Jump to content

Speed limiter 98mph??

dan61psu
 Share

Recommended Posts

dan61psu Enthusiast

dan61psu

Posted
Posted

I will admit it is very rare...and the utility is also rare but i hit the speed limiter recently making a pass on the highway around left lane hogs slowing down a ton of traffic.  98mph?  Really?  Most highways around me the typical speed is 80mph.  Feel like my 2011 didnt have this limit...but cant recall

 

Anyone know how to remove the limiter?

batman900 Enthusiast

batman900

Posted
Posted

I believe the previous gen is the same. Thought I had read somewhere that its due to the drive shaft or something not being able to handle the stress of higher speeds. Could be wrong. 

CmackR56 Enthusiast

CmackR56

Posted
Posted

Mine kicks in at 112, which incidentally  is the speed rating of my tires.

 

redwngr Senior Enthusiast

redwngr

Posted
Posted
12 hours ago, dan61psu said:

Hmmmm....how does the computer know what tire rating i have?

Not to tough for them to know what tires it was born with, and of course, that's where the limiter gets set.

 

lt1z Enthusiast

lt1z

Posted
Posted

The the best of my knowlege it is about the factory equipped tire.

20” wheels with 275/60/20 tend to be 112mph
18” wheels regardless of tire 98mph

The 22” 265/50/22 with Alenza tires also 112

MDSilveradoGuy Enthusiast

MDSilveradoGuy

Posted
Posted (edited)
16 hours ago, lt1z said:

The the best of my knowlege it is about the factory equipped tire.

20” wheels with 275/60/20 tend to be 112mph
18” wheels regardless of tire 98mph

The 22” 265/50/22 with Alenza tires also 112

I have the 22” Alenzas, and it shuts down at 107. 

Edited by MDSilveradoGuy
L86 All Terrain Senior Enthusiast

L86 All Terrain

Posted
Posted (edited)

I cant say for certain for these trucks, but on the K2's they were limited because of driveshaft overspeed. The limit was different depending on the transmission and final drive ratio. There were numerous modded truck people saying they had their DS explode around 115mph. Which is not something I would want to experience. As stated, tire speed ratings come in to play. Most quality OEM size All Terrain tires are usually in the 98-112mph range. 

Edited by L86 All Terrain
FishinJ Enthusiast

FishinJ

Posted
Posted
On 10/4/2019 at 3:47 AM, MDSilveradoGuy said:

I have the 22” Alenzas, and it shuts down at 107. 

That sucks, as I was hoping on cruising at 112.  

  • Haha 1
Radchad Enthusiast

Radchad

Posted
Posted (edited)
3 hours ago, FishinJ said:

That sucks, as I was hoping on cruising at 112.  

That’s awesome. Hahahahah@,!,

Edited by Radchad
  • 1 year later...
April Davis New Member

April Davis

Posted
Posted

This is something that my guy just learned about with his 2020 GMS Sierra SLT- this was never disclosed anytime or anywhere  during the selling of this truck.  THIS SHOULD BE  FULL DISCLOSURE to the customer.  Way to go GMC! now this a serious issue not knowing!  At least Corporate knows🤫- not the consumer! 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,949
    Total Members
    8,960
    Most Online
    Gkistler
    Newest Member
    Gkistler
    Joined

  • Who's Online   4 Members, 0 Anonymous, 877 Guests (See full list)

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...