Jump to content

Any new news on GM retiring the 6.Dinosaur ?

f8l vnm

Recommended Posts

K2xxSteve Enthusiast

K2xxSteve

Posted
Posted
6 hours ago, avalonandl said:

AFM makes no sense since the 2500 series is exempt from CAFE...

 

In regards to the 3800 V6, it was a great engine. The LS cylinder head is better with its cathedral  shape and revs better. The 3800 was EFFICIENT, but at low rpms. 

Yes, but imagine a 3800 "Series IV" with some LS head treatment love. Woulda loved to see it but they just moved to the 60* DOHC platform for the V6's.

  • Replies 79
  • Created
  • Last Reply
Mdmartin3z Enthusiast

Mdmartin3z

Posted
Posted

it may be wishful thinking, but I’d like to swap this new 6.6L gas in for my 6.0 after it dies at 900,000 miles ?

Princess_jamie Enthusiast

Princess_jamie

Posted
Posted

The 6.0 may be a dinosaur and a dinosaur is in the reptile family.  Some reptile species are known to outlive humans therefore making the title of the thread highly accurate when referencing the 6.0 to a dinosaur.  I do believe someone on this forum has their 6.0l, 6l90 combo up to 500,000 miles without major repairs.  

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Charly
      Frame rusted out

      By Charly · Posted

      I am new to this… but I saw some of your replies to another person doing the same as me… trying to replace the temp control actuator in my 05 GMC SIERRA, And can NOT get to it… how do I get the center console panels off, do I have to take ALL of them off to get to it? 80481681120__F97CE005-C5E5-4FBF-9589-1388214E3586.MOV
    • Jus Cruisin
      2027 GMC Sierra: Official Discussion

      By Jus Cruisin · Posted

      I will be one of those "blinded". One, I like new shiny things. Two, I've never kept any of them beyond the 3/36. Three, I don't finance anything. Four, yep, it's a waste of money....so,what? I'm doing my part of keeping automotive industry going and keeping my neighbors, most of whom are in it, employed. 😉      By the way this is the "signature... ¬  
    • marpel
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By marpel · Posted

      Although there is a "recommended" weight by those who sell trailers, my experience has been that they are way too aggressive in their information, for me at least. My '22 with 6.6 Gas, has a payload of about 3400 lbs and depending on your specs (I don't have 4WD so it has a bit higher Payload than others) yours will likely be different. Payload is one of the most important numbers for towing. Although you "could" tow the max trailer weight for your truck, I, personally, would not go close to that number. Having said that, a lot depends on how/where you will be towing. I live in the LMD of BC and often tow to Denver, Co, along interstates (flat and mountains) and I find I need to keep it in 5th (6spd) for the trip and travel at around 65mph. This is for a trailer dry weight of just under 3500lbs. If you are only doing local, short trips, it would not be that big an issue if you had a heavier unit. You will be surprised how much stuff you load the trailer with, so I would only recognize the trailers "full" GVWR weight rating, then decide on the appropriate trailer from that number. If you are worrying about how much stuff you should be putting in a trailer, you might have too large a rig from the get-go. Once again, depending on what terrain/distance in which you will be pulling. Marv
    • marpel
      Disconnecting Battery

      By marpel · Posted

      davester, Thanks for the response, how ever, I think I am now a bit more confused than I was before I posted - - After I posted, I actually found a YT video of a guy who replaced his Module (above tire) and he only disconnected the ground cable of the battery, but you describe rubbing the two cables together after disconnecting. I presume that is to do as you describe and eliminate any residual energy? - When I picked up the Module (between my posting and reading your response) from the dealer, I specifically asked about any re-programming and he stated it was not necessary as it was simply plug and play. Don't know how knowledgeable he is, though. - The video I watched also showed the Module plug to be difficult to "unlock" and remove, but there was no mention of silicone, although the video did show a bunch of dust/dirt in and around the plug (old truck) during removal. Are you talking about silicone that was applied by the factory, or silicone that you applied prior to plugging in? Thanks again, Marv
    • mandrautomotive
      2022+ GMC Hummer EV 40" Bumper Light Bar PRO: Factory Fit, Maximum Output

      By mandrautomotive · Posted

      Looking for a clean, factory-style lighting upgrade for your 2022+ GMC Hummer EV? M&R Automotive's 40" Bumper Light Bar PRO features a vehicle-specific, bolt-on design with no drilling or cutting required. Choose a bright white or yellow main beam, both paired with an amber DRL backlight for a sleek OEM-inspired look. The kit includes a curved LED light bar, powder-coated brackets, and all necessary mounting hardware.    Learn more or order yours See how it installs and looks on the vehicle:    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...