Jump to content

Rear leaf spring clunk

chris-i

By chris-i
in Troubleshooting & Recalls

 Share

Recommended Posts

chris-i Enthusiast

chris-i

Posted
Posted

I have a 2017 Sierra. There is a clunking in the rear end I've narrowed it down to the band clamps on the driver side leaf spring are loose so the leafs move and clunk when driving.

Anyone have the same issue?

Should warranty cover this or a TSB?

I'm in Canada if that makes a difference.

 

Thanks

 

Sent from my ELE-L04 using Tapatalk

 

 

L83_Z71 Enthusiast

L83_Z71

Posted
Posted

When is the "clunking" occurring? It wouldn't be when you're giving it gas and let off would it?

chris-i Enthusiast

chris-i

Posted
  • Author
Posted
When is the "clunking" occurring? It wouldn't be when you're giving it gas and let off would it?
No only when driving over bumps etc.

Sent from my ELE-L04 using Tapatalk

xMEATxHAMMERx Enthusiast

xMEATxHAMMERx

Posted
Posted

I also have a 2017 and get the same banging or clunking as you. There are 3 TSB's for this well known issue. First one says to clean and lube the leafs, second one says to tighten the U bolts, third is replacement. I'm currently waiting for both sets of leaf springs to arrive for my truck that has the high mileage of 15k.

chris-i Enthusiast

chris-i

Posted
  • Author
Posted
I also have a 2017 and get the same banging or clunking as you. There are 3 TSB's for this well known issue. First one says to clean and lube the leafs, second one says to tighten the U bolts, third is replacement. I'm currently waiting for both sets of leaf springs to arrive for my truck that has the high mileage of 15k.
How many times have you had your truck in for this issue for them to agree to replacement?
I'm bringing mine in to the dealer for the first time, but I am not going to keep going back either they replace them the first time or I'm going to a spring shop and I'll pay to have have it fixed.

Sent from my ELE-L04 using Tapatalk

chris-i Enthusiast

chris-i

Posted
  • Author
Posted
Twice... I had to take a mechanic for a ride the second time. 
Ok thanks for the information.

Sent from my ELE-L04 using Tapatalk

Baytrucker Enthusiast

Baytrucker

Posted
Posted

I have this issue too. I'm pretty sure anyone with a 1500 who gets their truck dirty has this issue. Its a design issue with the OEM leaf springs. Fleet truck owners don't really care if the truck makes noise, so neither does GM since fleet trucks consist of most of their sales. The only people buying GM half-tonnes privately are the poor folks (like me) who haven't figured out that GM is not even remotely close to the same company they were 15 years ago.

 

The noise is caused by dirt getting in between your leaf springs. Its like this in all the K2 series trucks. There is no permanent solution other than to replace the springs with aftermarket.

 

Some folks are just power-washing the springs on a regular basis. Others are sticking rubber sheets or bicycle tire inner-tube chunks between the leafs. Some have had luck with aftermarket silicone lube spray. A lot of folks just live with it.

 

The TSB that GM has is a low-cost band-aid to get you to go away until the warranty expires. The noise will always come back. In the 2019s, GM replaced the leaf springs with springs made from composite, finally catching up to what Ford and Ram started doing in the mid 2000's.

 

For the K2 series, they have your money already so they don't care.

 

If it bothers you, and you can't afford aftermarket springs, something like this is your best solution.

 

 

chris-i Enthusiast

chris-i

Posted
  • Author
Posted

So got the truck back from the dealer they of course cleaned and greased between leafs. And they changed the insulator pads between all the leafs. Driving home there is no clunking so we will see only time will tell. The manager also said if the clunking returns they will change both leaf sets under warranty. Hopefully he keeps his word.

Sent from my ELE-L04 using Tapatalk

Mdhunter63 New Member

Mdhunter63

Posted
Posted

I have same issues with leaf springs 2018 silverado 1500 4x4. Dealer retorqued bolts and lubricated springs, didnt work. Next installed new inserts but didnt work. Now there ordering new leaf springs. See if it works.

Z45 Senior Enthusiast

Z45

Posted
Posted

2017 1500 Sierra 26,000 miles.  Heading into my 3rd winter driving on salt covered road and no spring noise.

Mozzer Enthusiast

Mozzer

Posted
Posted

Mine were changed four years ago under warranty, just started squeaking / creaking again so I guess I was lucky.

Sent using Tapatalk - 2014 5.3 WT

Eddie 70 Senior Enthusiast

Eddie 70

Posted
Posted

My 2014 was doing it and I did the rubber pads and bicycle inner tube fix. Been quite as a field mouse since.

large.20190914_100944.jpg.9954d944c572ff29c8d7ad7bf6573acc.jpg
 

truckguy82 Senior Enthusiast

truckguy82

Posted
Posted
On 9/28/2019 at 9:37 PM, Eddie 70 said:

My 2014 was doing it and I did the rubber pads and bicycle inner tube fix. Been quite as a field mouse since.

large.20190914_100944.jpg.9954d944c572ff29c8d7ad7bf6573acc.jpg
 

How did you install? Did you take apart the springs to install that or simply jack up the truck and shove it in there?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  
    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...