Jump to content

Dimmable footwell lighting

vulcan_classic
 Share

Recommended Posts

vulcan_classic Enthusiast

vulcan_classic

Posted
Posted (edited)

Ok so I started to dig into this and it looks like the only way to tie into the factory wiring is to connect to the BCM dimmer circuit. Based on the 2020 GM upfitter electrical drawings, I may be able to connect the front lights to the dimmer circuit behind the center stack switches, and the rears to the dimmer circuit behind the rear console USB /Aux connectors.

 

The dimmer circuit is designated circuit  # 6817 on the drawings and is YEL wiring. This is most likely a PWM signal since it is variable and controlled by the dimmer controls to the left of the steering wheel at the light switches.

I had success doing this on my 2017 ZR2 using LED strips placed under the dash on both sides and under the rear of the front seats using velcro.

 

First step is to gain access to the center stack without destroying my dash trim! For anyone wanting to do footwell lights operating off the dome lights its almost impossible the way GM has redesigned the dome lights to be controlled from the BCM via the interface logic boards at the lamps in head liner. However, the courtesy function (dome lights and footwell lioghts) will still work but only when driver door is opened, based on how things work in my loaded 2020 AT4. Otherwise any other door opening will onlt turn on the dome lights, unless disabled by the local switch at the overhead lamp location.

 

Stay tuned!

Edited by vulcan_classic
ArTurf Enthusiast

ArTurf

Posted
Posted

Just added footwell lights using this wire, tapped wire with Posi-tap connectors, easy

 

 

ArTurf Enthusiast

ArTurf

Posted
Posted

I have to ask why do they need dimming  if you select lights of the correct brightness to begin with

vulcan_classic Enthusiast

vulcan_classic

Posted
  • Author
Posted (edited)

I want both functions, i.e. dimmer function and nightlighting, i dont see how it would work connecting to the dome lights circuit, i dont drive around with my dome lights on. With the dimmer circuit they will come on with dome lights via the BCM whenever the driver door opens or if you turn on your running lights (instrument backlighting) I have always wired footwell lighting in this way on numerous vehicles.

Edited by vulcan_classic
2k19Sierra Enthusiast

2k19Sierra

Posted
Posted

Wired mine into the aux switches. Nice to have a factory switch to turn em on and off. Use the remote to set the colour and brightness. 

9974F0E7-747A-4B71-A8F9-4A8A3AD60E28.jpeg

PearlyWh1tes Enthusiast

PearlyWh1tes

Posted
Posted (edited)

D0A525F2-63E9-440B-9E7A-0CA6ED0EA1EF.thumb.jpeg.e7a19ea589538552fc59fc30651994dc.jpegJust did it today, wired it to the grey wire(the one not in the corner of the connector) connected to the door sensors on the white connector of the bcm, the lights come on when I open any door, and all for $25. As for dimming, you can wire in a potentiometer/dimmer switch directly into the loop of the lights wiring right before the first light if you really want the option.

A80DBE07-E218-44DA-89E7-7186C9D00B25.jpeg

Edited by PearlyWh1tes
  • Like 1
PearlyWh1tes Enthusiast

PearlyWh1tes

Posted
Posted
On 3/19/2020 at 8:12 AM, vulcan_classic said:

I want both functions, i.e. dimmer function and nightlighting, i dont see how it would work connecting to the dome lights circuit, i dont drive around with my dome lights on. With the dimmer circuit they will come on with dome lights via the BCM whenever the driver door opens or if you turn on your running lights (instrument backlighting) I have always wired footwell lighting in this way on numerous vehicles.

Wire it to the bcm and add in a potentiometer/dimmer switch before the first light

vulcan_classic Enthusiast

vulcan_classic

Posted
  • Author
Posted
On 4/1/2020 at 12:12 AM, PearlyWh1tes said:

Wire it to the bcm and add in a potentiometer/dimmer switch before the first light

I actually wired them as i mentioned previously, YEL wire (#6817) on pin 9 of BCM connector X7, works perfectly, the LED's can be dimmed with the dimmer +/- buttons whenever the instrument back lights are on, and they also come on automatically with driver door opening

Likarok Senior Enthusiast

Likarok

Posted
Posted

These might also make good footwell lights!

 

https://accessories.chevrolet.com/product/exterior/outside-rearview-mirror-puddle-light-kit-with-bowtie-logo-projection-(for-models-with-heated-outside-rearview-power-adjustable-mirrors)-84408372?year=2020&make=Chevrolet&model=Silverado 1500&modelId=491&body=Crew Cab Pickup&bodyId=22&wheel=Short Box&wheelId=651&trim=High Country&trimId=523&drive=4WD&driveId=8&engine=3.0L L6 DIESEL&engineId=17881&bodyNumDoors=5&categoryId=12002

ausomecasey Enthusiast

ausomecasey

Posted
Posted
On 4/10/2020 at 2:05 PM, Likarok said:

These might also make good footwell lights!

 

https://accessories.chevrolet.com/product/exterior/outside-rearview-mirror-puddle-light-kit-with-bowtie-logo-projection-(for-models-with-heated-outside-rearview-power-adjustable-mirrors)-84408372?year=2020&make=Chevrolet&model=Silverado 1500&modelId=491&body=Crew Cab Pickup&bodyId=22&wheel=Short Box&wheelId=651&trim=High Country&trimId=523&drive=4WD&driveId=8&engine=3.0L L6 DIESEL&engineId=17881&bodyNumDoors=5&categoryId=12002

Cool, is that a new GM accessory?

Rubyralph Enthusiast

Rubyralph

Posted
Posted
On ‎4‎/‎7‎/‎2020 at 12:47 PM, vulcan_classic said:

I actually wired them as i mentioned previously, YEL wire (#6817) on pin 9 of BCM connector X7, works perfectly, the LED's can be dimmed with the dimmer +/- buttons whenever the instrument back lights are on, and they also come on automatically with driver door opening

Can you please take a picture to show where the yellow wire is located?

I want my led foot well lights to stay on while driving at night and when I open the doors, this sounds like this would do the trick?!

Thanks Ralph

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I trust you saw the other comment where he knew what he was talking about !. Yes, these darned newer vehicles with all their so smart they are stupid technology, goes and drains the battery down. As you might see my other comment, I installed a Noco 5 battery tender under the hood and at this point still have the cord routed so I have to lift the hood and then plug it in but am typically parked in a garage or a shed so its not risking the engine hood in the wind. That way I am assured or hopefully so of not finding I have a battery drawn down and can't even start the truck and that also damages the battery to draw it down too far. 
    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I guess no surprise my guesses were wrong !, at least now I know if I ever happen to see it grayed out in my own truck as to what is going on.    I never happened to catch my truck with it grayed out, it seemed every time I would test to see if there was an update it never found anything and yet more than once I would check to see if there was an update and there was nothing, then a day later or even that same morning I would drive to town and after more than one engine shut down in town as I did my errands it would pop up that there is an update now ready to install and the only place I have a connection to the internet is at home by wifi so its not as if it grabbed the download while driving. I don't trust these new vehicles due to all the crap they can decide to do while sitting for some days not running and run the battery down so most of the time if I know the truck will sit for a few days I plug in the battery tender I have mounted under the hood and so the only time the truck must have downloaded software was when it was sitting in the garage where the signal is awful but I have that tender plugged in and somehow it managed to download it. I honestly detest all this crap, way to easy to leave a person stranded.    Since I don't trust any of it I don't do the install of the already downloaded software until I get home and sometimes have even sat in the truck to watch what its doing as its going through the process to its conclusion as its not like it is set up that it will tell you the next time you fire up the engine that the update that was initialed actually installed or installed properly. Yes I can go into the updates and see the list. After I go through the install where I feel its safe to do so in case it breaks down as a result, I will plug in the battery tender after the fact to recharge as I don't know how much power its taking just to do the install and that can take a while for it to install. 
    • nfisherman
      Software Update

      By nfisherman · Posted

      Thanks for the reply. All settings were correct and the engine was off, as it was supposed to be. It turned out to be something simple. I took a drive for about an hour. I must have had a low battery without knowing it. The voltage gauge on the display looked ok. At the end of my drive, I shut off the engine and the update prompt came up and it updated normally. It’s ironic because one of the features of the update is a reduction of battery drain. 
    • kickass audio
      Software Update

      By kickass audio · Posted

      when it's greyed out that is it's way of telling you that it's downloading the patch in the background. Eventually it will be fully downloaded and then it will prompt you at ignition shut down to run the update. I highly recommend doing the update once you get home and can run it a few times. I've had several issues with updates not going the first time around and I had to retry the update multiple times in my driveway before it was successful.   Some updates are huge and take awhile to download. You can help it by connecting to your home WiFi and keep the truck on service mode for the ignition and keep it alive for awhile on a battery charger too. There are specs it needs to be in for updating such as a full enough battery charge, no running ignition, etc.
    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I am not techy at all but wondered if you have the truck running but sitting still in park as some functions gray out as soon as the truck is moving. I believe in the settings for updates you can choose for it NOT to update and I wonder by chance if maybe that was chosen before and now it won't allow you to chose to press update, I think that is back in the settings menu where it has all the items one wants on or off etc. Also I assume you have a wifi connection and checked that it has some signal strength, not that it would have anything to do with the grayed out updates choice in that case. What I am thinking out loud of here may be be of no value but thought I would suggest it, sometimes it can be the simplest thing that resolves an issue.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...