Jump to content

Recommended Posts

Posted

A tale of two TRXs.

 

Mine on mile 40 of a highway run in 90 deg heat. IMG_3931.thumb.jpeg.18a285ae2cd4d3ef67f266ee6e2f34d6.jpeg

Oil: 199 (Red Line 5w50 just installed)

Coolant: 185

ATF: 165

 

Meanwhile this is what most people think is OK:IMG_3933.thumb.jpeg.c2f7da326ce96472b7f502a41510fbf4.jpeg

ATF: 214

Coolant: 234

Oil: 286! (Factory approved 0w40, gotta save that warranty).

 

The fluid temps were well within allowed range. 286 may seem high but it was for a short period and is OK with fully synthetics. TRX has safety limits, which were beyond these temps.” 
 

What’s the safety limit? Punching a rod through the oil pan to add extra ventilation? 😂

 

We’re getting beyond blind faith in the OEs and into pure ignorance at this point.


I heard an analogy somewhere that I liked. Imagine your body had a full warranty for 40 years. Would you smoke 3 packs a day and eat only McDonalds because all your medical expenses were covered for that time? Of course not because what happens on year 41? Vehicle warranty is no different. Factory spec oil is often the McDonalds, and those operating temperatures are the chain smoking. 

  • Thanks 2
Posted
1 minute ago, OnTheReel said:

A tale of two TRXs.

 

Mine on mile 40 of a highway run in 90 deg heat. IMG_3931.thumb.jpeg.18a285ae2cd4d3ef67f266ee6e2f34d6.jpeg

Oil: 199 (Red Line 5w50 just installed)

Coolant: 185

ATF: 165

 

Meanwhile this is what most people think is OK:IMG_3933.thumb.jpeg.c2f7da326ce96472b7f502a41510fbf4.jpeg

ATF: 214

Coolant: 234

Oil: 286! (Factory approved 0w40, gotta save that warranty).

 

The fluid temps were well within allowed range. 286 may seem high but it was for a short period and is OK with fully synthetics. TRX has safety limits, which were beyond these temps.” 
 

What’s the safety limit? Punching a rod through the oil pan to add extra ventilation? 😂

 

We’re getting beyond blind faith in the OEs and into pure ignorance at this point.


I heard an analogy somewhere that I liked. Imagine your body had a full warranty for 40 years. Would you smoke 3 packs a day and eat only McDonalds because all your medical expenses were covered for that time? Of course not because what happens on year 41? Vehicle warranty is no different. Factory spec oil is often the McDonalds, and those operating temperatures are the chain smoking. 

That’s certainly compelling

Posted
22 minutes ago, OnTheReel said:

A tale of two TRXs.

 

Mine on mile 40 of a highway run in 90 deg heat. IMG_3931.thumb.jpeg.18a285ae2cd4d3ef67f266ee6e2f34d6.jpeg

Oil: 199 (Red Line 5w50 just installed)

Coolant: 185

ATF: 165

 

Meanwhile this is what most people think is OK:IMG_3933.thumb.jpeg.c2f7da326ce96472b7f502a41510fbf4.jpeg

ATF: 214

Coolant: 234

Oil: 286! (Factory approved 0w40, gotta save that warranty).

 

The fluid temps were well within allowed range. 286 may seem high but it was for a short period and is OK with fully synthetics. TRX has safety limits, which were beyond these temps.” 
 

What’s the safety limit? Punching a rod through the oil pan to add extra ventilation? 😂

 

We’re getting beyond blind faith in the OEs and into pure ignorance at this point.


I heard an analogy somewhere that I liked. Imagine your body had a full warranty for 40 years. Would you smoke 3 packs a day and eat only McDonalds because all your medical expenses were covered for that time? Of course not because what happens on year 41? Vehicle warranty is no different. Factory spec oil is often the McDonalds, and those operating temperatures are the chain smoking. 

 

 

Some observations there though. 

 

The second dash.  Tow/Haul is on which IMO implies that truck was towing and is spinning 3000rpm where your truck was 70mph, I assume not towing and in 8th at under 2000rpm.  

 

So two trucks in two different scenarios which would...have a sway in temperature readings.  

 

 

Posted
11 minutes ago, newdude said:

 

 

Some observations there though. 

 

The second dash.  Tow/Haul is on which IMO implies that truck was towing and is spinning 3000rpm where your truck was 70mph, I assume not towing and in 8th at under 2000rpm.  

 

So two trucks in two different scenarios which would...have a sway in temperature readings.  

 

 

Fair. But the point was more his nonchalant reaction (or really no reaction at all) to running those temperatures. It’s normalized, and even worse some people actually think it’s BETTER.

 

His truck still has the factory warranty using approved fluids, and stock thermostat & TBV. My truck doesn’t. Which one would you want to buy used?

  • Thanks 1
Posted
1 hour ago, newdude said:

 

 

Some observations there though. 

 

The second dash.  Tow/Haul is on which IMO implies that truck was towing and is spinning 3000rpm where your truck was 70mph, I assume not towing and in 8th at under 2000rpm.  

 

So two trucks in two different scenarios which would...have a sway in temperature readings.  

 

 

 

Again as true as that is what it shows is the truck is not set up for towing. @OnTheReel 's dash would be what it should look like towing as well. 

 

***************************************

General comments to attached to the newdude quote: 

 

 

Physics doesn't leave the room when it's towing or on track day. Thermostat doesn't do cooling, it does regulating. If the cooler is WAY to large for day in and day out task the thermostat keeps it warm enough. If the thermostat is defeated by a cooler to small then it needs enough cooler to put it in control. 

 

When I first bought Pepper my dash looked like #2 on a hot day doing 55 mph. Not quite that bad but you get the idea. I took steps to get to the OneTheReel dash look and it does quite well up to over 90 F air temps. Even with all the modifications I would need more to tow or run the Mexican deserts. 

 

GM gives us a 'starter kit' and a darn poor one at that. 

Posted
2 hours ago, OnTheReel said:

What’s the safety limit? Punching a rod through the oil pan to add extra ventilation? 😂

 

We’re getting beyond blind faith in the OEs and into pure ignorance at this point.

 

Somewhere we got the notion that getting away with something was the same as it not being a problem. Like the drunk who drives because he's to drunk to walk and because he never hits anything over a long span of time comes to believe that his behavior is harmless. If rods aren't hanging out, we're good, right? :crackup:

  • Like 1
Posted
2 hours ago, OnTheReel said:

A tale of two TRXs.

 

Mine on mile 40 of a highway run in 90 deg heat. IMG_3931.thumb.jpeg.18a285ae2cd4d3ef67f266ee6e2f34d6.jpeg

Oil: 199 (Red Line 5w50 just installed)

Coolant: 185

ATF: 165

 

I'm officially jealous. I can hit those numbers in that temperature, just not at 701 mph. I have work to do. 😉 

Posted
On 6/22/2025 at 5:25 AM, KARNUT said:

I’m an old guy. My memory is vivid from the 60s on. We had plenty of cars and trucks being a large family. Mostly GMs some Fords. Factually speaking. Even at 3K oil changes during that time. We without a doubt as a family and business. Have more vehicles passing mileage we’d only dream of back in the old days. It took me until recently to trust a vehicle passing 150K miles. That’s average for me now. I only recently stopped going extended with oil changes. Only because my driving changed. Sure there’s experimental engines that shorten engine life. As a rule generally the manufacturers that do it right have longevity. Even at their recommend extended drains. Simple buy those. But generally they all last longer than the old days. Well almost all. 

 

For sure. Hitting 188k on a fullsize pickup without engine or trans failure isn't exactly amazing. Was it the hundreds/thousands of hours of forum posts and obsessing over temperatures the magic potion? The guy who drives 40k per year and doesn't always change the oil on time but close enough, and when he does, tosses the keys to "Shop who uses bulk oil" seems to have about the same success rate overall.

 

...And if something major does break... fix it? Or buy a new one.

Posted
53 minutes ago, Grumpy Bear said:

 

I'm officially jealous. I can hit those numbers in that temperature, just not at 701 mph. I have work to do. 😉 

Truck has a ton of cooling from factory. They just made poor decisions to use it. I’d be running 205-215 coolant, oil and ATF when stock in the same conditions.
 

I pulled the OEM trans TBV and found it’s the same part number used on V6 Challengers and Chargers which was an odd choice. 1/2” lines and a big cooler don’t mean squat when you’re necked down to 1/4” at the outlet of the TBV. A TBV that is set to open way too late as well.IMG_3957.thumb.jpeg.1c2b3cc95bab48725a88a039cabad444.jpeg

  • Sad 1
Posted
1 hour ago, Atlas said:

 

For sure. Hitting 188k on a fullsize pickup without engine or trans failure isn't exactly amazing. Was it the hundreds/thousands of hours of forum posts and obsessing over temperatures the magic potion? The guy who drives 40k per year and doesn't always change the oil on time but close enough, and when he does, tosses the keys to "Shop who uses bulk oil" seems to have about the same success rate overall.

 

...And if something major does break... fix it? Or buy a new one.

The biggest change for us in the 80s was Amsoil. That was in engines, transmission and Hydraulic. Lower temperatures that led to higher working oil pressure and more tolerances to heat. We double the hours for oil changes with our equipment in the field. Our first test vehicle a 1988 7.3 with the C-6 transmission. After a transmission rebuild at 100K miles we added another 185K before we traded it in no other failures. The only change was Amsoil. At the same time we went extended on fluids per their instructions. Some people claim results with one or two vehicles. Our results are many years with many vehicles. Of course if you buy vehicles that are not well built you have to adjust to more frequent oil changes. I even have stopped going extreme extended. If I was running the interstate like I used to I would be going more extended. Most of the problems with the engines and transmissions today are build quality. Sometimes more frequent oil changes help that. I just buy vehicles that are more reliable. 

Posted (edited)
2 hours ago, Atlas said:

 

For sure. Hitting 188k on a fullsize pickup without engine or trans failure isn't exactly amazing. Was it the hundreds/thousands of hours of forum posts and obsessing over temperatures the magic potion? The guy who drives 40k per year and doesn't always change the oil on time but close enough, and when he does, tosses the keys to "Shop who uses bulk oil" seems to have about the same success rate overall.

 

...And if something major does break... fix it? Or buy a new one.

 

 Failure? That's your bar? :nonod:  Describe what success means to you.

 

Are you one of those people that thinks you can say a thing true? It is because you 'says' it is? 

 

Apples, oranges, it's all fruit, right? City dweller and OTR all the same pot of fish. 

 

As long as I've been here the goal post is always moving further along. Won't go 80K without using oil. It did. Won't go 100K without a lifter failure. It did. Trans wont make it past warranty. It did. Lifetime is 150K you sure, Yep. TSB on rings says you are on borrowed time. Catch can or die. It didn't. Still waiting for the cam/lifters/rings to fail. Still waiting for it to use oil. In fact I'm still waiting for deposits to form. (168K)

 

image.thumb.jpeg.a5892e80aa9ca969595c572462de83b5.jpeg

 

Open yours up and lets have a look at success. 

 

I replaced that piece of plastic around the starter. That's been my non-routine maintenance.

 

 

 

 

 

 

Edited by Grumpy Bear
Posted

It’s amazing how a bear comes out of his cave and preaches what everyone success should be. I’m happy with 200K and 20 years max. Some people it’s 10 years. That would be about 150K miles. I run my mower about 10 years. I usually run my appliances about 10 years. I don’t want drama and I can afford it. My kids will get plenty when I pass. All this talk about super high mileage. I have more high mileage vehicles than the bear. I’m normal with oil changes. My toy is a Acura Type R. G-4 I rather die. 

Posted
4 hours ago, Grumpy Bear said:

 

 Failure? That's your bar? :nonod:  Describe what success means to you.

 

Are you one of those people that thinks you can say a thing true? It is because you 'says' it is? 

 

Apples, oranges, it's all fruit, right? City dweller and OTR all the same pot of fish. 

 

As long as I've been here the goal post is always moving further along. Won't go 80K without using oil. It did. Won't go 100K without a lifter failure. It did. Trans wont make it past warranty. It did. Lifetime is 150K you sure, Yep. TSB on rings says you are on borrowed time. Catch can or die. It didn't. Still waiting for the cam/lifters/rings to fail. Still waiting for it to use oil. In fact I'm still waiting for deposits to form. (168K)

 

image.thumb.jpeg.a5892e80aa9ca969595c572462de83b5.jpeg

 

Open yours up and lets have a look at success. 

 

I replaced that piece of plastic around the starter. That's been my non-routine maintenance.

 

 

 

 

 

 

 

Mine has 213 miles. No reason to crack the valve covers.

 

Success for me is happiness. Very little to do with owning a truck or showing everyone how my top end is clean at 168k. I've seen and owned engines that have gone more miles and they're still clean. Some of them didn't even use synthetic for most of their miles. So I'm not really sure what your point is? A modern engine going 168k with regular changes is frankly...unremarkable.

  • Like 2
Posted
11 hours ago, Atlas said:

 

Mine has 213 miles. No reason to crack the valve covers.

 

Success for me is happiness. Very little to do with owning a truck or showing everyone how my top end is clean at 168k. I've seen and owned engines that have gone more miles and they're still clean. Some of them didn't even use synthetic for most of their miles. So I'm not really sure what your point is? A modern engine going 168k with regular changes is frankly...unremarkable.

👏

Posted

I happen to really like the fleet I have currently. And I modify and drive them hard. Success for me is having wear rates much lower than universal averages in spite of that. Simply by paying attention to many of the same things Grump preaches. You can dislike his delivery or just not care about your vehicles as much he does. But that doesn’t change what I’ve tested and observed on my own vehicles. 

  • Thanks 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • $3.90 to $4.50 depending on the brand and location of the station. 87 regular. 
    • Guys that read Dizzy's thread know that eons ago after multiple manifold pulls to clear the CCV orifice I converted it to a PCV system with an orifice below it via the valve cover. The blow-by (sticky rings) was so bad it was impossible to keep clean and accumulated water in the oil in the winter when the moisture would freeze in the fresh air side. The PCV functioning mainly as a check valve. I carefully sized the orifice to reproduce the factory values for crankcase pressure at idle.    Well...took a slug of oil to get my attention but the ring seal improvement meant the system was over drafting sucking oil up and out the breather. (V8 guys with orifice systems are nodding their heads). So today I choked it down...allot....to replicate the "just enough to hold a piece of paper on the fresh air side at idle". May still be to much but I'm working with shims at the moment. When I get it sorted I'll make a proper plate and plug. Perhaps using carburetor jets to tune it.    So I guess this means it isn't my imagination.    Dizzy is a pig guys so don't go expecting huge moves in equipment (your equipment) that is in much better shape. A needle valve....lord that just came to me....
    • I had a new engine installed with under 5,000 miles. It shut off coming around a residential street corner and wouldn't restart. Dealer indicated it seized. New one has been fine since with 10,000 miles on the replaced engine. Annoying but I was given a loaner for the 5 weeks it was down. I won't go with the 6.2l gasser so it's 3.0l again. I love the economy and it tows my enclosed car trailer just fine. 
    • Coming back from towing a car to my daughter in Nashville truck started making a screaming noise from underneath.  Pulled over placed in park and sure enough whining noise from underneath.  Dropped at the dealer fearing new tranny or another front pump/cover replacement.  Service writer said it sounded like the tranny too...  Well $300, new idler and a belt all is good.  Pop the hood and give a listen. lol  Now I'm telling dealers I'm no longer interested in a new truck.
    • HD uses the 6.6 gas.   Oil consumption while heavy working is considered normal.  1 quart per 100 gallons of fuel is the normal rate above 8600lbs GVWR.  If more than that, it is considered excessive.   They will have to perform an oil consumption test using the guidelines in TSB 03-06-01-023J.     Information on Engine Oil Consumption Guidelines All engines require oil to lubricate and protect the load bearing and internal moving parts from wear including cylinder walls, pistons, and piston rings. When a piston moves down its cylinder, a thin film of oil is left on the cylinder wall. During the combustion process, part of this oil layer is consumed. As a result, varying rates of oil consumption are accepted as normal in all engines. Oil Consumption Oil usage has a direct relationship with the amount of fuel used. The harder an engine works, the more fuel and oil it will use. Therefore, oil usage as a factor of fuel usage is a more accurate indicator of acceptable oil consumption levels than vehicle mileage for vehicles at or above 8600 GVW. The accepted rate of oil consumption for gasoline engines in vehicles at or above 8600 GVW is 1 liter (1 qt) within 400 liters (100 gallons) of fuel used. This rate only applies to vehicles under warranty, maintained in accordance with the appropriate maintenance schedule, driven at legal speeds and within design intent of the vehicle. Many factors can affect an owner's concern with oil consumption. Driving habits and vehicle maintenance vary from owner to owner. Thoroughly evaluate each case before deciding whether the vehicle in question has abnormal engine oil consumption. Gasket and External Leaks Inspect the oil pans, engine covers, and the engine oil cooler for leakage. Inspect for oil leakage into the engine coolant. Improper Reading of the Oil Level Indicator (Dipstick) The vehicle must be parked on a level surface to obtain accurate oil level readings. Verify that the dipstick tube is fully seated in the block. When checking the oil level, make sure the dipstick is wiped clean before taking an oil level reading and fully depress the dipstick until the shoulder bottoms out on the dipstick tube. The dipstick should be the proper part number for the engine/vehicle that is being checked. Not Waiting Long Enough After Running Engine to Check Oil Level The vehicle should be allowed to sit for at least 15 minutes, after the engine has been shut off, before taking an oil level reading to assure the oil has had enough time to drain back into the crankcase. In order to ensure accurate results, the temperature of the oil should be close to the same temperature as the last time the oil level was checked. Improper Oil Fill After an Oil Change Following an oil change, verify that the proper amount and type of oil was put in the engine and that the oil level on the dipstick is not above the full mark or below the add marks. Refer to the Owner's Manual or Service Manual for information on recommended oil quantity, viscosity, and quality. High Speed or High RPM Driving Continuous driving at high speeds/high RPMs may increase oil consumption. Because this may not always be an everyday occurrence, it is hard to determine exactly how much the oil economy will be affected. Towing or Heavy Usage Towing a trailer or hauling additional weight will increase oil consumption. Large frontal area trailers will further increase the work required from the engine, especially at highway speeds, and thus increases the rate of oil consumption. PTO Operation Operation of a PTO will increase fuel and oil usage, as the PTO driven accessory uses engine power to operate. Crankcase Ventilation System Verify that the positive crankcase ventilation (PCV) system is operating properly. Blockages, restrictions, or damage to the PCV system can result in increased oil use. Oil Dilution from Condensation On vehicles that are usually driven short distances, less than 8 km (5 mi), especially in colder weather, condensation generated from cold engine operation may not get hot enough to evaporate out of the oil. When this occurs, the dipstick may indicate that the oil level is over-full. Subsequent driving on a trip of sufficient length to enable normal engine operating temperature for 30 minutes or more, in order to vaporize excess moisture, may give the customer the impression of excessive oil consumption. Engine Temperature If an engine is run at overheated temperatures (see Owner's Manual or Service Manual) for more than brief periods, oil will oxidize at a faster than normal rate. In addition, gaskets may distort, piston rings may stick, and excessive wear may result. Verify that all cooling system components are in proper working order. Engine Wear Piston scuffing, excessive piston-to-wall clearance, tapered or out of round cylinders, worn, damaged or improperly installed valve guides, seals and piston rings will all cause an increase in oil consumption. Measurement of Oil Consumption Engines require a period of time to BREAK IN so that moving parts are properly seated. Therefore, oil economy should not be tested until the vehicle has accumulated at least 6400 km (4000 mi). An exception would be allowed only if an engine is reported to be using more than 0.946 liter (1 qt) in 1600 km (1000 mi).   Verify that the engine has no external leaks. Repair as necessary. Verify that the engine is at normal operating temperature (see Owner's Manual or Service Manual). Park the vehicle on a level surface. Wait at least 15 minutes, after the engine is shut off, before checking the oil level to make sure that most of the oil has had time to drain back into the crankcase. Check the oil level and record the vehicle mileage, date, and exact oil level on the form included in this bulletin. Next ensure the oil level is at, but not above, the full mark on the dipstick. add oil if necessary. Also ensure the proper viscosity and quality oil are being used as recommended in the Owner Manual Ask the customer once they have consumed 100 gallons of fuel schedule an appointment and return to the dealer for inspection. If the final evaluation shows that the engine uses more than 0.946 liter (1 qt) in 379 liters (100 gallons) of fuel used, follow the published symptom diagnostics as described in the appropriate Service Manual. If the oil consumption test shows that the engine uses less than 0.946 liter (1 qt) in 379 liters (100 gallons) of fuel used, explain to the customer that their engine meets the guidelines for oil consumption.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...