Jump to content

Recommended Posts

Posted

Is getting the rear cover gasket from the dealer the best option?

 

To clean the G80, brake cleaner?

 

No silicone, right?

Posted

The gasket is reusable if you carefully remove the cover. Brake cleaner works well along with a lint free cloth. Refill with Amsoil Severe Gear oil.

Posted (edited)

Thank you. So spray the inside of the diff, wipe inside and good to go?

 

Chlorinated or non? Does it matter?

 

 

Swapping out front to Amsoil too.

Thanks again.

Edited by WilliamBos
Posted

Thanks again. Woukd you happen to know the service intervals for the rear diff?

 

 

Sent from my Z30 using Tapatalk

Posted

I bought a gasket from Amazon. I have the 14 bolt rear end

 

 

Ryan

Posted

I did my rear end, no G80 though. I bought a new gasket from group1autoparts.com However, as mentioned earlier, I realized I could have reused the casket. It's not the paper/cork jobs of previous years, its a reinforced rubber unit. Pretty beefy if you're careful. Careful reading of the service instructions indicate that the unit can be refilled to the bottom of the fill hole. As always, be sure to remove the fill plug before taking the cover off so you ensure the ability to refill the unit after draining it out.

Posted

 

 

Thanks again. Woukd you happen to know the service intervals for the rear diff?

 

 

Sent from my Z30 using Tapatalk

Depends on the usage, but 50k miles if used hard, or if no towing 100k.

Posted

Thanks. I only tow twice a yeae., 60 km round trip. Will do.it at 75,000 miles.

 

 

Sent from my Z30 using Tapatalk

Posted

 

 

Depends on the usage, but 50k miles if used hard, or if no towing 100k.

Planned to change mine @ 70K mi.s since last done. Bought synthetic, gasket.

Checked oil. Pristine...could have put it back into bottles & sold as new.

I'll wait a while.

Posted (edited)

Skip the cleaner. Just drain and refill. This isn't a major contaminated area. All will be fine. You risk more by trying to clean it out and having a dry spot on the bearings and gear set when you go to move the vehicle. Best to leave it alone and have a fluid film on everything until the fresh gear oil can lubricate everything.

Edited by Black02Silverado
  • Like 1
Posted

Yep I agree with Black02Silverado. Back in the day (and even today) some guys liked to run kerosene or diesel through the crankcase to "clean it out". No thanks! I've never done this to an engine, trans, or diff.

So, is that gasket reusable on the '07 new body G80?

 

I changed the oil at 40k by vacuuming it out of the fill hole 5 years ago. I didn't have a gasket on hand and didn't feel like running around trying to find one at the time. If I can reuse it, I'll be more inclined to change the oil when it's needed. :lol: I like pushing Amsoil to it's limits ...

Posted (edited)

The gasket is a metal lined rubber gasket that is reuseable. I am gonna pick one up though, it my only vehicle. Better safe than sorry.

Edited by WilliamBos
  • 6 years later...
Posted

I replaced fluid on my 2011 sierra 1500 wt 2 wheel drive at 120k mi for the first time.  I bought a new gasket and 3 bottles of AC-DELCO fluid from a dealership because I didn't know if after-market fluid works ok for my truck.  old fluid was totally black and burnt.  a shot glass full of metal powder was inside.  Gear surfaces looked all in good condition.  the truck has been a commuter vehicle with no towing or heavy load.  After the fluid change, I did a 500 mi long trip in one day with no issue.   I plan to do another fluid change at 180k mi or so.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined
  • Who's Online   5 Members, 0 Anonymous, 610 Guests (See full list)

  • Latest Articles

  • Posts

    • Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 
    • This landing is worse than most. Patchy blacktop with washouts, soft gravel/sand at bottom that washes out with every heavy rain. I tell everyone to put it in 4WD. A lot of them think they can pull out their trailer in 2WD. They end up digging a hole and then putting it in 4WD.  The lake is a pristine lake and has a lot of money on it. There are several wake boats and lot of large tritoons. The people with the money don't want it improved because they don't want more traffic.    Boat Landing 1.jfif Boat Landing 2.jfif Boat Landing 3.jfif
    • How wide are your rims?   Toyo specs 8.5-10.0-11.0 inches. My thought would be rim might be pulling the tire inwards creating a center that is more pronounced.    I also noticed that the spec sheet says max 65psi. So you could be right lowering the pressure to ~40 psi. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...