Jump to content

Recommended Posts

Posted

I just returned from a 2,000 mile trip. During this trip I put in 5 gallons of DEF (and my GMC is telling me it's ½ full now and I have 1000 miles of DEF range left)... Really??? My 2015 Chevy 2500 HD didn't nearly drink this much DEF. I know emission standards have tightened up a bit, but this seems a bit extreme. Is 7 ½ gallons for 2,000 miles normal? (I'm guessing another 2 ½ gallons based on how much I had to put in last time). The only silver lining is I have a fleet account and can use the trucking lanes for filling up, which have DEF at the pump, but this usage seems way too high. What are others seeing with 2020 models?

Posted

I think 7 and 1/2 gallons is too much for a 2,000 mile trip.  I traveled to New York last month, almost 2,000 miles there and back, and only used about 4 gallons.  What really blows my mind is how a mixture of urine and water costs more than diesel fuel.

Posted

The DEF gauge is NOT a simple variable gauge like a fuel gauge.

It also blends in an estimate of the remaining range (like the range estimate for fuel in the dic).

 

The only way to know miles per def gallon is to fill it, drive it for a few thousand and refill it.  Just like a hand-calc for fuel mileage. 

 

https://gm-techlink.com/?p=13143

 

Diesel Exhaust Fluid Consumption

May 21, 2020

The diesel engines (RPOs LWN, LM2, L5P, L5D) available on 2020 Colorado, Express, Silverado 1500, Silverado 2500HD/3500HD, Silverado 4500HD/5500HD/6500HD, Canyon, Savana, Sierra 1500, and Sierra 2500HD/3500HD models use Diesel Exhaust Fluid (DEF) (Fig. 1) in order to reduce the exhaust Oxides of Nitrogen (NOx) levels within the Selective Catalyst Reduction stage of the exhaust aftertreatment system. A series of driver prompts and warnings are initiated when the DEF level falls below a calibrated value.

 

F01-DEF-1.pngFig. 1

 

Segmented DEF Level Gauge

The current 2020 Silverado 1500 and Sierra 1500 models have a DEF level gauge on the instrument cluster that provides drivers with a representation of how much DEF is in the DEF tank up. (Fig. 2) The DEF level gauge does not operate like a typical float-style gauge that is used in a fuel tank. The Engine Control Module (ECM) monitors the DEF level and consumption rate in order to calculate an estimated range. DEF levels are detected by the DEF level sensor.

 

F02-DEF-2.pngFig. 2

 

There may be some fluctuation in the amount of DEF represented on the DEF level gauge. After filling the DEF tank, it may take a few key cycles to register the correct amount in the DEF tank. With the new segmented DEF level gauge, it is possible that after adding 5 gallons (18.9 L) of DEF that the gauge reads as a full tank after the fill event. However, if the actual level of DEF is just entering the last segment on the gauge, the gauge is likely to drop by one segment shortly after driving after the fill event. As a result, a driver could have an initial impression that the vehicle consumes an excessive amount of DEF.

Emissions Requirements

Every year, GM produces diesel engines that continue to meet aggressive federal requirements to reduce Nitrogen Oxides (NOx) in the vehicle exhaust. As DEF is required to reduce the NOx in the exhaust, DEF consumption will increase as NOx reduction requirements increase. Customer trading in an older model year diesel vehicle for a newer model year vehicle will likely see an increase in DEF usage. DEF consumption increases as the newer vehicles meet the more stringent emission requirements for that model year.
The amount of DEF consumed also is a function of how hard the engine is working, or engine load. Due to engine use, it is more representative to compare DEF consumption to the amount of fuel consumed – also a function of engine load – instead of miles traveled. In addition to engine load, other factors that affect the DEF usage rate are the humidity, temperature, and altitude where the vehicle is operating.

Under certain conditions, the ECM will increase or decrease the amount of DEF used based on learning or adaptive algorithms. In the event of a malfunction and Check Engine light, the ECM may double or even eliminate the amount of DEF that is being used. An improper amount of DEF use will continue until the vehicle is repaired and the learned value in the ECM is reset.

 

 

  • Like 1
Posted

From the way I read the above, there is not a typical tank float level sensor that might get stuck?  I have not added any def to my tank in over 500 miles.  The display when I added went to one bar less than full, but I know it was full at that time.  A day or so later with maybe 100 miles of driving, the display showed full and is still showing full now.  Is this normal? 

Posted
7 hours ago, shadow gray 2020 hd said:

From the way I read the above, there is not a typical tank float level sensor that might get stuck?  I have not added any def to my tank in over 500 miles.  The display when I added went to one bar less than full, but I know it was full at that time.  A day or so later with maybe 100 miles of driving, the display showed full and is still showing full now.  Is this normal? 

I just asked this same question as I am experiencing the same thing...down a square, now full again, even after towing my TR 200+ miles...??

Posted

I too see even full that the DEF gauge shows one bar down. I might have a chat with my local dealer and see what they think. Just seems to me that 7+ gallons for 2,000-ish miles (closer to 2400) is too much.  I do wonder if they need to reset something after reading that bulletin. 

Posted

There’s a service bulletin for this. I had the same issues and haven’t had them since. My sensor reads accurately now. I am burning a lot of DEF fluid compared to previous generation trucks but it’s definitely improved after the service bulletin: sensor is spot on now and mileage has increased.

 

I was getting 300-400 miles per gallon on DEF the first 11k miles and now I’m seeing closer to 700-800 miles per gallon over the last 4K miles after service. Same driving conditions.

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

I have the 2020 Silverado 2500 HD and just got back from a 3700 mile trip towing a ~7000lb travel trailer.  I had to fill my 4.5 gallon DEF tank three times!  It eats DEF like crazy. Mine starts giving me warnings that my DEF range is 975 miles about 150-200 miles after I fill it. Also, about 20 miles from home the DEF gauge went from 3/8 to 0 in one step and told me "DEF low, speed limited soon".   The DEF sensor is seriously goofed up and the 2020 is using a *lot* of DEF.  They did the DEF related software update when I got back but I have not been towing to see if it still uses an exorbitant amount of DEF.

  • Like 1
Posted

Got an appointment for them to look into it today. I'll post how that goes. 

  • Like 1
Posted
On 10/2/2020 at 10:03 AM, cNate said:

There’s a service bulletin for this.

 

Any idea what that bulletin is? My dealer says he can't find anything and service tech looking at the truck can't find anything, so he's saying 7 ½ gallons for a 2200 trip is about right. ? ... I find that hard to believe. Unless you're now carrying boxes of the stuff around all the time or can find stations with DEF at the pump, they are really handicapping folks. I think I'm using way too much.

Posted
 
Any idea what that bulletin is? My dealer says he can't find anything and service tech looking at the truck can't find anything, so he's saying 7 ½ gallons for a 2200 trip is about right. [emoji44] ... I find that hard to believe. Unless you're now carrying boxes of the stuff around all the time or can find stations with DEF at the pump, they are really handicapping folks. I think I'm using way too much.

049e8de0415dc9ba6900ea37d197f1e9.jpg


Sent from my iPhone using Tapatalk
Posted

My dealership had no idea either. I asked them to search for it based on a post I read on another forum and they found. See number in photo I posted.


Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Thanks, all. It sounds like keeping the software "as is" is the best course of action.
    • https://en.wikipedia.org/wiki/Overengineering   Excerpt from the above link: (BTW the above is a 90 second read)   [Quote]   A story about very precise engineering is given in the 1858 story The Deacon's Masterpiece or, the Wonderful "One-hoss Shay": A Logical Story by Oliver Wendell Holmes Sr., which tells of a carriage (one-horse shay) Because it had been engineered so that no single piece failed first – no piece was over-engineered relative to the others, and they thus all collapsed at the same time. A similar quote by Ferdinand Porsche claimed "the perfect race car crosses the finish line in first place and immediately falls into pieces."[5]   [End Quote}   By Engineering's  own definition then; the AFM and Torque Converters, 4-5-6 clutch assembly of the 6L80E, and a dozen other common chronic parts and systems failures are "UNDER ENGINEERED". And by their own definition done so with INTENT. Ya can't have it both ways OEM's.     
    • Everything you need to know..... https://www.gm-trucks.com/forums/topic/198157-2014-2017-dl8-dl3-towing-mirror-upgrade-–-mirrors-explained/
    • I was in Utah this week attempting a bow hunt in the Wasatch mountains with friends.  On the evening of the first hunt, making my way across a ridge to a friends camp, the upper control arm on the driver's side separated, the CV axle got trashed, and the wheel was dang near at a 45 degree angle to the ground.  I was able to get it towed off the mountain and into town about 3:00 am, and spent the remainder of the night in an O'Reilly's parking lot.  Luckily, there was a Chevrolet dealership not to far away so I was able to get to the dealership and pick up a new CV and UCA.  It would have been a few days before they could have gotten to the truck and I brought tools with me on hunt since it was a two day drive to get there, so I did the repairs myself in the O'Reilly's parking lot.      What's interesting is that the UCA ball joint didn't break, it just popped out of the bottom of the UCA.  There was VERY LITTLE evidence of grease on the ball joint or in the socket, and you could see where the ball joint had warbled out part of the socket over time.  I guess that's what happens over 186K miles of use :)   Big Kudos to O'Reilly's for letting me work on the truck in their parking lot.  However, they made a $150+ off of me from the purchase of various tools, so I guess it was in their best interest anyways :)   Getting towed off the mountain.   UCA Ball Joint Socket   Trashed CV   Suspension disconnected and UCA and CV Removed   New UCA and CV installed with the suspension buttoned up.    
    • My family still laughs at me when they see me drive up in the minivan. Same with less than a V-8 truck. It helps that I have choices. I don’t think I could only have a minivan as the one and only vehicle as much as I like it. And I wouldn’t pass up a good buy on an older V-8 reg cab GM truck. Could you live Raven as the only ride?
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...