Jump to content

Battery level

devildog2621
 Share

Recommended Posts

devildog2621 Enthusiast

devildog2621

Posted
Posted

Threw charger on my battery today. Batteries less than a year old. The charger said The battery was at 40%. What would be the cause of a low battery? Don't believe it's a drain. GMC Sierra 1500 2013.

dsr611 Senior Enthusiast

dsr611

Posted
Posted

Dead cell, bad alternator, parasitic draw from somewhere, battery could have been bad to begin with

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

These trucks have a smart charging system, the computer will determine what voltage the alternator needs to charge at.

 

So it can be anywhere from 13 volts up to 15 volts depending on the demand of the computer.

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted (edited)
21 hours ago, Matthew J M Devildog Thompson said:

Threw charger on my battery today. Batteries less than a year old. The charger said The battery was at 40%. What would be the cause of a low battery? Don't believe it's a drain. GMC Sierra 1500 2013.

If the truck is sitting for a few days and then you make some short runs the battery never gets a chance to become fully recharged.  The computer system typically keeps the battery at a state of charge in the 70-80 percent range to maximize its life.  A battery being jammed to 100% all the time does not last long.

 

GMs replacement spec is 64%, a battery that cannot maintain a state of charge at that number (12 hours after charging) is out of spec and ought to be replaced.

 

If she does sit for periods of time, put a tender on it.  This will also de-sulfate the plates and allow the battery to take a "full" charge again.  I got another year out of a battery by doing this once.

 

This generation of trucks were not designed to charge AGM batteries.  They won't last as long as they could have.  Just read a caveat in my shop manual, it says an AGM can be damaged if charged to more than 14.5 volts.  Our system can charge at 15.5v if the computer decides to.

Edited by swathdiver
devildog2621 Enthusiast

devildog2621

Posted
  • Author
Posted

Thank you for that information. I do have an AGM battery. I have a voltmeter on the dash and it never reads more than 14.4. I didn't realize they only maintain a 70 to 80% charge. And it will sit for 3 days and then I'll make a short trip less than 5 mi , then it'll sit a couple more days.

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted
On 4/28/2023 at 8:18 AM, Matthew J M Devildog Thompson said:

Thank you for that information. I do have an AGM battery. I have a voltmeter on the dash and it never reads more than 14.4. I didn't realize they only maintain a 70 to 80% charge. And it will sit for 3 days and then I'll make a short trip less than 5 mi , then it'll sit a couple more days.

Take her out for a highway run once a week and or put her on a battery tender.

  • Like 1
diyer2 Senior Enthusiast

diyer2

Posted
Posted

My 2cents. it sits 2-3 days with the power draw for the computers. Then a short trip with running lights, radio, heater on. Not enough time to charge the battery, battery tender is a must.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,399 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed, regardless of whether they are in warranty or not, or in the hands of the original owner or not. Why not updates as well, especially since some of those can be safety related also?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...