Jump to content

New Lifters, should I do an Oil Change?

volrus

Recommended Posts

volrus Enthusiast

volrus

Posted
Posted

Last week the left bank lifters were replaced on my 2015 Silverado. My question is this, should I do an oil change prior to the usual oil life expiration as a result of them doing the work and having the engine opened up?

thewhitestallion Senior Enthusiast

thewhitestallion

Posted
Posted

I would check the oil to see if it appears to be fresh oil. However, if they did not replace the oil then I would replace immediately. If they did replace the oil I would prob put 500 miles on it and then replace the oil just to get any metal out of the oil that wore while the lifters were breaking in.

Thomcat Senior Enthusiast

Thomcat

Posted
Posted

I would check the oil to see if it appears to be fresh oil. However, if they did not replace the oil then I would replace immediately. If they did replace the oil I would prob put 500 miles on it and then replace the oil just to get any metal out of the oil that wore while the lifters were breaking in.

X2

fondupot Senior Enthusiast

fondupot

Posted
Posted

I would have expected the dealership to change the oil when they did this service, but I wouldn't be surprised if they didn't.

b1gted Enthusiast

b1gted

Posted
Posted

I would have expected the dealership to change the oil when they did this service, but I wouldn't be surprised if they didn't.

X2

Vic15 Enthusiast

Vic15

Posted
Posted

I would have expected the dealership to change the oil when they did this service, but I wouldn't be surprised if they didn't.

It's not what you expect it's what you inspect. We are talking about youngsters working at a dealership.

volrus Enthusiast

volrus

Posted
  • Author
Posted

How many miles? Why were they replaced? Good info for other owners regarding afm, lifters, etc.

 

Id change it too.

22k miles. They were replaced because one of them was "stuck". This occurred the day after I towed my 7500 pound camper about 500 miles. Engine was cold, I pulled out on the highway in 4 cylinder mode, went WOT to merge into traffic, the check engine light went on flash, stability control light came on, and truck was shaking and running very rough. My AC went out when I was towing the camper. Cause was a hose that split, thus losing all the freon.

volrus Enthusiast

volrus

Posted
  • Author
Posted

So I assume it's safe to say they didn't replace the oil if it isn't itemized on the ticket and they didn't reset the oil life indicator?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      // Thank you, also for your  response. More information is always good. This 2013 GMC is most likely my 'forever truck"-I'm 77 and retired...and truck only has 42K on it-very clean-so I try to keep it that way.  Tks again for your  response- glenn
    • smooth68
      Alternate wiring for Kicker sub with Bose system. (DO THIS)

      By smooth68 · Posted

      I started my install this weekend. Everything was pretty straight forward but I ran into one issue with running power through the firewall. The nipple grommet on my High Country already has a small harness running through it - has anyone else ran into this issue? And on the engine bay side, does the wire basically just penetrate the factory wiring boot? I did this on my '22 Trail Boss and it seems much easier but thats been a few years. My other thought would be possibly drilling a new hole adding a rubber grommet just to the lower left of the factory hole. Thoughts?   Has anyone used a T-harness off the Bose amp and obtained power from there? It seems a little odd that such a small amp needs 3 power leads
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      ///// Ok--Thanks for that info--I could not find yesterday when I looked for the specs on that NAPA filter what I wanted. Their website is not very user friendly. I buy all teh filters for  our three vehicles once or twice a year. Have always run NAPA Gold on everything I own....I buy it thru my Son's account for his business-which he has a Heavy Equipment repair shop-one reason he uses NAPA so much-they have such a full line of coverage for just about anything/anywhere- He gets s  good discount because of volume bought. Anyway-Thank you -Sir for your response.   glenn
    • PhilB
      No 12v outlets in 2026 gmc Sierra

      By PhilB · Posted

      It is possible to add your own 12v outlet to your truck.  Check out this video:   I verified via GM Upfitters that pin 31 is the same on the 1500 trucks.  The wire is GM part number 84779405.   You can get the GM 12v outlet from Amazon  https://www.amazon.com/Genuine-Accessory-Receptacle-25774623-13549530/dp/B0F1H9YRGF EWAY 12 Volt Power Adapter for GM   https://www.amazon.com/EWAY-Chevrolet-Silverado-Cigarette-Ignition/dp/B0915RRW6Q/ref=sr_1_1?   I just haven't figured out a good place to put the 12v outlet in my truck.   Some people are getting USB-C to 12V adapters  https://www.amazon.com/WYMECT-Cigarette-Lighter-Socket-Adapter/dp/B0F87WNQKB/ref=sr_1_1_sspa? Not sure if they provide the correct amperage that a device like a tire inflator would need.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...