Jump to content

Recommended Posts

Posted (edited)
5 hours ago, bluemonstercali said:

anyone have any suggestions for getting a s&b cai system in California????? I really one and live near their factory but due to California's "wonderful laws" i ca not get one. open to ideas fellas.

Find a friend or relative that lives in another state order it and send it to you.

Edited by Jay P
  • Thanks 1
  • 8 months later...
Posted
On 10/15/2019 at 10:53 AM, fatwhiteboy said:

Does anyone know with the GM Part #  84789804 Cold Air Intake if the filter media can be washed and reused or not.  The instructions say to replace the filter with a new one part number 84428120 every 20K miles.  Every other dry media CAI is washable.  These filters are hard to find and expensive..

 

Posted

Need some advice.  Have A 2019 Sierra 1500 Denali w/ 6.2.  Can’t decide between the Borla Touring system or the S-Type.  Don’t really want to wake up my neighbors in the AM every day.  Also what would be the best CAI to use?  Thanks for any help on the subject.

Posted
14 hours ago, John Aragon said:

Need some advice.  Have A 2019 Sierra 1500 Denali w/ 6.2.  Can’t decide between the Borla Touring system or the S-Type.  Don’t really want to wake up my neighbors in the AM every day.  Also what would be the best CAI to use?  Thanks for any help on the subject.

GM Performance and Borla Touring are the same.  S-Type is louder.  I have GM Performance CAI and exhaust on my Trail Boss w/ 6.2.  When I start her up she has a decent bark and rumble until she I either put my truck in D or it's up to temp.  I've asked my neighbors if my truck is loud at startup.  They said they don't even hear it.

Posted

Looking to replace exhaust on a 2019 Sierra Denali w/ 6.2.  Should I put on the Borla Touring or the S-Type system.  Don’t want it too loud but also want to hear it.   Also, what CAI would you recommend?

 

Thanks for the help.

Posted
21 minutes ago, John Aragon said:

If you put in the GM CAI do you have to get the ECM flashed?  The other brands don’t require a flash?  Just wondering.

 

 Thanks 

When I purchased the GM CAI, the directions stated that it had to be flashed by the dealer and there was a code in with it that the dealer used.

  • Like 1
Posted
6 hours ago, John Aragon said:

If you put in the GM CAI do you have to get the ECM flashed?  The other brands don’t require a flash?  Just wondering.

 

 Thanks 

If you don't get it flashed you could end up with a CEL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,716
    Total Members
    8,960
    Most Online
    BDS my HD
    Newest Member
    BDS my HD
    Joined
  • Who's Online   0 Members, 0 Anonymous, 593 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • How about them NICKS!!! 
    • Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...