Jump to content

Trailer camera issues

In2racn
 Share

Recommended Posts

In2racn Enthusiast

In2racn

Posted
Posted

I purchased the trailer camera (#657) for my 2020 Denali 3500. I installed it on my 7 x 16 V nose trailer. The rear trailer camera view really is nice. However, not that it is a big deal, but the transparent trailer setting is not working properly. I have tried a couple setups.  

 

My trailer is 7' inside height and the overall height ground to roof is 100 inches. When I aim the camera down to get the base of the ramp door, I still get a good long distance of rear view as well. The range of the camera is such that I can see the very bottom back of the trailer at the lower portion of the screen and still the top inch of the screen is the sky horizon. However, at that angle, even after I have entered all the trailer dimensions in the setup, the system does not calibrate for the transparent feature. 

When I tilt the camera up, the system tries to calibrate, but I end up with a weird split screen that "kinda" looks like the transparent views advertised by GM, but my trailer is not transparent. Check out the picture in the link;

 

Non-transparent trailer mode.

 

Anyone having any luck with the mode? Tricks, tips?

 

Thanks.

  • Replies 94
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

In2racn
In2racn

Shotgun,   I agree, the key with these cameras is the awesome ability to see behind your trailer. It is really a cool option to have that functionality integrated in. The transparent thing i

MTU Alum
MTU Alum

I usually backup to trailer and get aligned to trailer hookup, shut truck off, hook up trailer and chains, then plug in electrical, and finally camera.  These cameras don't like a hot hookup where the

ShotgunZ71
ShotgunZ71

You can put them on 5th wheels, you just won't have the transparent trailer view. However, the view with the mirror cameras and rear vision camera is pretty dang good.

Posted Images

sdelam Enthusiast

sdelam

Posted
Posted

posted by another memeber (MTU Alum);

 

"There are proper placement and camera angle that need to be followed.  The camera needs to be in center of trailer and 4 inches higher than camera in tailgate when your trailer is attached.

 

The camera angle needs to be about 35 degrees.  So 0 degrees would be straight down, raise the camera 35 degrees from there.  You generally don't want to be seeing the end of trailer or bumper.

 

If you see any shadows in the rear trailer camera view, it will have trouble calibrating.  You may have go in different direction.  

 

I recommend exiting the trailer app when calibrating and open camera app and select transparent view.  There will be a yellow status bar on the bottom to show the calibration progress.  I have never seen them calibrate in 60 feet it usually quite a bit longer."

MTU Alum Enthusiast

MTU Alum

Posted
Posted

In order to calibrate, you need to drive in straight line from 10 to 30 mph.  If you have a v nosed trailer you probably need to adjust your center of ball to front of trailer measurement.  The measurement should be from center of ball to if the trailer had a flat front.  So measurement should be center of ball to where the v starts on the trailer.  

 

The transparent image works by stitching four camera views together: tailgate, outside mirrors, and trailer cam.  

 

#iworkforGM 

ShotgunZ71 Senior Enthusiast

ShotgunZ71

Posted
Posted

I wonder if anyone with a long 5er or gooseneck tried to manipulate the numbers and style of camera to get this to work, or at least semi-work? I know that any 5th wheel is ineligible to have it, so you'd have to select a type of tag-along trailer and pretty much max out the dimensions. I installed the rear trailer camera and was happy just to see behind the camper, then noticed there is a view that shows the mirror cameras and rear trailer camera on one screen. That's pretty nice, especially when backing.

In2racn Enthusiast

In2racn

Posted
  • Author
Posted

Shotgun,

 

I agree, the key with these cameras is the awesome ability to see behind your trailer. It is really a cool option to have that functionality integrated in. The transparent thing is really no big deal for me, but like a kid with a new toy, you just wanna play with the cool factor.

 

In a different thread, MTU Alum, who works for GM, explained to me that in order for the 4 cameras to stitch the transparent view, the trailer camera needs in a position slightly above the tailgate camera. That parameter practically rules out the transparent view on a tall enclosed trailer or certainly on your 5th wheel camper. 

 

On my wishlist for GM is the ability to put the rear trailer cam view ON the rear-view mirror screen. We are trained to look at the rear view mirror to see behind us, if we have a trailer camera, we should have the option to cast that onto the rear view mirror screen. That would free u the main screen for other functions.

  • Like 2
ShotgunZ71 Senior Enthusiast

ShotgunZ71

Posted
Posted
2 hours ago, MoCOgmc said:

Wait, why can't we put them on 5th wheels? 

You can put them on 5th wheels, you just won't have the transparent trailer view. However, the view with the mirror cameras and rear vision camera is pretty dang good.

  • Like 1
In2racn Enthusiast

In2racn

Posted
  • Author
Posted
2 hours ago, ShotgunZ71 said:

You can put them on 5th wheels, you just won't have the transparent trailer view. However, the view with the mirror cameras and rear vision camera is pretty dang good.

I agree.... super cool to have this. 

ShotgunZ71 Senior Enthusiast

ShotgunZ71

Posted
Posted

Been using my on my 5th wheel and it's been great...until today. Got home and went to use the camera to get backed up correctly and got nothing but a black screen. The infotainment lets me select it, but it shows no picture. I've changed ports to the in-trailer view and got the same result. One time we did get a picture blip, but nothing consistent. Any ideas or similar issues?

In2racn Enthusiast

In2racn

Posted
  • Author
Posted
8 hours ago, ShotgunZ71 said:

Been using my on my 5th wheel and it's been great...until today. Got home and went to use the camera to get backed up correctly and got nothing but a black screen. The infotainment lets me select it, but it shows no picture. I've changed ports to the in-trailer view and got the same result. One time we did get a picture blip, but nothing consistent. Any ideas or similar issues?

That sucks... we paid way too much money for these cameras for them not to work for years and years.

 

ShotgunZ71 Senior Enthusiast

ShotgunZ71

Posted
Posted
7 hours ago, In2racn said:

That sucks... we paid way too much money for these cameras for them not to work for years and years.

 

I'm going to check the back of the connection on the truck to see if something is loose. It's like it knows there is a camera there, but no picture. The one time we got a picture after we got home, I went a shook the cable, wiggled it, etc to see of that was the issue but it stayed on until we unplugged and plugged back in. Odd, for sure.

ShotgunZ71 Senior Enthusiast

ShotgunZ71

Posted
Posted

Messed with it some this afternoon. Never got it to work on the rear trailer mode/plug, but did get it to work briefly when plugged into the interior trailer plug. While it was on, I pulled, shook, and flexed the plug and wire. The picture stayed on. I unplugged it and plugged it back in and it wouldn’t come on that time. It’s almost as if it’s a power issue with the truck plugs or the ECM isn’t sending power to the camera all the time. Anyone know how the power is supplied to these trailer cameras?

MTU Alum Enthusiast

MTU Alum

Posted
Posted

Do you have the seven way trailer plugged in when checking the trailer cams?  I know you will not get power without 7 way plugged in.  Also, I recommend having the truck completely asleep before plugging trailer cams.  The truck is usually asleep after the green OnStar light goes out.

 

#iworkforGM 

ShotgunZ71 Senior Enthusiast

ShotgunZ71

Posted
Posted
3 hours ago, MTU Alum said:

Do you have the seven way trailer plugged in when checking the trailer cams?  I know you will not get power without 7 way plugged in.  Also, I recommend having the truck completely asleep before plugging trailer cams.  The truck is usually asleep after the green OnStar light goes out.

 

#iworkforGM 

I will try that! Thanks for the tip. Will let you know how it goes. So, basically have the truck off, then connect the 2 cables, then start the truck? May even try some contact cleaner on the connections to make sure nothing got in them.

MTU Alum Enthusiast

MTU Alum

Posted
Posted

I usually backup to trailer and get aligned to trailer hookup, shut truck off, hook up trailer and chains, then plug in electrical, and finally camera.  These cameras don't like a hot hookup where the truck is running or communications bus is alive.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I had skimmed through that article when you posted the link and honestly I felt rather defeated in a sense and realized that all these years in changing oil that in fact putting in what I was told was a good quality oil was probably not filtered as well as it should be although the filter put on the engine would be what ( as long as it never went into bypass mode ) would be the final filtering of the new oil that the engine components would first see, but then the filtering media itself is not up to par to what is ideal because a full flow filter would be too restrictive to filter fine enough for the engines best outcome in the long run. Only one of our tractors over the years which was a Versatile with a 855 Cummins had a separate bypass filter, some engine manufacturers did spec a partial bypass system within the main oil filter but I don't believe any other trucks or equipment I was servicing used such a filter. No doubt a product like the Amsoil bypass system is of benefit as long as nothing goes sideways with the extra plumbing and filter such as a rupture/leak that could cause the oil to pump out of the engine ( yes that Versatile had a remote canister with hoses routed to it as well ). With the idiot egr system on a diesel and as a result forcing a lot more soot into the oil, that certainly isn't helping the diesel engines cause or as you pointed out the GDI engine issue with creating more soot and aside from having a fancy secondary filtering system, changing the oil more often helping lower the total soot load.     So oil manufacturing and the end product is not something one can control and I wonder if there are specs on what various oil packaging companies produce in particle count or size. As to the filtering, if the OEM is not designing a filter size and spec that is really what it could be, they too are short changing the end user and so what is the answer. Of course as you say the oil side can only do so much if the air side isn't keeping up its end of the picture and air filters are only so efficient and if in a dusty environment such as farm or construction or driving gravel roads there is a lot of dirt to filter out and some of that ends up into the air stream.    Of course the irony in places like where I am where they dump the salt on the highways but also will mix in some calcium or outright pure calcium for problem road area's, or using calcium as dust control on gravel roads, the vehicle that gets used in that environment may rust out before a properly engineered engine and maintenance finally wears out so one has to face that reality in the rust belt. 
    • GAMark
      Road Master Active Suspension

      By GAMark · Posted

      Has anyone run these on their 2500?
    • Erfar
      Oil Change

      By Erfar · Posted

      have you stuck with dealer oil changes since then? I made the same switch after getting tired of crawling around under the truck, but I’ve found some dealers are way better than others about getting you in quickly. Curious if yours has been good about scheduling or if you’ve had to look elsewhere for quicker turnaround.
    • cherryred21duramax
      Can anyone decode a VIN to determine if this truck has had emissions issues or a recall?

      By cherryred21duramax · Posted

      Thank you.   I am set on a 3.0 Duramax as my previous truck with a Ford Ecoboost had just as many, if not more, "common" issues.  Cam phasers, timing chain issues, 10-speed valve body and CDF drum, emissions issues, etc.  So I figured, why not get 2x the fuel mileage (these things got 27+mpg on every mixed city/highway test drive I put them through) and better towing capability with resale value to boot?   My minimum, shortest trip will be 50 miles 1-way and I regularly go out of state with a travel trailer.  I'm planning on using this for a marketing/event promotion business also, which would require regular towing of trailers for bands, DJs, sound and lighting gear, along with my personal camera gear for filming events.   Looked at other trucks in the $30k+ price range but the issues seem to be everywhere, plus too many with gaudy mods.  I'm literally sticking with RWD trucks because they tend to be actually used as trucks, vs. the 4x4 models I've seen with unsafe lifts, huge tires, and general mods that would affect reliability (I'm wondering if some of them were tuned, hence the aggressive throttle response and hard shifting).   So my goal is to find a stock, 3.0 with 1 or 2 owners, in good physical condition, and decently well maintained.  Can't seem to find that up here, everything in the $27-30k range has had multiple owners, smoke smell, issues, or body damage.  Or the ridiculously modified trucks with 80k miles for under $27k but lots of problems...
    • KARNUT
      OCI, not when but why?

      By KARNUT · Posted

      That’s pretty tough Grumpy. I reread the previous few posts. They all reference oil changes. Much like your last thread. In my humble opinion it keeps things interesting.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...