Jump to content

Recommended Posts

Posted

Well, my last entry was Tuesday 12:47pm. Here it is Thursday night and I didn’t receive a call Wednesday or today. I’ll contact them again Friday morning and see what GM Customer Assistance has to say. My screen is doing the same things and I’ve disconnected the battery negative terminal twice. Just to see if that had an effect. So far, no improvement. There is a vertical dead zone 3/4 of the length left-to-right. Cannot adjust the fade control setting for front to back speakers. The bottom block (along that vertical 3/4 bar) for SiriusXM set channels doesn’t respond to touch. 

  • Like 1
Posted (edited)

Well, finally — it’s been 2+ months — and the dealer calls to say the part is in-house. So they scheduled for today to do the installation of the replacement touch-screen display. After a 3 hour installation, I am pleased to tell all that the display performs as expected. The “dead” right-hand side of the new display is functioning and I can once again use the settings to adjust the front/back speaker fade control up and down arrows. Thanks to the Chevrolet Customer Assistance Group in Center Line, Michigan at (800) 222-1020 or (586) 834-4780. My Senior Advisor, April, was never available to take my call. I called (865) 790-5600 Rishawnna (excuse the spelling) finally helped by contacting the dealership. I hope that I have better luck with this, my third, display. Bill H

Edited by Billhudson308
  • Like 1
Posted

Use your pinky more on the screen, less pressure. Jk

 

Dam, 3 hours installation? They should want to waste your time. It's a 10 min job at max. If you know what you're doing, it can be done in under 5 min.

  • 2 weeks later...
Posted

Same problem here - display jumps randomly. Dealer charged $260 "labor" just to download software updates yesterday! Replacement units are on "national back order" - unavailable. Updates were unhelpful, of course. Seems like a product defect.

  • Like 1
Posted
8 minutes ago, ALB3 said:

Same problem here - display jumps randomly. Dealer charged $260 "labor" just to download software updates yesterday! Replacement units are on "national back order" - unavailable. Updates were unhelpful, of course. Seems like a product defect.

What year & miles? 

Posted
1 hour ago, ALB3 said:

Same problem here - display jumps randomly. Dealer charged $260 "labor" just to download software updates yesterday! Replacement units are on "national back order" - unavailable. Updates were unhelpful, of course. Seems like a product defect.

you can get the Alpine upgrade, smallest one is 6" runs $900, the big 8" and larger screens are over $1200, then you need to buy the dash kit from alpine $500, and the GM CAN Bus adapter kit $??

Posted

Has anyone found a sure fire cause and solution to this problem? Bought a 2018 a month ago that seems to have this issue. Love everything else about the truck, but dealing with this issue nearly every time I drive it is infuriating...

Posted

Same thing happen to me starting a few weeks ago in my sierra (53000 miles). Dealer says it is caused by an update pushed out over the air by GM. They refuse to replace any parts or even look at it until they get more info from GM headquarters. There were 3 others in service this morning for same issue at the dealer. All GMC but not all trucks. I've been loyal to GMC for years but not anymore. I've had engine problems and now this. I'm tired of bad service and poor quality control.

  • 3 months later...
Posted

Yoo this happened to me as well mines at 27k, but took it to the dealership they changed the screen and hmi module supposedly a $1100 job (good thing i had warranty still). But tbh it started doing it again not as bad but still pretty annoying. Thing is they don’t even know what it is 🤦🏻‍♂️.

  • 2 months later...
Posted

Yep… bought my 2017 Silverado used with 58k miles on it… day after I bought it the screen started randomly swiping and map moving on its own… also if I’m using apple play it will randomly mute or put my phone call on hold… took it back to dealer and the tech was aware of the issue in this model truck and told me there is a back order on new screens to replace it… then told me that if the screen comes in after my warranty runs out then it’s not covered!!! What a bunch of BULLS*HIT!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...