Jump to content

Sun glare on center console

21AT4NJ

By 21AT4NJ
in Modifications, Wheels & Tires

 Share

Recommended Posts

21AT4NJ New Member

21AT4NJ

Posted
Posted

I can't be the only one with this issue, but when the sun is up, the trim around my center console gives off a nasty glare right into my face. Has anyone solved this issue? I have 5 percent tint all the way around, plus the sun strip. 

A08F33D5-BE27-404D-9119-DAF781586F13.jpeg

Unique_NY Enthusiast

Unique_NY

Posted
Posted

Sounds like a good opportunity to change it to a custom matte paint color or plastidip or something like that?

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted

Not the same vehicle but the same problem. I keep a shop towel handy and just cover it. On the bike I found a black powder coated part to replace the chrome. A wrap would work. 

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted

I can't stand chrome. why do manufacturers put it on the interior of a car of all places? its so hard to remove from interiors because the chrome parts are often so small and difficult to remove, paint, or wrap without damage. for the exact reason you see there, it seem to be a safety hazard! I once drove a Dodge Charger that was probably the worst of all. if the sun was out no matter what direction you were traveling some piece of interior chrome reflected the sun directly into your eyes. it had this big CHARGER badge on the passenger's side dash, all chrome, you'd be seeing spots if that thing caught the sun. then just as you round the corner expecting relief the sun hits the big chrome driver's door handle and now your other eye is blasted...

 

I haven't put much effort into removing the chrome on the interior of my truck, especially because it seems to be a brushed chrome, its not quite as mirror reflective as the exterior stuff. (it still reflects the sun into your eyes just as easily as the mirror chrome though) but I'd look into a vinyl wrap or something to cover it up. no only will it solve this dangerous situation, but it would look so much better.

 

I saw a picture somewhere on this forum of someone who had their interior chrome wrapped in a matte brushed copper vinyl or something similar to that. it looked really good.

Vigilante375 Enthusiast

Vigilante375

Posted
Posted

My Camaro has the exact same issue between 12 and 1 pm.  The chrome on the dash around the gauges will blind you.  I agree that I don't know why they put these crap chrome pieces inside or outside of vehicles.  Chrome should be an extra add on and the default state of a vehicle should be color matched on the outside and brushed chrome or whatever that won't reflect the sun right into your eyes.

 

Best thing to do is get a vinyl wrap and it'll solve the issue.

1454 Enthusiast

1454

Posted
Posted

I had to vinyl wrap mine. It did it twice on the way home my first week of ownership and I remedied that this weekend. 

21AT4NJ New Member

21AT4NJ

Posted
  • Author
Posted
3 hours ago, 1454 said:

I had to vinyl wrap mine. It did it twice on the way home my first week of ownership and I remedied that this weekend. 

How did you vinyl wrap it

1454 Enthusiast

1454

Posted
Posted
15 minutes ago, 21AT4NJ said:

How did you vinyl wrap it

I took a 2  inch wide strip of 3M vinyl and then used a sharp exacto knife to trim the excess. 

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
2 minutes ago, 1454 said:

I took a 2  inch wide strip of 3M vinyl and then used a sharp exacto knife to trim the excess. 

I was thinking of asking for tips since I haven't done this myself yet. did you take any of the pieces off or do the work with them installed? many of the chrome pieces are actually separable from what's around then. the ones around the LCD screen for example are attached with screws and some melted plastic tabs. you'd have to break the tabs, but they should be able to reinstall pretty easily. I'm wondering if all of that is worth the effort to be able to wrap the vinyl around behind the piece to prevent any chrome peeking through or if its possible to do just as good a job without taking things apart. any advice?

could you post some pictures? I'd really like to see how it came out.

 

did you attempt the door handles by any chance? they will be tough due to the shape, I'm wondering if the chrome part of those can be removed somehow so the vinyl can be stretched and wrapped around the back.

gemarsh Senior Enthusiast

gemarsh

Posted
Posted
5 hours ago, kodiakdenali said:

...

 

did you attempt the door handles by any chance? they will be tough due to the shape, I'm wondering if the chrome part of those can be removed somehow so the vinyl can be stretched and wrapped around the back.

3/0 heat shrink tubing works wonders on the handles.

gemarsh Senior Enthusiast

gemarsh

Posted
Posted
15 minutes ago, kodiakdenali said:

Interesting idea, what about the open end though?

Yep, doesn't shrink closed. Yep, shiny handles are black. I tried one of those black rubber caps on the end and shrunk around it, but the handles aren't round and it looked goofier that a half closed end that you don't really see.

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted (edited)

I would need to research a lot more to see what products are out there, but it appears that there at least exists some "end cap" heat shrink tubes, the largest ones here are about 4.5" long, basically a piece of heat shrink but with one end capped off instead of just open. this could be a great solution to the door handles.

 

https://www.amazon.com/Heat-Shrink-End-Cap-Pieces/dp/B00ZYTQ7A4/ref=sr_1_3?dchild=1&keywords=heat%2Bshrink%2Bend%2Bcap&qid=1618499373&sr=8-3&th=1

 

much better options than amazon:

https://www.mcmaster.com/Heat-Shrink-Tubing/heat-shrink-tubing-type~end-caps/

 

unless some company out there would be able to make a perfect fit flat black silicone cap that can be installed over the handles and easily removed if you want to sell and the new buyer likes chrome.

Edited by kodiakdenali
1454 Enthusiast

1454

Posted
Posted
I was thinking of asking for tips since I haven't done this myself yet. did you take any of the pieces off or do the work with them installed? many of the chrome pieces are actually separable from what's around then. the ones around the LCD screen for example are attached with screws and some melted plastic tabs. you'd have to break the tabs, but they should be able to reinstall pretty easily. I'm wondering if all of that is worth the effort to be able to wrap the vinyl around behind the piece to prevent any chrome peeking through or if its possible to do just as good a job without taking things apart. any advice? could you post some pictures? I'd really like to see how it came out.

 

did you attempt the door handles by any chance? they will be tough due to the shape, I'm wondering if the chrome part of those can be removed somehow so the vinyl can be stretched and wrapped around the back.

 

No, I didn't attempt the door handles, because I didn't really intend on doing a full blackout job. I just couldn't deal with the glare. You have enough of an edge that as long as you use a sharp enough knife, you can cut around the edges. I used a mini squeegee to get it laid down tight to the edge and then cut the excess. I'm by no means a professional and there are small chome gaps. But it's far more tolerable than getting blinded by the sun. Just make sure you buy a minimum of 4in wide vinyl or you will have to do a ton of stretching like me. 226418daa3a1f4f17a54b1530f999474.jpg20149e1f5f4cefe4cca72c9c37910085.jpg 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined

  • Who's Online   2 Members, 0 Anonymous, 414 Guests (See full list)

  • Latest Articles

  • Posts

    • AlVeron
      Manufactuer's Defect - Paint Failure - Cherry Red High Country 2021 Suburban

      By AlVeron · Posted

      This is NOT impact damage nor neglect. There were previous class action lawsuits because of such paint preparation st GM manufacturing plant. Not just the Cherry Red Color. This paint is applied in three processes to obtain the desired color.  The manufacturer will cover for 36 months or 36k miles only. That rust is actually corrosion because of the paint process failure. Corrosion is covered for 100,100 miles or a certain months. However their corrosion doesn't include this type. Go figure. Clearly manufacturer knew from previous paint issues. This started 3 weeks ago out of the blue.  
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      Is it time to put a piece of tape over the CEL? 
    • davester
      2015 Silverado 3500 right rear turn indicator failure

      By davester · Posted

      consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...