Jump to content

Recommended Posts

Posted

2022 GMC Sierra AT4

My truck has developed a musty smell, wet dog, gym bag.. whatever you want to call it.  Its exceptionally bad when closed up and in the sun.  I think, but not convinced, its worse after rainfall.

I have not found any wet/dampness anywhere in the cab or surface of carpets.  Nothing is wet along the back wall under the window.  There is no sign of water (yet) to be found.

I have replaced my cabin filter and done the lysol trick.  I thought that his maybe had solved it, but a heavy rain last night peaked the smell again.

 

Since I can find no dampness in the truck, I'm really struggling to find the source.

Posted

Did you buy the truck new or used?  If used how certain are you the truck was not subject to flooding with the previous owner….
 

What part of the country are you in?

 

Is the a/c condensate hose draining when you are running the a/c..  make sure it is not plugged.

 

Household ammonia is a great deodorizer.   Leave a small bowl or container sitting on the floor board overnight (be careful not to spill any).

 

cabin air filters only clean the air when the vehicle a/c or heating system is running.

Posted

Bought new.  I'm in Toronto, Ontario, Canada.  

I am going to confirm the drain hose is not plugged.  I have typically seen water on driveway, but I'll make sure there its clear.

Posted
Just now, KARNUT said:

If you constantly run the AC in recirculating mode that can cause a musty smell.

I do not use that mode ever.  It may use it in AUTO, but I never manually engage it.  

  • Like 1
Posted

Have had the same issue in our 2021 Denali for years.  Had the rear window re-seal TSB performed once, and recently had the entire power rear sliding window replaced, and it still smells like this after rain.  Condensate line doesn't appear to be plugged, and not finding wet carpet anywhere either.  Clearly something is collecting water and allowing it to sit though.  

Posted
1 hour ago, windsurfnut said:

Ya, I don't want to start pulling panels and carpet up without some confidence I'm looking in the right places.  

Look carefully along the headliner above the rear window. Some of these trucks leaked above the high mount stoplight. Maybe check for wetness there after a heavy rain or a carwash.

Posted

We've had some heavy rain and I have no signs on the headliner.  I popped off the door trim and reached under the carpet at all 4 footwells and all was dry.  Reaching around the rear seats, all dry.

 

I'm searching for the AC drain with no luck.  WIth AC running I am getting water dripping out from under the vehicle in multiple areas.  Firewall liner is wet behind right front tire wheel well liner. Water is certainly exiting, but I cannot locate the drain too fish a line it and see if its partially clogged. Any guidance in locating the drain would be helpful

Posted (edited)

Found this pic, it may help. Supposed to be a 22 Sierra.

Screenshot 2025-09-25 at 09.35.44.png

Edited by Jay P
Posted

Only 2 things I could think of with this.

1) Do you have a sun roof? Maybe all of the water is not draining out every time.  

2) The drain holes in the bottom of the doors could be clogged and let water collect in the door. 

  • Like 1
  • Thanks 1
  • 5 months later...
Posted
On 10/3/2025 at 6:55 AM, 2016 Sierra Owner said:

Only 2 things I could think of with this.

1) Do you have a sun roof? Maybe all of the water is not draining out every time.  

2) The drain holes in the bottom of the doors could be clogged and let water collect in the door. 

 

 

I have a 2022 Silverado LTD with the 3.0L Duramax and mine has a moldy smell also after it rains. I've brought it to the dealership and they could not find a leak. The only area I have not confirmed is clear is the A/C drains. This is a frustrating mystery I would like to solve. I love the truck otherwise.

 

Did you have any luck getting rid of the smell? 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,759
    Total Members
    8,960
    Most Online
    DM22
    Newest Member
    DM22
    Joined
  • Who's Online   4 Members, 1 Anonymous, 1,856 Guests (See full list)

  • Latest Articles

  • Posts

    • I thought I would use your thread and add to it as I just did my first longer drive with my truck in the last couple of days. I drove from the Grande Prairie area of Alberta down to Edmonton and most of where I drove in the city was the ring road so fairly free flowing but a bit of stop and go as well in the city. Stayed the night and returned home and not too many stops along the way each way but every restart and certainly every cold start sets it back for fuel mileage. Why I say that is I see some people will cherry pick a fuel mileage leg after the vehicle had been warmed up driveline wise before hand and its a forgiving ( easy rolling drive leg for example ) and call that their fuel mileage which can give a false perception of reality. I was not heavily loaded at all but never the less the flip bak cover, rubber bed mat, various tools etc and extra jerry cans of fuel all way up to a few hundred pounds of dead weight so its not an empty truck. The cold inflation tire pressures are set more near the freezing point so once they are warmed up driving I was showing 45 front and over 40 rear and realize high inflation pressures would help a little in fuel mileage but certainly not the ride on our crap sections of highway. The weather was good so was not raining as that can really drag mileage down, in fact I had a bit of a tail wind on average driving home. Most people on here would never have driven on that freeway to visualize it but its got a fair bit of rolling type of landscape with numerous river valleys. For the most part I had it on cruise set to 62 although kicking it off if I caught it in time before it started down shifting and self braking going down the grades. Most of the more substantial grades its shifting into 7th I believe as 8th just doesn't have it. Total distance round trip was 643 miles and my overall average and I did refuel three times in all, figured out to 17.65 miles per US gallon. My best fuel mileage section refuel within all of this figured out to 18.46 and these are all hand calculated figures. I find if anything that the trucks computer can be over optimistic, sometimes its pretty close but other times its stretching it. On paper persay in theory the truck would have just about made it on fumes for that whole drive without refueling once.    Which made me think of the topic thread of the wonder if these trucks could do 20 mpg and that is a good question, certainly would have to be on an easy going flat highway, no head wind, the right temperature, not packing around a bunch of dead weight and puttering along even slower than I was I would suspect and going steady and not stopping to smell the flowers or take a piss !. It probably is possible but not without effort to attain that with the wind resistance and weight of these trucks. Of course on my drive most people are passing me if they have the power as per loaded highway tractors, never mind a lot of speedy vehicles but the speed limit is 68 and most are at or well over that. 
    • Monday looks like a good day for the dealer to test an ac issue. Hopefully it all turns out good.
    • Paid $2.72 for E85 today.
    • Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...