Jump to content

AVS Aeroskin Lightshield

ShamrockShooter
 Share

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Suprmario
Suprmario

Went for it myself....might not be for everyone, but I like it..  

Suprmario
Suprmario

Wiring pics  

ShamrockShooter
ShamrockShooter

Anyone install one of these yet with the lights?   https://www.autoventshade.com/avs-753168-aeroskin-lightshieldhood-protector   Sent from my Pixel 2 using Tapatalk    

Posted Images

  • 1 month later...
Kchampagne Enthusiast

Kchampagne

Posted
Posted
On 2/16/2020 at 8:37 PM, jflan23 said:

 


I looked at their website earlier they do have one for the new Sierra’s

 

Has anyone installed one of these on a Sierra?  Pics? I bought an "open box" one on Amazon for $48, but haven't installed it yet.

ETMC Enthusiast

ETMC

Posted
Posted

One of the reviews I read was a complaint about wind noise. Anyone on here with that problem? 

  • 4 months later...
Craig N. Enthusiast

Craig N.

Posted
Posted

Can’t thank you enough on the wiring pics! Looks sharp and has minimal noise on my 2020 Trail Boss. 

9750673D-0E42-4DA4-AF03-C078F7767C24.jpeg

Kchampagne Enthusiast

Kchampagne

Posted
Posted
On 8/31/2020 at 3:07 PM, Craig N. said:

Can’t thank you enough on the wiring pics! Looks sharp and has minimal noise on my 2020 Trail Boss. 

9750673D-0E42-4DA4-AF03-C078F7767C24.jpeg

Craig N. your truck looks awesome!  Where did you get your tow hook shackle conversion kit? I like it!

  • Like 1
Craig N. Enthusiast

Craig N.

Posted
Posted
1 hour ago, Kchampagne said:

Craig N. your truck looks awesome!  Where did you get your tow hook shackle conversion kit? I like it!

Thank you! I needed to make it different than the others out on the road. Rough country makes both the brackets and the recovery shackles. Let me know if you have any problems tracking them down. I had to do some digging for the shackles. 

Kchampagne Enthusiast

Kchampagne

Posted
Posted
1 hour ago, Craig N. said:

Thank you! I needed to make it different than the others out on the road. Rough country makes both the brackets and the recovery shackles. Let me know if you have any problems tracking them down. I had to do some digging for the shackles. 

Thanks!

Solarplex Enthusiast

Solarplex

Posted
Posted
Looks like the textered matte black finish on the one above. Do they offer the smoke clear/gloss black in one of these?

Yah i would like one in gloss as well to match the grill and bumper. Looks like they make colour match so yes, gloss black.


Sent from my iPhone using Tapatalk
  • 3 months later...
sully12 New Member

sully12

Posted
Posted

Hey everyone, was hoping someone could help me with this install. First, I can't pull out the wiring harness behind the driver side headlight. I got the red pull tab to come out, but can't pull the harness out. Any tips to get it off or is my only option to remove the grill to better access the headlight? My second thought was to use a piggyback connector on the fog lamp fuse, #49. Im clueless when it comes to electrical, so I'm not sure if that would even work? Are there any other ideas to wire it more simply? Thanks

Shoup1cobra Enthusiast

Shoup1cobra

Posted
Posted
39 minutes ago, sully12 said:

Hey everyone, was hoping someone could help me with this install. First, I can't pull out the wiring harness behind the driver side headlight. I got the red pull tab to come out, but can't pull the harness out. Any tips to get it off or is my only option to remove the grill to better access the headlight? My second thought was to use a piggyback connector on the fog lamp fuse, #49. Im clueless when it comes to electrical, so I'm not sure if that would even work? Are there any other ideas to wire it more simply? Thanks

I removed the headlight bulb and tapped into that harness. It was much easier than trying to reach the entire harness at the bottom of the headlight. The posi lock connectors and exisiting wiring can tuck in behind the bulb and then everything gets covered by the large rubber flapper. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Sdid
      2020 Silverado 1500 8speed gm needs to recall transmission

      By Sdid · Posted

      I have A 2020 1500 5.3 8 speed. LTZ. Transmission problems since 60,000 miles. Started when I go to store in morning to get my morning coffee before work leave truck running get back in put it in drive/ rev no movement step on gas a little slams into gear. Put in neutral step on gas little shake then put in gear and gose.  Shut truck off start .. ok now at stop light stop truck after a few seconds feel a little kick if that doesn’t happen stuck in 3/4 gear shut truck off wait few seconds and start usually ok again. If you down shift manually ok as long as you get into 1st before stop. If not it kicks . I WANT A NEW TRANSMISSION. Now I want a new truck it just hit 80,000 IDK IF ILL BUY CHEVY CAUSE THEY STILL HAVE THE PROBLEM AND REFUSE TO RECALL . Oh I’ve changed the fluid and filter 3 times now. And yes used mobile 1 not ac/delco cause it’s not meeting the requirements that mobile is did use ac/delco filter 
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Of course refrain from political debate but I myself have very dismal hope for what is all going on up here every where we turn so I nodded my head when I saw this joke.     
    • diyer2
      Navigating senior years.

      By diyer2 · Posted

      I'm looking at carpal tunnel surgery on my left hand and lumbar fusion. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      While waiting for parts I have been working on installing the AC compressor, new accumulator, and orifice tube. Also changed out the high side ball valve (original). The orifice tube that was in there wasn't too bad. Slightly dirty, a little bit of junk, but not blocked. Glad I changed it out.   The accumulator, which should have been a 5 minute job, may have just burned $50. Put some PAG in it, wrote the date and mileage on the side, fresh o-rings and gooey'd up the threads and rings with Nylog. Got everything connected and snugged and was going to vacuum down the system, and....   My manifold gauge won't fit on the port. It's not an R12 service port. It LOOKS like an R134 service port but the diameter is a hair too large. There's a sticker on the accumulator that says it's designed to be used with R12 and R134a systems only. So it's not R1234yf. Even if I reduced the diameter slightly with a file, the shoulder on the port is too large so the quick-connect valve won't lock on. I'm stumped. It's going back, and 50/50 on if they'll give me a refund.   Also, I did a fuel pressure test.... Key on, the gauge spikes to about 60psi and quickly bleeds off, like 2psi per second. The fuel isn't going into the plenum, no smell, starts fine, so I'm guessing there's a bad check valve in the pump and the fuel is just draining back into the tank. oh, hell. But, it shouldn't be a problem, pump primes just fine and the truck starts right up. It just means I can't really ever use fuel pressure to verify a leak at the injector or intake.
    • No F-bdy Bs
      SERCICE ESC message?

      By No F-bdy Bs · Posted

      Got this yesterday out of nowhere. Truck is a 25',6.6 gasser with 8k miles.  Only semi anomaly is that the truck had been sitting, uncranked for 6 days. Elec Stability Control showed immediately upon cranking, not while driving. No drivability issues, just the message. Battery didn't seem to be weak when cranking over.  I drove it, killed it, let it sit a few hrs with no avail.  Truck is 100% stock. No damage. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...