Forward collision and lane keep assist still a problem on 2022 refresh?

[Kaylan Steen]

Oh dang, mine went out again, so I pulled the fuse and waited a couple minutes. It was still working today. I'm just going to continue pulling the fuse until GM does thr recall for it.

[Jason Holder]

@Kaylan Steen Can you tell me what fuse you pulled, I was trying to figure that out to give that a try, Thanks!

[Manny Man]

2 hours ago, Jason Holder said:

@Kaylan Steen Can you tell me what fuse you pulled, I was trying to figure that out to give that a try, Thanks!

 

[Kaylan Steen]

It'd thr 10 amp second from the left at #11 like the picture shoes. I pulled it and could see thr marks on the pins. It had been pulled a couple times previous. It was very quick and easy.

[Steve Di Piano]

Just adding to the pile. EAB, lane assist and Auto Start/Stop appears to no longer be working. Dealer tomorrow.

[Kaylan Steen]

I wouldn't waste my time with them. Pull the #11 bank fuse and wait a few minutes and put it back in. If it still doesn't work, take it in. It's a 10 amp fuse in the upper left of the box on the passenger side. Good luck!

[Jason Holder]

@Kaylan Steen, Thanks I will give that a try

[Manny Man]

Got a call from the dealership, they found a camera module and they overnight it, should have it tomorrow. 
I’m impressed with the customer service so far. They told me if it gets there early enough they might be able to squeeze me in same day, Will update soon…

[Kaylan Steen]

Good luck! I've not had any issues since I bent one of the spades a little to make it a tighter fit. 

[JGoose11]

Same issue with my 2022 Trail Boss as well. Auto stop quit working first then front collision alert/adaptive cruise/lane assist. Have service appt on Monday. Pulling fuse resolved issue temporarily? 
Thanks for the advice 

[Manny Man]

Just now, JGoose11 said:

Same issue with my 2022 Trail Boss as well. Auto stop quit working first then front collision alert/adaptive cruise/lane assist. Have service appt on Monday. Pulling fuse resolved issue temporarily? 
Thanks for the advice 

Yes. Pulling the fuse will solve it temporarily.

[Manny Man]

UPDATE:

Camera module arrived. Dropped the truck off at the dealership.

Got a call 6 hours later saying they have bad news, same issue, even after replacing and programming the module. They told me to drop it off again on Monday so they can reach out to GM-engineering, maybe they can solve it with over the air diag...

I will keep you guys posted.

Edited July 10, 2022 by Manny Man

[Kaylan Steen]

This is my theory on this issue. The fuse box is out of its tolerance specs, so the fuse is loose. I took the fuse and slightly bent the spades just enough to keep the fuse tight in the box. I've not had an issue at all since doing that. I also just got back from a small strip out of town and didn't have an issue. So, I might be onto something with the tolerances being off within the fuse box itself. Time will tell!

[Manny Man]

Just now, Kaylan Steen said:

This is my theory on this issue. The fuse box is out of its tolerance specs, so the fuse is loose. I took the fuse and slightly bent the spades just enough to keep the fuse tight in the box. I've not had an issue at all since doing that. I also just got back from a small strip out of town and didn't have an issue. So, I might be onto something with the tolerances being off within the fuse box itself. Time will tell!

No sir, this can't be it. It takes time for it to happen again so I can 100% guarantee, you'll have this issue again.

I think it's something with the software messing up the module...

[6.2ZR2]

Did they replace the collision alert camera?

That is what fixed mine, the unit up in the mirror.