What have you done to your K2 today?

[Crf450r420]

For my very first mods I ordered some weathertech liners, blendmount and a direct wire for my radar detector. Going next week to get my tint done.

I got the entire windshield done in Blue Air tint and it's great. Can't tell it's done other than it cuts down on the heat and UV.

[No Tyme]

how are they holding up?? I really like the look

I have only had them installed a couple of months and so far NO problems. They are powered coated so I am thinking I may take them off for the winter months when I put my winter shoes on... Still a few months off.

I was pondering having them painted a deep yellow so I have the Michigan State University's colors on my truck... LOL

Edited August 2, 2014 by No Tyme

[chuckl1218]

Installed Amp Bedxtender HD Max...

 

Edited August 2, 2014 by chuckl1218

[No Tyme]

I got the entire windshield done in Blue Air tint and it's great. Can't tell it's done other than it cuts down on the heat and UV.

I assume this gets applied to the inside? That's got to be a hard job to make it look good. Please give more info...

[Mike1220]

I got the entire windshield done in Blue Air tint and it's great. Can't tell it's done other than it cuts down on the heat and UV.

Do you mean the air blue 80% from Llumar? I was thinking if getting that on my windshield. It would bring it from 70% factory down to about 56%

 

Figured it would help a lot with heat and UV along with a fair amount if heat considering the windshield would be a weak point for heat entry if everything but it is tinted.

[Crf450r420]

Yes, the Lumar Air Blue. Can't even tell it's there before the dark strip at the top. My tint guy made me wait a month for the Air Blue to cure before he would add the dark top strips. Now there is no way you can tell just by looking through it. It will be adding it to every car I have have for now on. It's exactly like putting up a sun blocker when you park, but close enough and zero effort. You can't forget to put it up.

[No Tyme]

I assume this gets applied to the inside? That's got to be a hard job to make it look good. Please give more info...

I've research online and read poor reviews for this on windshields.

[Strykers_Inc]

Installed custom cnc billet pedal set.

[Crf450r420]

I've research online and read poor reviews for this on windshields.

It's great from my experience. Don't even have trouble with polarized glasses on. Not sure what else could go wrong.

[Crf450r420]

Installed custom cnc billet pedal set.

Looks good. Just aluminum with a wafer pattern and no rubber? I'd think that wouldn't be to great on traction if your shoes where wet.

[Crf450r420]

I replaced the bolt I dropped pulling my HMI for programming. I installed the AMP pass-thru harness, so now I can have my steps and my port. I started wrapping my trim pieces also. Got three of the doors done and just need to wrap the last one. I know how the center part around the LCD comes out, but I'm not sure how the center console pieces or the outer ones around the vents come off. I sure would like some help with those. I hate pulling on things not knowing for sure how they come apart. I didn't like how the black I did first had no contrast, so I switched it out. The stock silver was okay, but the doors and console were not plain. They had a pattern on it I couldn't stand.

[NitroDatsik]

I replaced the bolt I dropped pulling my HMI for programming. I installed the AMP pass-thru harness, so now I can have my steps and my port. I started wrapping my trim pieces also. Got three of the doors done and just need to wrap the last one. I know how the center part around the LCD comes out, but I'm not sure how the center console pieces or the outer ones around the vents come off. I sure would like some help with those. I hate pulling on things not knowing for sure how they come apart. I didn't like how the black I did first had no contrast, so I switched it out. The stock silver was okay, but the doors and console were not plain. They had a pattern on it I couldn't stand.

the trim around the ac vents just pulls off. Is only held by clips

 

Sent from my SM-N900T using Tapatalk

[Strykers_Inc]

Looks good. Just aluminum with a wafer pattern and no rubber? I'd think that wouldn't be to great on traction if your shoes where wet.

Actually the cnc grid is pretty sharp and has excellent grip...unless your wearing a shoe made of metal.

[Mike1220]

Yes, the Lumar Air Blue. Can't even tell it's there before the dark strip at the top. My tint guy made me wait a month for the Air Blue to cure before he would add the dark top strips. Now there is no way you can tell just by looking through it. It will be adding it to every car I have have for now on. It's exactly like putting up a sun blocker when you park, but close enough and zero effort. You can't forget to put it up.

And still easy at night to see out? I know the air blue would cut down the VLT a small amount. Not much, but still some.

 

I'm hoping to get my tint done in the next 2 weeks

[Texas Husker]

And still easy at night to see out? I know the air blue would cut down the VLT a small amount. Not much, but still some.

 

I'm hoping to get my tint done in the next 2 weeks

Your sorcery tint...? Still going that route? Edited August 4, 2014 by Texas Husker