Jump to content

NAV and 6 disk changer in a Silverado

linda

By linda
in Audio, Electronics & Software

Recommended Posts

  • Replies 923
  • Created
  • Last Reply
280hpacura Enthusiast

280hpacura

Posted
Posted

I have a 2005 Silverado CC, with the bose sound system. If I take the bose amp out and replace it with the lux amp, can I buy a gm navigation, radio from ebay and just plug it in??

 

I have the rear seat controls and the steering wheel controls, I want everything to work.

 

Is there any splicing required to change the radio, or amp??

duramaxHD Enthusiast

duramaxHD

Posted
Posted

not exactly...you need to do some rewiring at the amp connectors to get the lux amp to work. read the beginning of this thread for instructions on how to rewire the amp connectors. if you get stuck in the process, we can all help out!

 

--Ben

 

PS-- remember you also need to buy a GPS antenna

280hpacura Enthusiast

280hpacura

Posted
Posted
not exactly...you need to do some rewiring at the amp connectors to get the lux amp to work. read the beginning of this thread for instructions on how to rewire the amp connectors. if you get stuck in the process, we can all help out!

 

--Ben

 

PS-- remember you also need to buy a GPS antenna

 

<{POST_SNAPBACK}>

 

 

 

I also have on-star. Is the GPS antena different then the onstar antenna?

BBSilverado Enthusiast

BBSilverado

Posted
Posted
not exactly...you need to do some rewiring at the amp connectors to get the lux amp to work. read the beginning of this thread for instructions on how to rewire the amp connectors. if you get stuck in the process, we can all help out!

 

--Ben

 

PS-- remember you also need to buy a GPS antenna

 

<{POST_SNAPBACK}>

 

 

 

I also have on-star. Is the GPS antena different then the onstar antenna?

 

<{POST_SNAPBACK}>

 

 

 

 

The GPS antenna is different and a separate antenna. The GPS antenna mounts under the dash pad near the center defroster vent.

280hpacura Enthusiast

280hpacura

Posted
Posted

I have been searching for gm navigation systems on e-bay and have found two that in the desription say, "Will work with any gm bose system, does not need lux amp."

 

Can this be accurate??

BBSilverado Enthusiast

BBSilverado

Posted
Posted
I have been searching for gm navigation systems on e-bay and have found two that in the desription say, "Will work with any gm bose system, does not need lux amp."

 

Can this be accurate??

 

<{POST_SNAPBACK}>

 

 

 

 

I don't see how that can be, the lux models use a digital audio low level signal and the non lux use a analog low level signal. The non-Bose units use a high level analog (speaker level) output.

All the unit have the same pinout configuration but the difference is in the signal they put out.

dbcomm Enthusiast

dbcomm

Posted
Posted
I have been searching for gm navigation systems on e-bay and have found two that in the desription say, "Will work with any gm bose system, does not need lux amp."

 

Can this be accurate??

 

<{POST_SNAPBACK}>

 

 

 

I got one of those - sent it back. It worked...kind of. Had a pretty bad hum and stayed on when the car was off. The guy said he worked for GM and reprogrammed the software in the radio to work with either AMP. I ended up doing it the right way. Got the LUX AMP and the correct HU.

280hpacura Enthusiast

280hpacura

Posted
Posted

Has anyone, or does anyone plan to write a tech articel on addung a navigation system to a silverado? This wold be helpful. I would like to convert my truck, but I am a little learing about the wiring involved in changing the amp.

 

I also would need direction in removing the dash pad, radio bezel, and getting to the amp. I am able to do almost anything, but I do need explicit instructions.

Amos33 Enthusiast

Amos33

Posted
Posted

me too lol. i finally got all my parts together. Gonna try to do it very soon. There is an avalanche fan club, there is good directions there.

Amos33 Enthusiast

Amos33

Posted
Posted

How on earth do you get the two screws on the front/engine side of the amp out. They are under that metal plate, i can get the rear ones easy.

camaudio Enthusiast

camaudio

Posted
Posted
How on earth do you get the two screws on the front/engine side of the amp out. They are under that metal plate, i can get the rear ones easy.

 

<{POST_SNAPBACK}>

 

 

 

Im wondering the same thing.

 

I got all my parts in

TNR Part # 15230099

LUX Amp# 15191601

I only did the wiring mods at the amp cuase thats all i could find.

I got the Theftlock msg right away and did the trick to bypass it.

Started playing with it and didnt get any sound and my nav disc wouldnt recognize.

Everything else works.

 

Can someone email me the other mods needed?

[email protected]

 

I stopped by my local dealership to get theftlock removed and they wanted to charge me an 1-1.5 hours so i left and i will try another one today

 

Thanks for any help, this thread has been very helpful already.

Cant wait to get this all working!

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined

  • Who's Online   6 Members, 1 Anonymous, 623 Guests (See full list)

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • Chuck FB
      Tire pressure for 37s

      By Chuck FB · Posted

      First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Snowcamo
      Possible lifter tick after DOD delete

      By Snowcamo · Posted

      Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 
    • rdonarski
      Towing In Loose Gravel

      By rdonarski · Posted

      This landing is worse than most. Patchy blacktop with washouts, soft gravel/sand at bottom that washes out with every heavy rain. I tell everyone to put it in 4WD. A lot of them think they can pull out their trailer in 2WD. They end up digging a hole and then putting it in 4WD.  The lake is a pristine lake and has a lot of money on it. There are several wake boats and lot of large tritoons. The people with the money don't want it improved because they don't want more traffic.    Boat Landing 1.jfif Boat Landing 2.jfif Boat Landing 3.jfif
    • PBNB
      Tire pressure for 37s

      By PBNB · Posted

      How wide are your rims?   Toyo specs 8.5-10.0-11.0 inches. My thought would be rim might be pulling the tire inwards creating a center that is more pronounced.    I also noticed that the spec sheet says max 65psi. So you could be right lowering the pressure to ~40 psi. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...