Jump to content

Recommended Posts

Posted

Does our 4-wheel drive system need to be exercised? If it is not used a lot?

  • Like 1
Posted

Absolutely!  These forums are legion with posts of people complaining that their truck wouldn't go into 4WD when they needed it to.  Most of them hadn't used it ever or in years.

 

I try to run mine through the paces every month or so and drive it a few miles on a dirt trail near the house a couple times a year if not already off-roading.

  • Like 1
  • Thanks 1
Posted

It is always a good idea to exercise it at least every few months to make sure the actuators don’t get stuck. It is also a good idea to actually drive it for at least a few hundred feet when you do that so seals experience motion and oil movement.  Off pavement or snow/ice is best for this, but driving wet pavement in a straight line for a  short distance will work if you don’t have other options. I have  forgotten and gone as long as six months between exercising it on my 2021 and it has always shifted promptly.  I usually just use my straight 300 foot gravel driveway.  

  • Like 2
Posted

It may or may not help with keeping things working, but even if it doesn't help, testing that it does work when you don't need it, makes it more likely it will work when you do need it, and/or you can fix the problem so it works when needed.

  • Like 1
Posted

Definitely its a habit to get into, every so often go through the motions of both high range and low range and allow it to rotate over for some distance to coat all the surfaces with oil that otherwise may not receive any otherwise and like was said to coat and work the seals etc. I too am doing it on a non busy gravel road during the summer or come winter again the snow covered gravel road simply because its not busy and can mess around putting it into four low. Of course I am using four wheel high range quite often for portions of each drive all winter which would be different then one who lives in an area where unless going off roading the four wheel drive almost never gets used. 

Posted

I do on occasion. Not super often but maybe once every 3-4mo I’ll just put it in high on a straight section of road for a few miles. 

Posted

I live in Vermont, 4WD gets used quite frequently during the year. 😀

  • Like 1
  • Haha 1
Posted
1 hour ago, rjgvt said:

I live in Vermont, 4WD gets used quite frequently during the year. 😀

 

I doubt two wheel drive pickups are a hot seller off the new vehicle lot in your area !, I highly doubt any of the dealers around here have brought in one two wheel drive pickup for many years as that four wheel drive system isn't along for the ride here or I can well imagine in Vermont during the winter. Of course some of our more poorly maintained gravel roads are so bad that during the summer if it rains a person could get stuck right in the middle of a gravel road in two wheel drive LOL. 

Posted (edited)

I have owned many GM 4wd vehicles dating back to the 1980's and driven all the big 3 brands at work (GPS Survey team).  Granted I live in upper Michigan where its winter (300+ inches of snowfall this past winter) from Nov-April (+-) but other than having it in AUTO 4wd then, I never excise it when I don't need it.  Never an 4wd issue ever.  Btw, according to a fiend who is GM tech, 99% of 4wd issues he encounters are attributed to oversize tires.

 

Now if you are one who has a 4wd just for a status symbol (many do) and really never use it then it might be a good idea to do that occasionally just to make sure you know how to use it. LOL. 

snow total 25-26.jpg

Edited by Z45
  • Like 1
Posted
14 hours ago, Pryme said:

I do on occasion. Not super often but maybe once every 3-4mo I’ll just put it in high on a straight section of road for a few miles. 

Same no dirt roads, so I put it in 4hi on a straight stretch of road, set the cruise to 45, and go.

  • 3 weeks later...
Posted
On 6/10/2026 at 9:54 PM, rjgvt said:

I live in Vermont, 4WD gets used quite frequently during the year. 😀

Cool to see another Vermonter!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Why don't I have a good scanner? I've always wanted one when I've needed one.   My latest reading says I don't need to do a relearn on the ckp sensor on a 1995 with OBD 1.5. The relearn is prescribed for the later-model 1995's which shipped with actual OBD II when GM completed the transition in prep for the 1996 MY. I need to confirm that. Did you know forums are disappearing? Knuckleheads on Facebook... it's not the same. It's just not.   So, scanners. Again, shooting myself in the foot for having eBayed my Snap On MT2500 "brick" with all the adapters. Not that I couldn't buy another but those are getting quite old, and mine wasn't new enough to work on 2000's vehicles.   Damn it (as I'm scanning my email between paragraphs here). Did you know there's a 2000 Jimmy 2-door on BaT that's ending this morning? It's local. I want it. 14k miles. Absolutely beautiful.   Back to scanners. MT2500's are old. Solus, now that could be a contender. There's a ~2008 Verus with a system error that's basically new in box for cheap. Hmm...I'm not sure about a scanner that runs an archaic version of windows (95 or CE, I can't tell).   I want the ability to reset and rotate TPMS, test individual modules, bleed ABS, electronic parking brake controls for servicing brakes, relearn procedures and other bidirectional controls.   Snap On does an MT2600. It's a new model as of last year, marketed as their "entry" scanner. Entry? Only where $1900 gets you through the doorway plus, I'm guessing, $1000/year if you wish to keep it current. So goes scan tools actually designed for production environments. Want decent products with excellent support, you pay for it.   Everyone is raving about Autels and TopDons and Foxconns and all these newer brands that are selling the $500 "prosumer" scanners for backyard hacks like me. They're tempting...honestly. Updates are cheaper, base prices are remarkably cheaper... And you get to deal with bugs and translation whoopsies and, well, just don't use it on anything expensive, OK? Having a dealer replace an ECU because it needs to be re-imaged after an adventure in scanning is no joke. But I think most people are getting by OK with these units.   eBay on a scratch-and-sniff pro-model oldie, a shiny new TopDon, or???   God dang it, I can't stop looking at this Jimmy. I'm ready! I'll Bring The TRailer! It's beautiful.
    • I removed the OE running boards.  It looked so much better.  I wish I took them off a long time ago.     I had to put something back on for my wife.  I wanted Westin Sure Grip Running Boards but they are very pricey, like $600 plus.  I was going to go with the Ionic 41's like I had on the 2019 Silverado but went with Westin Outlaw Drop Steps instead, about $200 cheaper.  They are sturdy and functional but not super crazy about the look, but it works.  
    • It's all a crock of 💩
    • I had a Gen5DIY DRL relocate harness from a 2022 1500 that I saved. I had Gen5DIY modify the harness for my 2024 Silverado 2500. Plug n Play, worked perfectly.    Here's a video I made for the 2022 1500 truck. The install is more or less the same on a 2500.    The harness relocates the DRL tot he top amber turn signal on my 2500.     
    • Can ask that about a lot of places.   Holiday sells 91 for $1 over 87 octane. BP 93 is 80 cents. Amoco 93 is 80 cents Kwik Trips is $1.20 for 92 or whatever they have and $1 for the 91.   I know that this is not exactly same as what you are saying with the premium to premium debate of those two stations but why is there such a difference. Top Tier this and that, it's all BS. All the fuel comes from the same damn refinery, so give me a break.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...