Jump to content

Recommended Posts

Posted

Hey all. Just tried to installing my 5100s tonight. They didn't fit!

 

I dont know if anyway else ran into this problem, but the diameter of the piston is larger than the inside diameter of the spring hat. I grabbed a caliber and measured out of confusion. Sure enough, the diameter of the 5100s were about 1/32" larger than the stock piston.

 

Not sure if this is an isolated isue with me or not. Some insight would be much obliged.

 

And i broke a spring compressir :( what a night lol

Wow - what?

I too just installed my Bilstein 5100's and everything worked perfectly.

Do you have a photo showing the interference fit with the spring hat?

  • Like 1
Posted

So, I'm trying to determine my best option. I have a '16 CC Z71, front measurement 36.3 and rear 39.6. I'm looking to replace the stock tires with something a little more aggressive and am looking to go with a 275/60/20 with the stock wheels. In your opinions, is it possible to go with the front 5100's on the third setting, potentially raising the front end to around 37.5 and is it possible/advisable to pull the rear blocks and go with the rear 5100's on stock setting, leaving the rear to be sitting roughly at 38.4, leaving a little bit of rake? Also, if this is something that is advisable, will 275/60 wheels fit without rubbing? Thanks all.

 

Sounds like a solid plan, you may want to just put the 5100s on the top setting tho. 275/60R20 on stock wheels will be fine with any type of leveling kit, should have no rubbing issues. You might be able to get away with a 275/65 with only rubbing on full lock.

  • Like 1
Posted

Hey all. Just tried to installing my 5100s tonight. They didn't fit!

 

I dont know if anyway else ran into this problem, but the diameter of the piston is larger than the inside diameter of the spring hat. I grabbed a caliber and measured out of confusion. Sure enough, the diameter of the 5100s were about 1/32" larger than the stock piston.

 

Not sure if this is an isolated isue with me or not. Some insight would be much obliged.

 

And i broke a spring compressir :( what a night lol

 

Oh no, sorry to here of the install troubles. So, lets first check the part number to make sure you got the right shocks. Are they factory upper mounts, or aftermarket like Monroe?

I have a 2016 Sierra CC STD Bed, NHT with 1" level spacer in the front and a 1" lift spacer in the rear. I plan on keeping the spacer in both - what combination should I go with? 4600's in front and 5100's in back?

 

5100s all the way around. 1st or 2nd setting only on the front.

  • Like 1
Posted

So on my old '7 GMT-900 before I added my 6" BDS lift. I added a 2" RC leveling kit and added 305/50/20s. I love how the truck drove and handled afterwards.

 

Before I got my '14 Silverado, I had a '08 Toyota Tundra Crew Max that I had put 5100s on top setting to achieve my level look. Just wondering what I should do?

 

 

 

Go with the top setting on your new set of 5100s :)

 

2014+ Complete 5100 Set - http://shop.mrtmotorsports.net/bilstein-shock-sets/bilstein-5100-complete-set/2423830433238319/i-2304103.aspx

Posted

I have a 7-9 adjustable McGaughy lift on a 2014. I do not like the McGaughy shocks that came with the lift. What part number Bilstein shocks would work with my setup? It's currently set at 7" lift. Any higher and I cannot get into my garage. Thanks!

 

 

Sent from my iPhone using Tapatalk

Posted

You truck does look good regardless! Are you planning to add some larger tires? A set of beefy all terrains on there and the stance would be great.

Yeah looking to throw 275/70r18 KO2s on it and probably a 1 inch rear block.

 

Sent from my SM-G900P using Tapatalk

  • Like 1
Posted

I have a 7-9 adjustable McGaughy lift on a 2014. I do not like the McGaughy shocks that came with the lift. What part number Bilstein shocks would work with my setup? It's currently set at 7" lift. Any higher and I cannot get into my garage. Thanks!

 

 

Sent from my iPhone using Tapatalk

 

There are no front Bilsteins that will work with that kit as it uses its own proprietary lift shock. Your only option up front will be custom built Fox, ICON, RadFlo or King shocks. We do have some that will fit the rear.

Posted

 

There are no front Bilsteins that will work with that kit as it uses its own proprietary lift shock. Your only option up front will be custom built Fox, ICON, RadFlo or King shocks. We do have some that will fit the rear.

Dang, that's what I was afraid of. Thanks for the reply.

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

Not sure if anyone would know the answer to this but here it goes. If I run a .5 inch spacer on top of the 5100 on the highest setting (totalling 2.3 inches of lift), can I expect it to handle similarly to a 5100 on the bottom setting with a 2.5 inch leveling kit? I don't really see what the difference would be. All the 5100 does is increase the length of the coilover by raising the spring seat. Spacer kits effectively do the same thing, right? They just increase the length of the coilover. I'm more curious than anything else.

 

Sent from my SM-G900P using Tapatalk

Posted

They are different. The Bilstein gets height by adding pre-load to the spring, where as the spacer gets height by increasing the overall shock length. A spacer limits travel, where as the Bilstein allows the max travel to be used.

 

A spacer is pushing down on the shock, where as the Bilstein does the opposite, causing the spring to push outward expanding the shock.

Posted

What are the prices for just the front adjustable and will they fit on a 2017 GMC Sierra 2wd?

Posted

What are the prices for just the front adjustable and will they fit on a 2017 GMC Sierra 2wd?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,894
    Total Members
    8,960
    Most Online
    TopBo
    Newest Member
    TopBo
    Joined
  • Who's Online   0 Members, 0 Anonymous, 1,234 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • not all plugs will be used.  gm uses more generic harnesses that support most/all options, and if your truck doesn't have a specfiic option, the plug won't be used (commonly will have a dummy insert in the plug , or it'll be taped up, but some may just be left as is).  But it's sldo possible some p.o. has installed the wrong/cheaper parts that aren't correct for your vehicle...
    • First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  
    • I always drive in Sport mode. With more driving, I am finding the initial response when accelerating is much quicker now🖕 Lou
    • Is it an optical illusion in the pic or is the truck really squatting that much horribly?
    • My initial introduction was here.  It's hard to believe that I last posted in February 2013, having just deployed to Kyrgyzstan.  Since then, I've retired from the military and the 2006 Sierra SLT Z71 that first brought me to these pages was lost.  I went forward to Afghanistan in March 2013 and did a lot of sitting behind a computer on brigade staff.  Within 18 months of getting back to the States, I was selected for Drill Sergeant duty, after which I moved back to Virginia (my home state and where I served from 2004-2008).  That '06 Sierra did a lot of driving between Louisiana, Georgia, and Virginia, and ended up with nearly 320k miles by 2022.  By then, the registration had been expired for a couple of years, but the pandemic had all but eliminated tickets for such transgressions.  Admittedly too, I usually drove my wife's SUV or son's car the 2-3 times a week I had to report to work.  Teleworking sure was fun while it lasted.   I started my retirement leave four years ago and stored the Sierra at my sister's house.  A big mess was made when her fiancé passed while she was taking care of business out-of-state in late-2024, and his son pretty much mismanaged everything to do with the estate.  Even so, I was assured that my truck was safe... until it wasn't.  I found out that my truck had been scrapped about four months after the son took over everything.  There's nothing I could do; I'm 1000 miles away and it was technically abandoned property since he'd even trespassed my sister from her own house (she had no claim to it as she wasn't married, and the fiancé was the sole owner).     Anyway, today I got my second Sierra.  This is a 2010 SLE 2WB CCSB with a little over 200k miles on it.  It's got the 5.3L I'm familiar with and should handle what I need it for.  Hauling stuff that won't fit in the Transit Connect (yep, I sold out, but that's the wife's vehicle) and towing a few times a year tops.  The price seemed decent, considering how much people sell their trucks for in the Deep South: $4500.  I've seen similar trucks listed for more than double that.  I got it from a coworker who left his tag on until we transfer the title next week (Louisiana requires a notary for transfers), so I've been driving it all day.  The rear speakers don't work, which is one of the things that brought me back to these forums earlier.  I can't say how active I'll be as a poster, but I'll be scouring the archives while I find out every little thing I can about the 2010s and particular nuances/problems with my truck.   It's definitely not a GMC, but I got another Willys Jeep a few months back as well, so I'm almost at the same place I was when I first joined gm-trucks.com.  My old 1960 DJ3A was sold back around 2010 or 2011; my current Jeep is a 1946 CJ2A.  So, I've got a slightly newer GMC and a much older Jeep.  I kind of wish I still had that F-250 I had way back when too.  The Dakota is long gone and was technically my brother's truck, though I had it registered and insured.  The F-250 had to go when my grandmother's house was foreclosed on due to mismanagement around 2012 or so.     Hopefully anyone that made it this far isn't too annoyed.  I tend to be long-winded, but I'll be doing more reading than posting in the coming months.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...