2019 custom mods.

Flatblack83 · April 25, 2020

Ordered a set of trailboss replica 20X9's, gloss black with silver bowtie center cap and black lugnuts. Should see them late next week.

Goobax · May 2, 2020

On 3/5/2020 at 7:07 PM, Flatblack83 said:

New headlights, billet grill...night view

How far down did you have to take apart the front end for the headlight swap? Was it just the grill and lights that had to be removed or was there fender/bumper involvement? Hoping to do the swap this upcoming weekend. Also where did you mount the load resistors for the gen5DIY harness?

Thanks!!

Flatblack83 · May 2, 2020

3 minutes ago, Goobax said:

How far down did you have to take apart the front end for the headlight swap? Was it just the grill and lights that had to be removed or was there fender/bumper involvement? Hoping to do the swap this upcoming weekend. Also where did you mount the load resistors for the gen5DIY harness?

Thanks!!

Besides the grill the fender wings need to come off to get the headlights out. For the load resistors there's holes in the fender behind the light that i used with small bolts. They are in there just enough that u can only see them if your really looking for them.

Just take your time, the front of the trucks alot of plastic clips and a few bolts. Do make sure your lights work before putting it all back together.

Goobax · May 2, 2020

1 minute ago, Flatblack83 said:

Besides the grill the fender wings need to come off to get the headlights out. For the load resistors there's holes in the fender behind the light that i used with small bolts. They are in there just enough that u can only see them if your really looking for them.

Just take your time, the front of the trucks alot of plastic clips and a few bolts. Do make sure your lights work before putting it all back together.

Sounds good thanks!

Flatblack83 · May 3, 2020

Color matched, can u tell they are covers..?

Edited May 3, 2020 by Flatblack83

Flatblack83 · May 3, 2020

T1dan · May 3, 2020

Bad ass truck man. I’m going to do that headlight conversion. I believe they have been able to keep the custom grill using the Lt/Ltz headlights.

Flatblack83 · May 3, 2020

1 hour ago, T1dan said:

Bad ass truck man. I’m going to do that headlight conversion. I believe they have been able to keep the custom grill using the Lt/Ltz headlights.

Thankyou.

Not 100% on the grill but it would take mods or spacers etc. They aren't shaped the same on the ends. The custom doesn't have the drl like the lt/ltz.

2024Denali · May 3, 2020

On 4/25/2020 at 6:10 PM, Flatblack83 said:

Ordered a set of trailboss replica 20X9's, gloss black with silver bowtie center cap and black lugnuts. Should see them late next week.

Where did you order these?

Flatblack83 · May 3, 2020

Just now, 2020SilveradoCC said:

Where did you order these?

Ebay, actually. From a place in Florida, they order em and they come right from California. Sent right from factory reproductions.

2019Custom · May 3, 2020

On 12/27/2019 at 6:36 PM, Flatblack83 said:

The readylift just didnt see like it was enough after seeing the 3-3.5 lifts. I purchased a stage 1 icon lift with the coilovers set at 3 inch and a rear 1.5 block with shocks. Plus I used a set of rough country control arms.

Did you get the rear blocks as part of the kit or separate? Looking for somewhere that just sells the rear blocks standalone

2019Custom · May 3, 2020

On 1/15/2020 at 6:26 PM, Flatblack83 said:

All cleaned up, ready 4 Saturdays snow fall. Heres the newest if the stance with the side steps.

Are you happy with the sidesteps? They look awesome. Assume it was an easy install?

2019Custom · May 3, 2020

On 2/9/2020 at 1:27 PM, jtlans said:

I have a 2020 Custom that I have done a few things to. A before and after comparison is attached.

Did you do the mirrors and handles yourself? Have watched a bunch of videos on both and it looks a little risky as to whether you come out okay doing them yourself

Flatblack83 · May 3, 2020

1 hour ago, 2019Custom said:

Are you happy with the sidesteps? They look awesome. Assume it was an easy install?

Yea they are very nice , super easy to do. Direct bolt on, threaded holes are ready in the cab.

Flatblack83 · May 3, 2020

1 hour ago, 2019Custom said:

Did you get the rear blocks as part of the kit or separate? Looking for somewhere that just sells the rear blocks standalone

I bought a kit from ebay, it was 1.5 blocks and ubolts 80.00