Jump to content

rough country leveling issue

thewhitestallion
 Share

Recommended Posts

thewhitestallion Senior Enthusiast

thewhitestallion

Posted
  • Author
Posted

Mine is a Silverado LT Z71 CC with steel control arms. Bought last august, so assuming it was one of the early runs.

 

nope that didn't matter either. I ordered mine in sept of 2013 and picked it up at the end of nov 2013 with a build date of 11/13 and I have aluminum. there is a thread from a while back discussing this exact topic and it had hundreds of responses and there was no reason for why gm put what on the truck.

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

gmtech117
gmtech117

Why are you guys having such difficulty with this? Just install the bolts facing down so there is no clearance issues with the cv axle =the end . Every kit I've done I've had no issue installing the b

Posted Images

14SLTZ71 Enthusiast

14SLTZ71

Posted
Posted (edited)

i just installed my rough country 2" leveling kit on my 14 z71 4x4 and i saw somewhere another member saying that he had to cut a bolt because it was hitting his C.V. shaft but couldn't find the thread as im pretty sure it was in the middle of a picture thread or something. well when i installed mine today i had to do the same. you have to cut the rear most bolts that bolt the lower shock / strut assembly to the lower control arm other wise it will hit the C.V. shaft. i just emailed rough country about it and we'll see what they say. just an FYI for anyone who wants to put the RC kit on be aware that this is an issue. other than that issue it was fairly easy to put on.

anyone else put on a different kit that can chime in and say if they had this same issue?

here are some pics. gonna take some better pics tomorrow with a DSLR camera.

i measured before and after the install and it came out to just about 1/16" under an exact 2" lift.

I installed mine today and had the same issue, one of the bolts would hit the CV shaft if I installed it with the head of the bolt on the bottom per the instructions from Rough Country.

With the upper ball joint and steering linkage ball joint disconnected I was able to tilt the hub assembly enough to get the CV shaft out of the way and then put the bolts in with the head on the top side and nuts on the bottom. Here are some pics.

post-127588-0-20533300-1407710131_thumb.jpg

post-127588-0-56199500-1407716209_thumb.jpg

post-127588-0-11963400-1407716234_thumb.jpg

post-127588-0-20533300-1407710131_thumb.jpg

post-127588-0-56199500-1407716209_thumb.jpg

post-127588-0-11963400-1407716234_thumb.jpg

post-127588-0-20533300-1407710131_thumb.jpg

post-127588-0-56199500-1407716209_thumb.jpg

post-127588-0-11963400-1407716234_thumb.jpg

post-127588-0-20533300-1407710131_thumb.jpg

post-127588-0-56199500-1407716209_thumb.jpg

post-127588-0-11963400-1407716234_thumb.jpg

Edited by 14LTZZ71
Daryl LBZ Senior Enthusiast

Daryl LBZ

Posted
Posted

The Zone Offroad leveling kit I installed on my 2011 was the same way as far as the bolt hitting the CV shaft. I had to unbolt a few extra pieces and put the bolt in with the head up. Worked out fine after that just like posted above.

  • 4 weeks later...
Trueman09 New Member

Trueman09

Posted
Posted

I just installed my rough country kit and noticed the same thing, but in my box I had 2 sets of bolts, the shorter and longer. I used the longer installed as the said and it was close to the cv, so I installed the bolts going down without cutting them, I didn't have to remove anything extra from the directions it just went straight and it worked a lot better that way then going up.

  • 6 months later...
chevydeth Enthusiast

chevydeth

Posted
Posted (edited)

I'm looking to buy this kit soon, 2015 double cab z71 4x4, appears they are steel (painted black). Is it okay to put the bold facing down with the nut closest to the ground to avoid the bolt sticking up hitting the cv?

Edited by chevydeth
  • 1 month later...
tyrich88 Enthusiast

tyrich88

Posted
Posted (edited)

From what I have gathered here, it's fairly easy to tell if the arms are aluminum or steel, but a Silverado LT Crew Cab 4x4 (non Z71) should have steel arms... correct?

Edited by tyrich88
  • 2 months later...
Iflyforfood Enthusiast

Iflyforfood

Posted
Posted

glad to find this thread & find out I'm not the only one... Just picked up my 2015 crew AT yesterday & immediately put the RC 2.5" kit on. Well, tried to.... Bought the aluminum kit as RC told me that even if I had steel arms, I could "flop the bolts over" and it would work. Turns out I have steel arms. Tried to install with the stock nut clips & really didn't like the lack of CV clearance. RC said to just cut the bolts... Decided to find some shorter bolts and try the supplied locknuts on top as the locknut is a little shorter than the stock clip. Went and found some 75mm bolts locally (nobody had any 80mm) which BARELY engage the nylon part of the locknut. Still didn't like the clearance. By now is was 1am with a 10am appointment for 33" tires so I threw in the towel, reverted to stock, canceled the tire installation and went looking for info like this. The not-so-smooth front install got me thinking if I really wanted to mess with a perfect brand new truck..... love the leveled look but I do need to rely on this vehicle! I guess I'll try the heads-up approach after I convince myself that modifying the suspension is a good idea in the first place.

El_Diablo_John Enthusiast

El_Diablo_John

Posted
Posted

I have steel arms on a 2015 4x4 LT. The instructions provided said to install the bolts up and I had to cut mine. This was with the RC 2.5" kit for steel arms.

Iflyforfood Enthusiast

Iflyforfood

Posted
Posted

I bought my kit a few weeks ago & the instructions said heads up! strange. El_Diablo, did you use the stock nut clips or the locknuts that came with the kit? any signs of rubbing on the driveshaft with your installation?

gmtech117 Enthusiast

gmtech117

Posted
Posted

Why are you guys having such difficulty with this? Just install the bolts facing down so there is no clearance issues with the cv axle =the end . Every kit I've done I've had no issue installing the bolts down, and all the kits I've seen the instructions say put the bolts down.

  • Like 2
El_Diablo_John Enthusiast

El_Diablo_John

Posted
Posted

I bought my kit a few weeks ago & the instructions said heads up! strange. El_Diablo, did you use the stock nut clips or the locknuts that came with the kit? any signs of rubbing on the driveshaft with your installation?

You must use the new nuts provided with the new bolts. No signs of rubbing on the axles so far. I do plan on replacing the hardware with shorter grade 8 hardware eventually though.

 

I didnt want to risk having the hardware hanging down and when I tried the bolts provided would even clear the axles. Simple as that.

iCryWheniGoPoop Enthusiast

iCryWheniGoPoop

Posted
Posted

I added a couple extra washers to the CV side

robvas Enthusiast

robvas

Posted
Posted

Same thing happened on mine. Had the same guy install my Skyjacker blocks and he didn't have the problem, not sure if the bolts were different or what.

 

29SIzPa.jpg

iCryWheniGoPoop Enthusiast

iCryWheniGoPoop

Posted
Posted (edited)

Same thing happened on mine. Had the same guy install my Skyjacker blocks and he didn't have the problem, not sure if the bolts were different or what.

 

29SIzPa.jpg

Those bolts are to short... You are not utilizing the lock not and will more than likely experience issue with a nut coming loose. At minimum I would put red loctite on them to avoid issue. A good rule of thumb is no less than 3 bolt threads showing past nut. Edited by TDT
iCryWheniGoPoop Enthusiast

iCryWheniGoPoop

Posted
Posted (edited)

double posted

Edited by TDT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      https://www.msn.com/en-us/autos/general/what-makes-this-1963-ford-falcon-red-rocket-special/vi-AA2asoRz?ocid=winp2fptaskbarhover&cvid=be9c1b4f79ff4211c526abd60f6da012&ei=16
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      True. My statement needs qualification. "For a shade tree mechanic, re-assembling the front engine to achieve a rough baseline timing of 0 degrees, as is approximated and indicated by common visual indicator mark alignment, measured with a human eye capable of 20/20 vision *with correction, I am reasonably confident that I have followed the outlined procedures/ prescribed methods for verifying baseline timing."   😉   In the end, the computer sets the timing, it's continuously variable based on sensor input, and the distributor only has a degree or two of physical adjustability intended for dialing in the final setting for cam ****** once everything is back together. But even that final value is acceptable within, I believe, +/- 3 degrees.   I thought my exhaust project was going to be a bear. To my surprise, the old clamps came right off last night, and I was able to unbolt all the hangers instead of having to muscle the rubber mounts. The old cat is ready to slip off the factory y-pipe. The rest is ready to come out with one or two cuts, and I've got a fresh blade waiting. I love living where rust isn't a thing.    
    • Bloody Marty
      PF63 Oil Filters Going Away?

      By Bloody Marty · Posted

      I work at a Chevrolet dealership & hear it all believe me.  Just reads like there's going to be a fist fight over filters.  Can't get enough, continue!!
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I just can't think of the exact term GM uses for that higher gvw package without looking at the website but basically sort of a trailering package and I imagine it may also have been created to skirt around the licensing fee differences between a3/4 and 1 ton that apply in some states although ironically I believe in some states its the reverse that a 1 ton is the cheaper truck to license over a 3/4 ton. It makes no difference here in Alberta but oddly enough a 1 ton through my insurance company is a bit cheaper to insure over a 3/4 ton as its based on the insurance statistics they generate.    For sure when ever you do have the chance to weigh your truck and to be fair, try to have the fuel tank full or nearly so rather than give yourself a false sense of the truck being lighter by having an almost empty tank.    In my other comment I was mentioning stock sized tires and partly in case someone was reading this and thinking they could lower their pressure down to what your aftermarket tires are able to do with your empty truck as that is a vastly different picture in the leeway you have to play with for running minimum pressures while remaining safe. I will say also that its easy to see from reactions of truck owners that may have been more used to owning a half ton in the past or a car and be it on a forum like this or in person etc that they get so wrapped up in that placard pressure sticker that they can't get their head wrapped around the fact that an HD truck due to how much it can carry can also vary the tire pressures drastically lower than those pressures ( typically more so for the rear axle on stock sized tires ) when empty vs some car that isn't made to carry much so the tire pressures can't be lowered since it needs almost that much pressure just to carry the empty car.    If I ever do find myself in the states with this truck, I will only be too happy to switch it over to the US measuring system as then I will understand all the dash readings. The only thing that is off for me slightly with US measurements is US miles per gallon as I grew up with the Imperial gallon and to this day up here anyway speak in Imperial miles per gallon ( I don't do that on this forum though as that would confuse everyone for no good reason ). 
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Yes that's right, it's the upgrade that includes the overload spring and all that stuff.   Someday when I'm empty and going by a scale I'm going to stop in and get some weight readings.   Exactly  you should have the ability to change individual settings, in in Canada so I'm driving with kph but then I'm stuck with kpa when I want psi lol    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...