivery when it’s that close. Hoping it arrives sooner. Dealer has been sending almost daily updates of transit progress which I appreciate.


Sent from my iPhone using Tapatalk

Shipping companies are experiencing unprecedented demand,  transit delays and personnel shortages..  I been waiting for weeks to get a replacement door panel for my 16ft garage door and the local installer said its been taking months to get parts that used to take a week at most.    

Some things are just not important in the grand scheme of things and there is no priority to move them. That's just the way it is with the current state of affairs.  Vehicle movements are not high priority.

Edited by elcamino
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Z45
      Fluid Change Questions

      By Z45 · Posted

      I would be surprised if the diff's were not filled (with the cheapest gear lube) at the axle factory before being shipped to GM.  If you ever watched them building trucks they install the axles and all suspension parts with the frame upside down and then turn it over before its time to install the engine.     Too much gear lube in a axle can be worse than not enough especially with a lower quality GL where is get whipped up with entrained air (foam)  weakening its ability to lubricate.        
    • MORSNO
      Oil Consumption

      By MORSNO · Posted

      This is the 6.6 gasser section of the forum, you should either delete or modify your previous post as it is misleading for anyone looking for factual information on their 6.6 gas engine.
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Well....I've done my first intake gasket. Probably wrong, but...we'll see?   Ultra black on the china walls and 1/4" up onto the sides of the intake gaskets. Permatex High Tack (couldn't find Gaskachinch) on the head side of the intake gasket. I read wrong and it says you're supposed to put it on the mating surface of the head, not the gasket. Hoping it's like a PB&J sandwich where it doesn't matter what side the PB goes on so long as there's jelly. That crap is messy/sticky and I got a dab or two on the intake port openings, tried to wipe it off. Hopefully it won't be a big deal and will only aid in sealing.   Per instructions I left the intake (top side) of the gasket dry except for a light smear of RTV around the coolant ports. Wiggling the intake in there was a bear but I had help to free me of surrounding wiring/stuff but I was basically able to set it straight down lined up with the bolt holes.   I did not think to wait until the RTV skinned over but there probably was 5-10 minutes while it sat before installing the intake.   Bolts finger tight first. Then, followed the Chilton's manual pattern to snug them to 15 lb-ft.   Waited a little over an hour, and then did the final torque in sequence again to 35 lb-ft.   Yesterday I replaced the fuel pressure regulator and got my new "nut and bolt kit" (fuel lines) installed. Damn GM used security torx on the spider, which I don't have, so I got scammed at the local HW store for an off-brand security Torx bit set.   The new driver's door mirror arrived yesterday, so, there's a chance this thing could be running and road legal tomorrow? I don't want to get my hopes up.   This will be my first time stabbing a distributor, too. Although, lucky me, someone else marked the old distributor for removal previously, I did see that. (Someone's been here before!!). Engine is still at TDC so it *should* be just a matter of transferring the mark to the new dizzy and rotating it into place.
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      He has his dad’s newer truck he’s put away. He has several old cars he rotates between him and his family. I’ve seen a restored square body and a SS Chevy truck he’s sometimes drives. He did raffle off a new suburban recently. As much as he is watched if he drove new stuff as a rule we’d know it. It would be fine by me. I don’t care what people prefer. I got one more new one in me. I’d rather my wife get one. I can’t get her out of the Genesis. Don’t tell anyone. I want her to get an electric truck. I want to put a generator in the back. Just because. She hasn’t bit yet.
    • Atlas
      2027 GMC Sierra: Official Discussion

      By Atlas · Posted

      Yes, you must have seen my thread on the Blazer. HOT GARBAGE, but I love them anyway. I'm convinced every car guy has a soft sport for an S/T series somewheres. Probably even a Panther too, if I'm being an honest car guy. That doesn't mean they aren't junk. And they definitely don't get better with age. I sometimes play with old cars, but that's by choice. I don't rely on them and they aren't my everyday fleet.   Derek plays the common man on Youtube and that's no doubt where he started. Now he has Youtube money (and Motortrend, etc). You think his crews and his wife ride around in old beaters when they're chasing him and his wrecks across the country? No he's got newer and nicer stuff for that, you'll see glimpses of it in the footage.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...