Jump to content

2017 Silverado WT Key fob installation

crabbcat

By crabbcat
in Modifications & Accessories

 Share

Recommended Posts

crabbcat Enthusiast

crabbcat

Posted
Posted (edited)

Ok, need some help.  looked around here and there is no good information on installing key fobs on a 2017 Silverado WT.  It did not come from the factory with them.  I have the Au3 code in the glove box. The dealer thinks it needs a very expensive kit. I have onstar, power door locks but no gosh darn key fobs. I do not need remote start. Just need to install key fobs  Also very little information on the internet. Local stereo guy says he can't do it. 

Edited by crabbcat
Enough Enthusiast

Enough

Posted
Posted

crabbcat, I'm confused too !  My 2016 Silverado WT with the AU3 code for power locks came with two factory remote key fobs when I bought it new. I also have the A91 code for power tailgate lock and A31 for power windows so maybe that is the difference.

 

Why in the world would the truck have power locks installed from the factory with no way to activate them from outside of the truck ???

 

If you have Onstar and the MY Chevy app on your smartphone you could use it to lock and unlock the truck but that's kind of a pain.

newdude Senior Enthusiast

newdude

Posted
Posted

Have the dealer program a key fob and see if it works.  You have tire pressure sensors which use the same exact module that the key fob uses, the RCDLR (remote control door lock receiver).  I have done this twice in the past with success. 

crabbcat Enthusiast

crabbcat

Posted
  • Author
Posted

I'm going to try it Monday. My dealer said i need to go to a radio guy...lol  I have found in the past they are completely useless when they worked for two days installing the wire/programming on my aftermarket oem 16 colorado fogs.   They had the wire in the wrong hole in the fuse box so i fixed it myself...lol I talked to another parts department in a town close by and he sounded amenable so i will try him. Thanks. I'm also going to ask about a backup camera. 

redwngr Senior Enthusiast

redwngr

Posted
Posted (edited)

Remote start kit from GM accessories is listed at $275 for 2017 1500 silverado

 

https://accessories.chevrolet.com/product/2017/Chevrolet/Silverado 1500/remote-start-kit-22997089?categoryId=12013

 

 

I agree with the others that you maybe just need to talk to someone else at the dealer, or perhaps at another dealer.

Edited by redwngr
passat774 Enthusiast

passat774

Posted
Posted
1 hour ago, newdude said:

Have the dealer program a key fob and see if it works.  You have tire pressure sensors which use the same exact module that the key fob uses, the RCDLR (remote control door lock receiver).  I have done this twice in the past with success. 

 

 

My 14 WT, I took the same steps. My dealer took a remote programmed it in less than 10 minutes!

Paintor Enthusiast

Paintor

Posted
Posted (edited)

 

Think so. Also an interesting note....GM changed the frequency from 315mhz to 433mhz in 2017....for your FOB and TPMS sensors. Cant use 2016....who knew? 

 

 

 

Edited by Paintor
crabbcat Enthusiast

crabbcat

Posted
  • Author
Posted

Called a local dealer today. The only way i could get key fobs was to get the whole remote start/ hood kit.  275.00 + 1-1/2  hrs labor 180.00.    So about 485.00  but i get the remote start, hood latch and itshould be covered under GM warranty and my extended warranty.  The stereo guy wanted 300 for non oem keyless entry. A no-brainier to go with the dealer this time because with luck i get the alarm too. Get it installed tomorrow at 2.00. I'll update with exactly what i get.  I really didn't want to spend this much but ill see what happens.  He's looking into the rear view camera so maybe i can get a deal on it. Otherwise i can get one myself. After the camera the level kit and gatorback bed cover Thanks!

crabbcat Enthusiast

crabbcat

Posted
  • Author
Posted

Did the remote start kit today from the dealer,  461.00 installed and everything works, even the alarm. Well worth it as it was going to be almost 300 for the stereo guy just for non oem fobs. They had a fit with updating the bcm but finally gotit done. The parts guy was a huge help in all this. Next up level it, then rear camera...lol  Thanks for your help. 

Nhcampbells Enthusiast

Nhcampbells

Posted
Posted

So I have a 17 2500hd WT. I been reading all about the rpo codes needed. I do not have some of the codes that some say you need, but my truck has remote entry, and onstar and 20” wheel package. So I’m not sure what’s going on. After a go around with the dealer and having to call Chevy they say I can put the remote start in for 413 dollars. Another dealer wanted $605. Waiting for the new fobs to come in so most likely next week. Hopefully this goes well. 

I have a post going also and had some good feedback on aftermarket ones also 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • AidenVorpagel
      cam upgrade in CA

      By AidenVorpagel · Posted

      hello I recently bought a 2012 gmc 1500 with a 5.3 and have a AFM disabler on it I'm interested in doing a cam but I'm worried if I remove the AFM system I will fail smog does anyone have info if they are able to detect that or a work around to it (not talking about hot smogging) please let me know thank you  
    • B14Sierra
      Noise after AFM delete

      By B14Sierra · Posted

      Did you figure it out?
    • B14Sierra
      Possible lifter tick after DOD delete

      By B14Sierra · Posted

      Update. I started chasing down my symptoms. Started first with pulling valve covers and looked at everything. Everything looked good and couldn't hear or feel anything different. Then a compression test. 240 psi or really close on each cylinder. I was worried I was a tooth off of timing. Not bad for an engine with 173,000. Granted I did put new heads on. I sprayed water around the injector area to see if I could hear a change. Nothing. I hooked up my new hp tuner which I should have done in the first place but I don't really know what I'm looking at just yet but am learning. I noticed the fuel trims were way off so that told me I have to have either a bad injector or exhaust leak. New injectors, so I did the shop vac on blower and in the tail pipe. Sprayed soapy water and found the exhaust flange on the drivers side was leaking. I didn't think it would be that considereding I pulled the heads and left the manifolds attached. I did have the transmission replaced not long ago. They must have not seated them properly but I guess I didn't notice. I put in new gaskets on both sides. Which by the way isn't a bad job but I had a hard time getting them to seal right. Took two attempts. Reset the fuel trims and the ticking is gone, engine runs smooth and acceleration has improved. Got to feel the real difference with that stage 1 cam. It's not that big of a difference but it does add a little more. It feels like how the truck should have been from the factory.
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled I?    Stribeck says that we need a certain amount of viscosity under conditions of load and velocity to prevent two surfaces of a know roughness from tearing each other asunder. And we have marketing trying to tell the masses that those two surfaced require less of that commodity due to more exact limits being placed on the same old clearances. We also know that there are limits to how hard something can before it becomes to brittle to be viable and to smooth to 'wet' the surface and that both of those conditions have been known and met since about the Second World War.    That viscosity value shook out at 10 centistokes at 212 F just under a hundred years ago.  Give this a look: [Anton Parr]     What is advertised is the Kinematic viscosity (mm2/s) or that which has been density adjusted but the value we are after is the dynamic viscosity (mPa.s) or true viscosity. You can see that this number is dependent on density thus base stock and temperature. You can also see that an SAE 30 doesn't reach that value in this example. However an SAE 30 that is at the upper end of the SAE 30 range; 12.5 cSt (mm2/s), might. 12.5 * .83 = 10.375 (mm2/s). If you could find an SAE 30 at the upper end these days.   Then there is the complication of viscosity modifiers or VII or VM, whatever you wish to call them. Polymers added to very thin base oils, perhaps 3 to 6 cP oils, that will meet the SAE *W30 spec at 'tested' shear rates and 100 C/212F  target temperature. So a polymer fortified base that is a fraction of the 10 cP requirement Stribeck insist upon.   This could be all well and good if those polymers didn't have two very problematic 'features'. They shear or loose viscosity both 1.) permanently and 2.) temporality. And they do both omitted in the advertised data with the distinct  purpose of deceiving the consumer of the actual operating state of the fluid. I've shown the example of Warren Oils COSTCO 10.91 cSt 5W30 formuation several times where the 100 C HTHS value is 6.9 cP!! That's the temporary shear down and with and SSI or shear stability index of 9.4 cSt. Note the intentional deception in using mixed units?    After a short while that 9.4 cSt oil has a viscosity corrected dynamic value of 7.8 cP. But as the SSI is still within the range of an SAE *W30 whose lower value is 9.3 cSt.    This allows them to continue to call this SAE 16 weight oil a 30 weight, the cake, and still meet the API requirements for fuel efficiency IMPROVEMENT mandated by the EPA. The eating of the cake. By the time you've worn out your motor doing the responsible thing by adhering to the warranty requirements, (the stick), you get deprived of the carrot, wear control. So sad, to bad.   So what can be done? Do I need actually say? [Anton Parr]       Even this must be monitored if the oil is on the low side and the VII an organic or you opt for a 0W40 with an even lighter base oil and more / higher MW VII. (Note the lower density of the 40 weight versus the SAE 30 mono-weight?)    There is another workaround. Temperature. An SAE *W30 run at a bulk temperature of between 180 and 195 F.    Being the belt and suspenders sort I am I do both. Run it cook and run it heavy.    In Part II I'll work the AW package. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...