Jump to content

Is this a new 2013 Ford Truck, or a custom made truck?

flyboyron

By flyboyron
in The Off-Topic Bar

Recommended Posts

flyboyron Enthusiast

flyboyron

Posted
Posted

II am not sure if this is a custom truck or a stock truck, but I think it looks pretty nice.

 

 

header1.jpg

kstruckcountry Senior Enthusiast

kstruckcountry

Posted
Posted

Looks like a photoshop truck to me, as for the looks, to each his own I guess. Although I have to admit it's slightly less garish than the current SD. That's not saying much though.

 

EDIT: 6.0 grille and suicide doors, definitely photoshop.

SarahsGMC Senior Enthusiast

SarahsGMC

Posted
Posted

that is not the proper way to do a dually i do not like lol

 

just noticed bottom of doors are out of line and the white along the bottom is clearly brush stroke and poorly done at that

peteking Enthusiast

peteking

Posted
Posted

Toby Kieth used said truck in his "Who's your daddy?" music video a number of years back. I linked it on Youtube below

 

 

kstruckcountry Senior Enthusiast

kstruckcountry

Posted
Posted

Gotta say I love Toby's older stuff... his new stuff isn't as good though, and his concerts are like one big Ford ad sometimes.

KMGZ400 Senior Enthusiast

KMGZ400

Posted
Posted

Gotta say I love Toby's older stuff... his new stuff isn't as good though, and his concerts are like one big Ford ad sometimes.

 

 

i agree. beers ago is a good song though

Chris Senior Enthusiast

Chris

Posted
Posted

The truck was actually built. one was. it was built by doug deberti, he is a custom fabricator in bakersfield, ca. it was done for a sema show

flyboyron Enthusiast

flyboyron

Posted
  • Author
Posted

Well, seeing the video, I think the truck is pretty neat.

 

Probably couldn't afford it anyway. :nonod:

waumo1 Enthusiast

waumo1

Posted
Posted

That was a concept F350 Ford did in 2002 called the "Ford Tonka" (yes, that Tonka). Somebody photoshopped the sidepipe out (they are supposed to be where the white part of that picture is).

 

http://lmgtfy.com/?q=ford+tonka+images

 

That is funny because the first thing I thought when I saw the picture was Tonka Toy.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      It wouldn’t have happened if the government hadn’t mandated outrageous fuel mileage standards. It does very little for the consumer. It adds cost. Back during Covid there was a chip shortage. They gave a rebate for your truck if it didn’t have the chip to turn on cylinder deactivation. It was 50$ because at best you may see 1/2 a mile increase per gallon. Splitting hairs each fuel mileage trick wasn’t mandated. The government doesn’t do the engineering work and say use this until it’s already in use and they like it. The fuel mileage was mandated. And those add ons the results. There’s a mandate and they are the results.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...