Jump to content

2024 Silverado 1500 oil leak

Sheryldk
 Share

Recommended Posts

Sheryldk New Member

Sheryldk

Posted
Posted

I have a 2024 Chevy Silverado 1500 with 411 miles on it. Noticed yesterday and today two oil spots. Appt tomorrow with dealership. Anyone having same problem?

Bikerjon Enthusiast

Bikerjon

Posted
Posted
1 hour ago, Sheryldk said:

I have a 2024 Chevy Silverado 1500 with 411 miles on it. Noticed yesterday and today two oil spots. Appt tomorrow with dealership. Anyone having same problem?

No problems with mine. 5.3 w 26xx miles.

TrueBlue Enthusiast

TrueBlue

Posted
Posted

Which motor? My 2023 LT 2.7T developed an oil pan leak at 700 miles. My 2023 LT 5.3L is so far not leaking anything.

  • 1 month later...
MidTNDenali Enthusiast

MidTNDenali

Posted
Posted
On 2/12/2024 at 7:58 PM, Sheryldk said:

I have a 2024 Chevy Silverado 1500 with 411 miles on it. Noticed yesterday and today two oil spots. Appt tomorrow with dealership. Anyone having same problem?

OP, what did you find out?

andrewb24 Enthusiast

andrewb24

Posted
Posted

I have a 2020 silverado with 45k miles and it was leaking a month ago, I looked quickly one day when i noticed a puddle on the driveway and didnt see any obvious leaks but a day later i went under and looked closer and it was due to the oil filter not being put on tight enough, i could turn it easily with my hand.

  • 2 months later...
RAS01 New Member

RAS01

Posted
Posted

My 2024 Silverado High Country with the 5.3 is leaking. Noticed it when I crawled under it to do the first oil change with about 4,500 miles on it. I bought the Truck at a dealer about an hour away because none of my local dealers could get the truck. However, I took it to my local dealer in Newark, DE Porter's Chevrolet 10 minutes from my house to have them look at it. They told me it was the Rear Main seal leaking. I dropped off the truck on a Monday late afternoon and picked it up Friday. I checked it the next morning and it was still leaking. Additionally, they had compromised the integrity of the Transmission oil pan by having used a large pry bar against it I guess trying to separate the Engine and Transmission. So, I took it right back on Monday. They again had the truck until Friday and told me they replaced another remain seal and housing, because GM won't let them just replace the seal. They also replaced the Transmission oil pan they damaged at no cost to me. I had a bust week and didn't get a chance to check it until the following week on a Saturday. Sure enough, it was still leaking. I called GM's Customer Care and have a Case number assigned and the GM Rep told me I could take it to a different dealer. So, I took it back to the dealer I bought it from in White Marsh, MD. They are looking at it and will get back to me tomorrow, but told me they may not be able to do the repair because GM already Paid Porters and won't pay twice for the same repair. I have a call into my GM Rep to see why he told me I could take it to a different dealer. What a mess. Might have to look at Dodge's for my next Truck. When I pay $70,000 for a Pickup truck I expect to be able to get it fixed when there is a Factory defect.        

Velocity12 Enthusiast

Velocity12

Posted
Posted

Brought mine in to the dealership for the first oil change a couple weeks ago. Took a road trip last week and then noticed a puddle of oil under the truck. Filter was loose so I just tightened it up. Keeping an eye on it to make sure it doesn’t come lose on its own. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      tl; dr I've now reached the 6th floor of hell. I'm chronicling my journey for my morning readers.   Pulling the top of the intake apart was moderately easy but it involved a lot of parts, connections, and minutae. I was preparing for the new fuel lines to arrive ("nut and bolt kit" it's called). The fuel line connections are notched and held in place by the manifold and a metal plate with a T27 screw.   It's on the back of the intake, under the firewall, with little clearance, and two hard metal fuel lines in the way. I was using Franken-tools (weird combinations of 1/4 inch ratchet with/without an extension, with a bit holder for my T27) to get in there. One of my sockets and bits fell off and has yet to emerge on the floor. I lost a second setup and that's when I almost started throwing tools. But that was the point at which I had gotten traction on the Torx head, and it promptly stripped. No more traction.   I started humming "1-877-kars-4-kids" because I was about at that point. You know what? I'm $1500 into this thing and I can make it disappear just as quickly. This isn't fun anymore. I had spent a lot of time already "tidying" around the engine bay: Fixing all the "someone's been here before!" BS. The truck has been exclusively dealer- and shop- serviced and I'm reminded of why I never let other people work on my cars unless absolutely necessary.   Speaking of dealer service. This truck has a 1" stack of records going back to 1995. I put them all in an excel spreadsheet, date/mileage/description.   The CPI spider has been replaced 4 times in 85k miles. The EGR? Another 4. Multiple, multiple O2 sensors. One Cat. 4? Sets of plugs and wires, and I swear half the stack is diagnosis paperwork for "misfire, runs rough, extended crank, dies at stoplights".   GM was producing some proper crap back then. And it was still well within the era of brittle/crappy plastic. (Windows 95 was released the same month this truck was sold new, we HAD the technology!!)   There (was) a plastic shroud around the evaporator core and HVAC fan in the engine bay. I noticed a chunk of it missing so I poked at it some more and it literally shattered. Touched it some more and pieces were crumbling off. Had a good laugh. Clearly whatever plastic garbage they were using had broken down over 30 years and was literally turning to dust. That was a good half hour of using a shop vac to remove the rest of it.   Back to it.   I was going to give up for the evening but then decided I'm already level 10 pissed off at the stripped screw: G* D* it, give me my tools back -- and my JOY. We'll do this the hard way: The whole intake is coming off.   Blazer won Round II. After finally finding and accessing the 12 intake bolts and using a pry bar to unseat it from the heads, it popped loose in an explosion of gunk and grime raining down into open ports. Awesome.   6 times I reminded myself: Be careful of the temperature sender on the front of the intake.   YEAH, I forgot again and snapped it clean off in the removal. Add another $20 to the ever-growing list of new parts this thing is consuming.   The shame is, long before removing the intake, I had changed the oil in prep for Tuesday's momentous fuel line replacement that was going to be the magic fix and I'd have a running Blazer to tool around in this next weekend. The intake removal, including raining gunk, also gushed dirty coolant all over the valley. Of course it did. Welp, there goes another $35.   I now need an intake gasket set, bolt set, coolant temp sensor, another 5 quarts of oil, some RTV. Don't worry, I've already got 3 new jugs of Dexcool and a thermostat waiting. I'll fill it with clean water first to get it running, dump it, and then add the Dex later on in case... well, let's not go there. I'm only tearing this down once, next time the truck is going on Marketplace for FREE.   Oh, and I'm going to need vacuum hose for all the stupid connections placed at the rear of the engine which have since disintegrated. Come on, GM....tell me you don't do that anymore?   Oh, and the ears on the distributor where the cap screws down are both cracked. I mean, why not put a new distributor in it too. You get a distributor, YOU get a distributor, Everyone gets a new distributor!   This truck isn't out of the woods yet...I'm already questioning how much more time I'm willing to sink in.
    • William Aldrich
      Bent valve in 2025 GMC Canyon Denali - Requires engine swap at 14K miles

      By William Aldrich · Posted

      NewDude, thank you for the suggestions!    I did follow up and the dealer indicates he has an open CX case and is working with DPAC (Dealer Parts Assistance Center).   Per the dealer, GM has had a quality spill and is not providing an update for when a replacement engine will be available.
    • Silver Yeti
      Poll: Does your truck have the rear window leak?

      By Silver Yeti · Posted

      That's interesting.   There was a factory wire-hole in the back, top of the rear cab, which had a wire for the third brakelight assembly running through it, as well as several holes (10 of them I believe) for all of the studs coming off of the 3rd brakelight assembly itself.   I sealed all of those holes with RTV/silicone as well.   I found it kind of odd, that none of those holes, were sealed with any kind of sealant by the factory - if there was any there, it wasn't very much.   That said, I've been out in heavy rain and have ran the truck through high-pressure car-washes a few times now and she has been 100% water-tight to this point.   I feel very confident in the repair, we'll see how it holds up.
    • Jay-22-2500
      2024 Silverado 2500 HD with the 6.6 Gas (L8T) Engine

      By Jay-22-2500 · Posted

      I bought a used 2022 2500hd with 6.6L in February. In March took a 2200 mile trip towing our 6500 lb trailer. Changed the oil day before leaving and when we were arriving at our 1st destination, low oil light came on (roughly 1000 miles) it was 2 qts low. Now it towed like a dream, no issue there, and we did go through the mountains of TN, but still, 2 qts! Luckily I did purchase an extended warranty. Brought it to the dealership in April, oil change and consumption test. Brought it back last week, 1300 miles, no towing, and no oil showing on the dipstick. GM is reccomending a new engine (cheaper than them rebuilding), we'll see if the warranty company comes through. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      T3's and Ibuprofen. I do have a cryotherapy unit (ice machine) and a lift chair that will allow me to raise my legs above my heart.  There are topicals that I can use once the wound is fully healed.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...