Jump to content

295/65/20

CFRED70
 Share

Recommended Posts

CFRED70 Enthusiast

CFRED70

Posted
Posted (edited)

The dreaded "will they fit"?  I have a 2022 2500 everything stock.  I've heard guys running 35's so I'm assuming these fit, but is anyone running this size?  Next question is it worth going to this size over stock?  Only reason I'm debating is the deal I can get on this size over stock is better....just don't want to deal with rubbing issues.  Thanks

Edited by CFRED70
  • CFRED70 changed the title to 295/65/20
Dhamilton07 Enthusiast

Dhamilton07

Posted
Posted

I just picked up a set of new Toyo AT3s 295/65r20, $1300.  I did a lot of searching on the FB groups and saw a lot of members running this size with no rubbing issues.  I'm not worried seeing as the stock tires are already just over 34".  Haven't put them on yet, as I still have life in the current set, but that deal was too good to pass up.

  • Like 1
  • 1 month later...
Kevin B New Member

Kevin B

Posted
Posted

I just installed Toyo Open Country AT IIIs on my 2021 Denali 3500 with no suspension modifications except for Air-lift airbags in the rear. No rubbing driving on the road, but only about 1/2" between the inner fender and the tire at full lock in the front - any additional weight or bump in the road at full lock may cause a little rubbing....but who is hitting a bump with the wheel at full lock? 😄

  • 1 year later...
loinse bekean New Member

loinse bekean

Posted
Posted

One of the main concerns when upsizing tires is the potential for rubbing against the fenders or suspension components, especially during turns or over fnf game bumps. To avoid this, you may need to make modifications such as installing a leveling kit or lift kit to create more space for the larger tires. Keep in mind that these modifications can add to the overall cost.

  • 2 months later...
reb0957 Enthusiast

reb0957

Posted
Posted

I have been told over and over that the 295's will fit without a lift. We will find out next week!

295/65/20 Toyo RT trail

Random Enthusiast

Random

Posted
Posted
3 hours ago, reb0957 said:

I have been told over and over that the 295's will fit without a lift. We will find out next week!

295/65/20 Toyo RT trail

I installed 295/65 R20 BFG KO2's a couple of weeks ago and they fit without any issues with my stock configuration. I'm a big fan of how they turned out on the truck, so I imagine you'll be happy with your choice.

A Chap Enthusiast

A Chap

Posted
Posted

You know you can't brag about 295's fitting without posting a pic, right? 

  • 3 weeks later...
FreakBeast Enthusiast

FreakBeast

Posted
Posted

@Johnjr @CRApex @215robert have some savage looking rides with the new larger tires on them.

 

I just picked up my truck and intend to put BFG K02s on sometime next year depending on how the stock Goodyear Trailrunners hold up and perform this winter. I'll decide when I get there on 295/65/r20s or 35s. Seems they both fit fine based on what I could find looking around.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      If everything checks out at the MAF, then the MAF is BAD, new or not.   You don't need a signal generator to troubleshoot this. PCM needs ALL powers and ALL grounds able to light a halogen headlight bulb - if it can light the bulb bright, then the wiring is good enough to run the PCM.   Best thing you can do for yourself is spend some time here: scannerdanner.com - Check out all his YouTube videos on similar issues. If you decide to subscribe it's the best bang-for-buck ratio in the automotive world, hands-down. He's got TONS of free vids on YouTube, too.
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      You got that Hengst D110??
    • contrabombarde
      2010 Avalanche 5.3 not running correctly after engine swap.

      By contrabombarde · Posted

      Yes, I used my multimeter to probe all of the wires at the MAF, both with the sensor connected, sensor disconnected, key on engine off, key on engine running, etc etc etc. I probed all of the wires again at the PCM, at the connectors, etc. All voltages are what they should be according to the service manual/wiring diagrams. All grounds are good, less than 20 millivolts from the battery negative under load. Both at the connector of the MAF, at the PCM connector etc.      I know this throws a pretty big wrench into things, but this truck was acting up before the swap. I don't have very much information, if any on what was causing it, but if you cleared all of the dtcs it would do the same thing where it would crank, fire, then die. And it would do the same thing a dozen or so times, and eventually it would start and run, but the difference is that it would run and actually be drivable. Whereas now if you can drive it at all, it goes into reduced power mode almost immediately, and even then it's not running correctly. When you come to a stop at a light it stumbles down to for 500 RPM before catching itself and returning to the smooth idle. And if you go more than about 50% throttle then it immediately goes back to doing the misfire thing.    Like I said, I know that throws a wrench into things, and unfortunately I was not able to pull any data or anything like that before I did this work, so I don't have much to go on.    I'm trying to not fixate on one particular thing as the cause of the problem, but it seems like all avenues are pointing me towards the PCM. Like I said I have tested the wiring extensively (see above), and during cranking the sensor does produce seemingly legitimate values at least according to my multimeter, but as soon as the engine fires those values quickly descend into gibberish. I've tried it with multiple different known working sensors, I have done literally every test I can think of multiple times on the wiring (probing the signals, probing the pins with the sensors unplugged, probing the pins at the PCM, voltage drop, voltage drop under load, continuity, ohms, and double-checking everything against the wiring diagrams/ proper values in the service data.)    Another thing that pushes me towards a possible PCM failure is, I have noticed in troubleshooting a little bit taking a break and coming back, that when I leave the truck to sit for a while and cool off, it starts and runs smoothly when I first start it up. However once it warms up. It starts having problems. For example, when I went out to the truck this morning after it had been sitting overnight, I was actually able to drive it down the block. And then once I got on the throttle a Little bit after going about a thousand ft, it started misfiring again. I pulled it back into the driveway, shut it down, and started it back up. It idled smoothly. As soon as I touched the throttle it did the misfire thing again. From then on as soon as I started it it would misfire. I shut the truck off and went to go get a coffee and do a bit more research. When I came back out I started the truck up and it immediately went into the smooth idle. After a couple of minutes of playing around with it, it would not idle smoothly anymore. Let it sit a couple of hours, rinse and repeat. This makes me think with temperature change something is going wrong inside the PCM. I have the PCM out of the 2007 donor vehicle and I'm thinking of getting a one-day subscription to the ACDelco programming service to try and program that and see if it helps.   Like I said, I'm really trying to not fixate myself on one potential cause, but it seems everything is pointing me towards PCM failure. I would really like to try to confirm that, but unfortunately I don't have an oscilloscope or a signal generator to do the GM service procedure where you feed 5 khz into the signal pin. 
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      Ahh, sorry about that - I got some bad info. Newdude is correct. That's what I get for working 13 hours straight ... on my "vacation", lol.   Should've checked the files I had instead of the internet.   Anyway ... this is GREAT news, since this would've been an absolute friggin nightmare to get working.   I don't think the lack of VVT is causing this - you've got another issue. Wiring, I'm betting.   I'm telling you right now, your computer isn't bad. If it worked before the swap, it's working now. You need to do some more (better) diagnostics and figure out exactly what you're missing. Did you test every wire directly at the MAF? Have 5V reference? Ground? If you're reading ZERO g/s, your Hz isn't much use - it's going to be the wrong value anyway. The MAF is not working, and you need to find out WHY.   I got this off the net, so VERIFY first: Pin A: Black (BLK) wire, Circuit 552, serves as the Sensor Return (Ground).  Pin B: Tan (TAN) wire, Circuit 472, carries the Intake Air Temperature (IAT) signal.  Pin C: Yellow (YEL) wire, Circuit 492, is the primary MAF Sensor Signal output to the PCM. Pin D: Pink (PNK) wire, Circuit 339 or 539, provides Ignition 1 Voltage (Power).  Pin E: Tan/Black wire, Circuit 552 or similar, often associated with the Intake Air Temperature ground or signal return.  Global-A list: https://postimg.cc/KKJnQC85    
    • parthery
      GM Hard Folding Tonneau by REV review

      By parthery · Posted

      Correct....the end user can't reach to Realtruck directly like they can if they purchase a Bak, Undercover, etc...  It has to go through a dealer.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...