Jump to content

Recommended Posts

Posted

Looking to buy a set of amp steps for my 2017 1500.  It currently only has a 2" level but I plan on lifting the truck next year so wanted to just buy them now.  Is anyone running these on a 2" level?  I'm just curious as to how low they drop down when they are in the down position.  

  • 2 weeks later...
Posted
On 10/8/2017 at 6:13 PM, SierraZ714x4 said:

Just won a set of AMP steps with plug and play off ebay for $560...... lucky day

Have you received these yet?  I have found something similar, just worried that it could be too good to be true.

Posted

Just installed a set of Havoc HS2 nerfs on my 2015 Sierra. Highly recommend them to anyone looking for a set of steps

IMG_1199.JPG

  • Like 1
Posted
On October 21, 2017 at 7:47 PM, AcadianaTiger said:

Have you received these yet?  I have found something similar, just worried that it could be too good to be true.

yes i have received and installed them. 100% legit from a verified seller on ebay with 100% feedback so i trusted it. the lowest price i have seen by it now is around 1200 so i got extremely lucky with the no reserve auction.

Posted
On 10/6/2017 at 6:47 PM, spoolindawg said:

Heres the Westin HDX installed on my 17 LTZ.

 

Fairly easy install, would have been a lot easier if the damn brackets were labeled, didn't even use the instructions as they were not very understandable. Also had hell getting one of the bolts started, ended up being some slag inside of the bolt hole on the running board.

 

Not a fan of the way any boards look but couldn't justify the Amp researches, i also have a a very expensive gun and watch addiction I need to feed lol.

 

pxIBdGY.jpg

 

Those steps look great. They hug the rockers nicely.

Posted (edited)

I installed amp boards on my single cab this last weekend and love them , had to make them fit since they don't make a set for single cab

IMG_0984.jpg

IMG_0985.jpg

Edited by wing98
  • Like 2
Posted
I installed amp boards on my single cab this last weekend and love them , had to make them fit since they don't make a set for single cab
IMG_0984.thumb.jpg.c54ab3f6b87e0ffa2513a9ab0d84bec3.jpg
IMG_0985.thumb.jpg.497c358e1a7e6d16a982729c913e8d86.jpg

Wow.... how exactly did you manage this?


Sent from my iPhone using Tapatalk
Posted (edited)

I had to move the rear mounts forward to clear the cab mount , works great had to move it 6 inches and drill new holes it puts the rear mount right where i step so works perfect 

i cut the boards 44 inches 

Edited by wing98
  • Like 1
Posted

I have a Short GF who is wanting me to get a set...not a fan of any either so...i guess i will pick one that looks good.  Cheaper to get rid of the GF thou...

  • Like 1
Posted
16 minutes ago, Scuba78 said:

I have a Short GF who is wanting me to get a set...not a fan of any either so...i guess i will pick one that looks good.  Cheaper to get rid of the GF thou...

Nice guy.

:happysad:

Posted
2 minutes ago, Scuba78 said:

Facts are facts sir.

True.

Fact;

Running boards that are rocker mount aren't the best.

Frame mount are IMO.

:happysad:

Posted

I sort of disagree.  Both have pros and cons.  The problem with frame mount is that they require longer brackets and thus cause more stress on the frame.  Rocker mount has shorter brackets and are fine as long as the brackets are well made.  The most common type of mount is rocker panel and I've never really heard of anyone tearing off their step bars from the mount.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,760
    Total Members
    8,960
    Most Online
    MASONV88888888
    Newest Member
    MASONV88888888
    Joined
  • Who's Online   3 Members, 0 Anonymous, 1,609 Guests (See full list)


  • Latest Articles

  • Posts

    • I’m definitely interested to hear the end result here. 
    • My 2025 Silverado 1500 had to receive a brand-new engine (long block) under warranty last month at only around 16,500 miles. Before the replacement, the truck repeatedly displayed "Engine Oil Level Low" warnings, even though the Oil Life Monitor still showed around 50% remaining after about 6,000 miles since my last oil change. After seeing the warning several times, I checked the dipstick with the engine cold, and the oil level was completely normal. The next day, the message escalated to "Add Engine Oil." At first, I assumed it was just a faulty oil level sensor, so I brought the truck to the dealership. After inspecting the engine, they found internal cylinder wall scoring and ultimately replaced the entire long block under warranty. Before this happened, I was planning to install a 4-inch lift and suspension upgrade on my truck. After needing a new engine at just 16,500 miles, I honestly don't see the point anymore. I also contacted GM to ask whether my vehicle qualified for a buyback, but I was informed that it does not at this time. Anyway, this experience has left me with serious concerns about the long-term reliability of this engine. I sincerely hope NHTSA expands the current investigation or recall to include 2025 model and performs a thorough inspection of affected vehicles. My biggest concern is that these engines may fail shortly after the powertrain warranty expires. If GM truly stands behind this engine, then at the very least, please consider extending the powertrain warranty to 10 years for affected owners. That would go a long way toward restoring customer confidence.
    • Without exception but then I'm the odd duck, right? I know what goes into that test, how it is calculated and thus how to beat it. But EPA values are often not beaten by the general public and the government has in past years adjusted the means and methods to come to those values to more closely approximate "Joe Average".    The only real trick to beating that EPA average is don't drive like "Joe Average".    It's the same method you used to profit from "Economic Migration" and in doing so beat the 'stats'. But you, like me, are not "Joe Average".     The thing you don't seem to grasp is this "Purchasing Power Index" isn't forward looking. It doesn't predict what it going to be but looks backward and states what it was. They are not telling us what the THINK, they are telling us what they MEASURED. Example:    Wife says "I'm going to lose 40 pounds by Christmas". May she does, maybe she doesn't but the doctors office who weighed her when she made that statement and again at Christmas only REPORTS what the RESULT was. You and I can banter about what was possible and what aunt Tilly did till the cows come home but the result is the result. Arguing otherwise is.....irrational. That's all I'm saying. This isn't about:      What you are calling a 'Statistic' is a RESULT not a CALCUATION and as a result the RULE. Like gravity as a rule, it can not be broken. 
    • Just wanted to say thank you for posting this. Years later, your thread is still helping Silverado owners.   I bought my 2025 Silverado 1500 in January 2025, and I've had what feels like the exact same rattle since day one. After reading your findings, I believe my truck has the same issue with the cable carrier contacting the rear sliding window. To be honest, I had pretty much given up on pursuing the issue. It wasn't until I recently drove another brand's pickup that I realized just how quiet their cabin was—and how noisy mine has been all along. On my truck, the rattle happens on almost any paved road, gets even worse on rougher pavement, and I can even hear it during braking and acceleration.   I actually referenced your thread when submitting my case to GM, hoping they'll recognize this as a recurring issue instead of treating it as an isolated incident. The reason I reached out to GM first is because my dealership told me they would need to keep the truck for at least two days just to diagnose the problem. I was concerned that even after two days, they still might not be able to identify the source of the rattle before giving the truck back to me. I had also asked a few dealerships about this issue during previous service visits, but none of them seemed to know what was causing it or had a solution. That's why I decided to contact GM directly first, hoping they might already have an official repair procedure or guidance for this issue.   I also hope GM eventually comes up with an official fix for this problem. I have a feeling there are many Silverado owners experiencing the same rattle, but most either choose to live with it or simply don't know what the cause is.   Really appreciate you taking the time to document your diagnosis. Your post is still making a difference years later.
    • I have 2 choices. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...