Jump to content

Recommended Posts

Posted
21 hours ago, fondupot said:

 

Yes, Ive been running the RLI 5W30. I'm at around 4200 miles on current oil change, and I've only added about 1/3 quart of oil this interval. And it still looks nice and amber when I check it on the dipstick. Pretty good stuff!

 

Now that is interesting. 

  • Thanks 1
Posted

Why not get a "1 size larger diameter tire";  not wider, just taller, and drive in M7 all the time to keep it out of 2 cylinder mode to eliminate the oil pumping action of dead cylinders??!!!

  • Haha 1
Posted
1 hour ago, Byrds8 said:

Wouldnt it still being amber be a bad thing after 4200 miles? 

 

Combustion byproducts and their oxidation products, like soot, are what colors up your oil. The tighter the ring seal the longer that takes. So, I see it as a good thing. The part that is interesting is, it uses oil and still remains pretty clean for a good long while. 

Posted
2 hours ago, Grumpy Bear said:

 

Combustion byproducts and their oxidation products, like soot, are what colors up your oil. The tighter the ring seal the longer that takes. So, I see it as a good thing. The part that is interesting is, it uses oil and still remains pretty clean for a good long while. 

Right. But after 4200 miles, whose oil is ever really still amber in color. I mean I have 2K since my last oil change. You can see some amber there but it aint perfectly clean. Wouldnt really expect it to be either though. But shoot 4200 is almost changing time.

Posted
3 hours ago, Byrds8 said:

Right. But after 4200 miles, whose oil is ever really still amber in color. I mean I have 2K since my last oil change. You can see some amber there but it aint perfectly clean. Wouldnt really expect it to be either though. But shoot 4200 is almost changing time.

 

Pepper goes 5K per OCI with 185K on her and still looks healthy. Runs on E-85 and has good rings. Looks between amber and light brown on chart below. 

 

Wife's Terrian, that one is between dark brown and black in a thousand miles. Rings are toast in that one. 

 

Rings, fuel, spark, oil, it all makes a difference. :dunno:

 

 

image.jpeg.da25e71aa1b324f658b395aef3f49fe3.jpeg

 

  • Like 2
  • Thanks 1
Posted

My avalanche and genesis are between the first and second dipstick at oil change intervals. It takes awhile to even see any change from a fresh oil change. The odyssey is just passing the second dipstick at its oil change. The two previous mentions use semi synthetic. The odyssey full synthetic. Most oil changes now are done at a valvoline quick lube. Yearly I’ll take the Genesis and the odyssey to the dealership for the free vehicle inspection. Yes they actually do it, I can watch. Those are at or past 150K miles. 

  • Like 2
Posted
On 10/9/2024 at 11:02 AM, customboss said:

My dealer service mgr says the PCV system is too “ strong “ for the design. I’ll take a qt in 5000 miles and run the RLI 5w30

thats $3.50 a qt and getting good wear and combustion readings. 
I purchased a 1978 J20 Jeep and it’s using no oil. 360 V8 I think.  

 

I can believe that but how does one design a breather system that must work for both a 1350 cc twin and a 2700 cc inline four and make that work? 

:dunno:

 

I've noticed lots of quirks in GDI AFM/DFM motors that make the head spin. Clean oil at the service interval and yet uses oil. Oil around the threads of the sparkplugs on the 'off' cylinders and yet a dry piston crown. Just weird stuff.  

  • Thanks 1
Posted
13 hours ago, Grumpy Bear said:

 

Pepper goes 5K per OCI with 185K on her and still looks healthy. Runs on E-85 and has good rings. Looks between amber and light brown on chart below. 

 

Wife's Terrian, that one is between dark brown and black in a thousand miles. Rings are toast in that one. 

 

Rings, fuel, spark, oil, it all makes a difference. :dunno:

 

 

image.jpeg.da25e71aa1b324f658b395aef3f49fe3.jpeg

 

When a lubricant turns color from bottle color it’s usually additive being heat activated. After that as Grumpy shared above its stress. I’ve never a coolant leak make the oil opaque. Milky mess yes. 

  • Like 1
Posted (edited)

RLI just went into my 1978 Jeep J20 truck 360 V8 that I think is a crate engine from Oreillys than never had an oil change since installation years ago. Unknown miles but its compression and ring seal makes me proud of AMC! 

Edited by customboss
spelling like a old man geezer
  • Like 1
Posted

Here’s what my oil looks like off the dipstick. This is around 4500 miles on the interval using RLI 5W30. The darker color is from dipstick. The lighter color is new oil for comparison. I did have to add about 1/2 quart or so after checking it. 
 

 

IMG_0700.jpeg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • I gotta say, I'm enjoying your narration. The troubles you've been having are amusing as you describe them. It's good to see that you're finally getting some satisfaction out the old beast though.
    • Declaring victory would upset the demons that possess this Blazer, so I won't. But I did make progress today--after it put up a fight. Always a fight.   I had the day off so I spent the morning cleaning up the shop and I thought I'd get ahead of things by filling the cooling system in prep for the final part I needed to arrive: the driver's side knock sensor. Glug, glug, glug....and then the unmistakable sound of liquid hitting the shop floor. It induces the same chagrin when the sonar and targeting laser temporarily malfunction during a late night bladder evacuation over the toilet with the bathroom light off. D'OH!!! That made a mess...   Oh, hey, that knock sensor I removed? It threads into a wet port. Who knew?! Learn something new every day. Put a pin in that chore, I'll fill it the rest of the way later.   The knock sensor arrived at about 1pm. I threaded it in, connected the wire, filled up the coolant, checked for leaks, and... drumroll.... fingers crossed for a perfect start, excellent timing, model fuel trims, and ...no squeaks... Here goes.....   No, it didn't start. At all. I cranked it a few times and it wasn't sounding good. Furthermore, I heard leaking again. Jesus H Tapdancing Christ, stop leaking all over the dang floor. This time I had accidentally overfilled the coolant reservoir and the churn of the water pump via cranking caused a bit to burp out. Ok, just, breathe... Put the flamethrower down. Dang thing wouldn't burn anyway, leaks too much...   Did you know the rotation of a round crank sensor in a round hole, matters? I do now. Took me about half hour to retrace steps and realize what I had done. Then it started right up.   No squeaks. The squeak was the old balancer.   Once it entered closed loop, fuel trims are dead on, hovering right around zero at idle. No more -30%. I'll credit the injector rebuild on that one.   Timing? I think there's an OBD 1.5 translation error with my Actron scanner. It's anywhere from -20 to -30 at idle, sometimes as high as -40 cruising. Sorry, the engine just isn't running that smoothly at -40 degrees ignition advance. It's just not. It's smooth all through the rev range and has decent power. I'm going to have to trust the seat of my pants on this one.   The new exhaust is very quiet. The old catalytic converter? Not melted, but definitely not healthy. Rains glitter when you turn it on its end...all the precious metal is flaking out. Once the new exhaust system burned in/smoked off a bit, the engine's exhaust smell is normal again. Not that I'd recommend going around huffing car exhaust, but, you know what I mean?   One problem to correct. The new exhaust has the opposite problem of the old spliced up exhaust. It wants to hit the floor where the old one wanted to rest on the cross member. Happy medium, please? Still noodling on that one, need to look at how I can adjust some hangers.   I don't know what's next. On one hand I want to run away from this thing as far and as fast as I can -- there have been a lot of NOT fun moments. On the other, now that it kinda drives nice, maybe drive it around for a little bit?   Shhh... it's not currently dripping oil all over the floor. I can see just a little wet at the bottom of the timing cover where it meets the oil pan seal. It's not dripping multiple drops with every ignition cycle, in fact, after some driving this evening it has yet to even form a drop that could drip off yet. But the weekend is young... I fully expect this could turn into Exxon Valdez by Sunday. Because this Blazer hates me. LOL.      
    • About that:   Once upon a time in a land far far away lived a car company that was shy about taking your money and wanted to be sure that they gave you more that you asked for so that you'd come back. No really, not a fairytale. 😱   But after the field got thinned out enough to limit the competition it seemed good enough to give you only what you asked for. Fair enough I say but in such a market you have to give something the others are not or they go to the one who does. Gimmicks or glitz. Oh, fins and chrome. Yea, shinny crow like cars. Yum.    Field narrows a bit more and 'brand loyalty' becomes a thing and the minute it does they start thinking to themselves, "Could we make more money if we gave them less than they expect and they will hang in there for brand and comfort with the known?" They gave it a try and da*n, it worked!!    Well, what if we teach them, groom them into believing that less is "Normal" and cut some more corners. Will that work? Oh heck yea!    🤔 I wonder, can we give then WAY less than they expect and make them mad enough to spit nails and STILL get them to pay up? Sure, if we get everyone else to do the same so that the choice is less or nothing at all. How would be do that? Platform sharing.  What a concept, right?  Steal like there is no tomorrow and it's legal too!    Truth is no one is going to give up driving, not for very long. The Gen Z crowd is fine with it and will be as long as someone not Gen Z will haul them around. At some point we all die.    Economic voting only works if you cast a NO vote now and again and enough of them to get dumb and dumber to wise up. Well, that's how I was taught anyway. And it should have worked. Would have worked. But the Bail out!!   Look, you have another choice if  you take that bag off your head. If the dumb it down to some predetermined expectation of how John Q Public will use it the, that is under design it to failure they you use it to a lower stress mode. D'ho!    A 1950 Royal Enfield Bullet 500 will go anywhere a Suzuki Hayabusa will and for just as long. But you will have to treat it for what it is and not for what you wish it was. 
    • Maybe I was just too unlucky, but I had nothing but bad luck with Bridgestones. Out of 3 sets, they all started losing a lot of air when they got down to about 1/2 tread life, and at that point also wet traction suffered more than it should have. Also, the only tire I ever had in my 60 years of driving that had a side wall blow out was a Bridgestone.   I'm currently running Goodyear Wrangler Workhorse AT and am very happy with them.   
    • maybe when the trip is over, check all the other joints in the front end, like all the ball joints, tie rods, pitman & idler arms, etc...
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...