Jump to content

Home made wood ramps

Interleukin6
 Share

Recommended Posts

Interleukin6 Enthusiast

Interleukin6

Posted
Posted (edited)

I am using homemade 6-inch tall wood ramps (2x10 pressure-treated lumbar from Home Depot) for oil change because mine is LT (no factory or aftermarket lift) which barely gives me space to crawl underneath the truck. I ended up making these after reading many bad reviews about plastic and even steel ramps. Just want to make sure these woods are strong enough to lift our trucks? Is putting some Jack stands with them overkill or good for backup? What system(?) are you guys using to lift Silverado for self-maintenance? Also, can anyone recommend a decent bottle jack that I can use for CR-V with the ground clearance of 6.7 inches as well? Thank you.

Edited by Interleukin6
  • Like 1
redwngr Senior Enthusiast

redwngr

Posted
Posted

When I was using wooden ramps they were similar to these.

The steps on mine were shorter -- but longer steps should let the ramps work for vehicles that have lower approach heights.

 

See related image detail. Homemade Car Ramps - HomemadeTools.net

 

I did NOT bevel the ends of each board like these (and they worked fine without the bevel)

 

Zero concern about strength since the boards are flat on top of each other. 

 

 

I'd get a hydraulic floor jack and jack stands instead of a bottle jack for the CR-V.

 

Might be able to find one that will lift the truck too -- and then lower truck onto jack stands before getting under it. 

 

Ramps can be a nuisance to crawl around gain access under the truck. 

 

 

If you want to do tire rotation at oil change time ramps aren't gonna work.

 

  • Like 2
Bikerjon Enthusiast

Bikerjon

Posted
Posted

redwngr is right. First of all always use jack stands any time you are underneath a vehicle. This is not overkill. You really should get yourself a proper hydraulic floor jack and jack stands. They wll pay for themselves if you are doing your own oil changes or other service work. 

  • Like 1
jaxcam02 Enthusiast

jaxcam02

Posted
Posted (edited)

For oil changes I have no problem using my plastic rhino ramps I had had for years, still always place jack stands on the frame or k member. 

For all other work which requires wheels off the ground. Go buy yourself a high lift hydralic floor jack. The best jackstands on the planet are the esco flat tops with rubber pads. https://esco.net/product/3-ton-performance-jack-stand-pair/

Edited by jaxcam02
  • Thanks 1
repairman54 Enthusiast

repairman54

Posted
Posted

2x on the Rino ramps. The 10k rated ones. Been using them for years on my old Yukon and Tahoe and no issues on the first oil change on my Silverado. Safe and secure. Put it in 4 low and all the trucks just creeped right up on them. 

  • Like 1
Silverado4x4 Senior Enthusiast

Silverado4x4

Posted
Posted

I have the plastic Rino ramps also they work great and can stack them together plus their light and store easy. 

 

I never used jack stands yup I was dumb until I was changing the brakes on my father-in-laws truck years ago and had it jacked up with a hydraulic jack doing the front and all the sudden the truck drop all the way down slowly and that woke me up, went out and bought a new jack and jack stands. But I did use a brick if I had to get under the vehicle before but not anymore jack stands from here on out.

diyer2 Senior Enthusiast

diyer2

Posted
Posted

I built wooden ramps for our Hyundai oil changes, I know they won't fail. Floor jack and stands for other work. 

redwngr Senior Enthusiast

redwngr

Posted
Posted

Bricks and concrete blocks can decide to 'crumble' or crush. 

They are not a substitute for jack stands or solid hardwood blocking. 

  • Like 2
repairman54 Enthusiast

repairman54

Posted
Posted
21 hours ago, Silverado4x4 said:

I have the plastic Rino ramps also they work great and can stack them together plus their light and store easy. 

 

I never used jack stands yup I was dumb until I was changing the brakes on my father-in-laws truck years ago and had it jacked up with a hydraulic jack doing the front and all the sudden the truck drop all the way down slowly and that woke me up, went out and bought a new jack and jack stands. But I did use a brick if I had to get under the vehicle before but not anymore jack stands from here on out.

2x crap happens. I have an old friend who had to jack a car off his father when a jack failed, and it dropped on him. 

Sadly his father did not make it. 

Always use a jack stand, it only takes a minute to toss one in there. 

KARNUT Senior Enthusiast

KARNUT

Posted
Posted

The only time I use ramps was for oil changes and at home. I always had access to a shop that had heavy duty jacks and stands.  Being my whole family was (is) car enthusiast we usually would work on toys together. As far as any vehicle falling off a stand if a tire was off a vehicle it was under the vehicle too. I did have one vehicle fall off ramps as I was driving up. I caught the edge, my fault. Never used them again. I saw it as a sign. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      MPG at 600 miles

      By Chuck FB · Posted

      I would have to read back to get a better picture in my mind of some of the other comments and what they were using for a driving scenario they based the fuel mileage off of. That is why the fuel mileage conversation is extremely difficult to make fair comparisons from. If I was to be living in town and only driving around town, light to light and some longer stretches that doesn't have a light every block, and the usual stop at a grocery store and the bank and so on and so forth, my fuel mileage even during the summer time would be so bad with my truck I don't even want to know how bad it would be !. Then add in winter time and idling to warm it up to clear the windows and driving through snowy streets etc, large heavy trucks with gas engines have NEVER been worth crap for fuel mileage and why some little pot licker of a car with wheelbarrow tires and a 1300 cc four cylinder non turbo engine was the ticket to using a mere fraction of the fuel over a full size pickup.    By the way my truck has the 34" tires as its a HC but not the BFG KO3 tires ( that was an option for my truck but the sales guy couldn't figure out what the tires actually were so that never got on the order until it was too late to change the truck order ). So what fuel mileage your getting actually sounds good for "town driving" and with my truck when I go to town the fuel mileage keeps increasing as I get closer to town because it takes quite a while to get the driveline oils warmed up ( and why it always shows better fuel mileage on the return trip from town because its already warmed up ) but once I am in town that fuel mileage average just keeps dropping the more I mess around town and then has to recover back to something reasonable again by the time I get home for an over all average.    I'd be curious what your sticker says for the factory weight of your truck, mine is close around that 7700 lb due to the options it has. But anyway the long and short is, vehicle weight, higher rolling resistance heavy tires and a hefty driveline and a relatively large gas engine make for crap fuel mileage in stop and go scenarios, all one can do is drive it easy off the line at each stop and as my dad had said over the years, drive like a raw egg is under your foot and that's the best one can do. Years back with a carbed engine and if the carb was getting a bit out of tune etc as would the ignition system, the fuel mileage on pickups with larger engines was just awful compared to what your getting. We pay the fuel price penalty for driving HD trucks over some little vehicle, that is the reality. 
    • diyer2
      Navigating senior years.

      By diyer2 · Posted

      Speedy recovery.
    • KARNUT
      Slate Electric Truck

      By KARNUT · Posted

      We had two Toyota’s with that engine in the mid 80s. We had 50 gallon fuel tanks, a toolbox full of tools, an air compressor and assorted parts for our equipment. We beat those up and down pipeline ROWs until we started buying diesel trucks. Then they became parts runners and first vehicles for our teenagers first cars. Our shop Forman wrecked them both two years apart when we hired him out of high school as an apprentice. Good thing he’s an excellent mechanic. It took awhile before he could be called a good driver.
    • diyer2
      Gas Prices

      By diyer2 · Posted

      $4.26 85 oct 
    • William Aldrich
      Bent valve in 2025 GMC Canyon Denali - Requires engine swap at 14K miles

      By William Aldrich · Posted

      I have a 2025 GMC Canyon Denali.   On a trip recently the engine failed.  The dealership diagnosed a bent valve and says there is a service bulletin that indicates to 'relace the engine'.  The truck only has about 14K miles and is under warranty.   The failure occurred 5/11/2026.   So far I have worked with GM Customer Assistance and Roadside Assistance.  Evidently no engines are available and nobody will offer a date when a new one will be.   Coming up on two months with no repair or timeline and no loaner from the dealership.   GMC Customer Assistance is 'ghosting' me and keeps closing the cases I've opened with no resolution.   Hoping someone can help me on how to escalate this issue.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...