Jump to content

Multi Pro Tailgate Replacement!

Cris805

By Cris805
in Modifications, Wheels & Tires

 Share

Recommended Posts

Cris805 New Member

Cris805

Posted
Posted

Hello,

I have a 2020 sierra Elevation with standard tailgate. I was wondering if I can replace it with a multi pro tailgate, if it'll just be a plug and play with my stock harness or what can i do to make it work. I have a local seller here selling it for $500 came from his denali. Thank you in advance 

Gangly Senior Enthusiast

Gangly

Posted
Posted

Even if it doesn't work on your truck, purchase it and you can turn around and sell it for double easily.

eppieguy Senior Enthusiast

eppieguy

Posted
Posted (edited)

I do believe someone talked about this once and the tailgate is a different width? IIRC

Edited by eppieguy
  • 10 months later...
Delmster Enthusiast

Delmster

Posted
Posted

I really need a center section of the multipro tailgate. Preferably in satin steel metalic. Tailgate mysteriously went down while hauling a car trailer and when turning, tailgate got into the  tongue jack. Still works just makes my 2021 at4 look "not new"

GETGONE Enthusiast

GETGONE

Posted
Posted

You can't just add it. My dealer looked into it when they were trying to find a Trail Boss Custom with the MultiFlex tailgate. The box wiring harness is totally different for the tailgate and in order to add it would run about $3K.

Rob Mugs Enthusiast

Rob Mugs

Posted
Posted
On 9/22/2021 at 4:40 PM, GETGONE said:

You can't just add it. My dealer looked into it when they were trying to find a Trail Boss Custom with the MultiFlex tailgate. The box wiring harness is totally different for the tailgate and in order to add it would run about $3K.

That's likely with the cost of the tailgate at OEM prices.  I'd personally take Gangly's advice if it's the same color.

  • 4 weeks later...
Zas New Member

Zas

Posted
Posted

So I picked up a 2021 AT4 Multipro Tailgate in my trucks color for $600, bought the camera/buttons assembly and the non surroundview harness. He kept the camera/buttons assembly and harness to keep the surroundview working. I assembled and installed and the midgate does not function. Hearing that this might BCM programming issue. Anyone have any advice on a programmer that can turn the feature on?

  • 6 months later...
Sharpie Enthusiast

Sharpie

Posted
Posted

I just did a multi-pro swap for my 22 Silverado and it was relatively easy.  Luckily all of the wiring and relays were there for the minor gate.  For starters I cut the ground wire to the mid gate switch.  I needed to get 12V to this.  (I know I am talking ground and 12V, but stay with me here...)  At the Chassis side of the tailgate harness there is 12V Battery at Pin 1.  this was ran for trucks with the power up option.  My truck had the fuse and ckt already.  So I cut the lead out of the connector and ran a new wire up through the tailgate following the factor harness and connected it to the ground side of the pin on the minor gate switch.  The other end of the switch is the yellow lead that goes back to the BCM to signal the button was pressed.  Again I happen to have the minor gate relays and wiring on my standard gate LTZ, so I don't know what other trims it was also there. I needed to use this new 12V ckt I made to go direct to the two relays top drop the minor gate.  At the BCM I cut the Yellow switch wire (Pin X6-15) and connected it to relay outputs White/Gray (Pin X6-7) and Gray/Blue (Pin X7-7).  From the BCM this relay output was power to ground.  So by starting my switch at the 12V+ I just created a new ckt though the switch to the relays and down to GND.  I did pull the 30A endgate fuse while I was doing all this.  It all works!  The only downside is when the vehicle is locked, this ckt is still powered and will open upon press. I have the factory up fitter switches too, so I think I will use one of them as a disable possibly.  Should be really easy as the BCM is right below the upfitter switches.  The multipro I got was the same color truck but a GMC.  I still need to swap the emblems.  Waiting on a good sunny warm day to make that chore a little easier. 

  • Like 3
Gangly Senior Enthusiast

Gangly

Posted
Posted
1 hour ago, Sharpie said:

I just did a multi-pro swap for my 22 Silverado and it was relatively easy.  Luckily all of the wiring and relays were there for the minor gate.  For starters I cut the ground wire to the mid gate switch.  I needed to get 12V to this.  (I know I am talking ground and 12V, but stay with me here...)  At the Chassis side of the tailgate harness there is 12V Battery at Pin 1.  this was ran for trucks with the power up option.  My truck had the fuse and ckt already.  So I cut the lead out of the connector and ran a new wire up through the tailgate following the factor harness and connected it to the ground side of the pin on the minor gate switch.  The other end of the switch is the yellow lead that goes back to the BCM to signal the button was pressed.  Again I happen to have the minor gate relays and wiring on my standard gate LTZ, so I don't know what other trims it was also there. I needed to use this new 12V ckt I made to go direct to the two relays top drop the minor gate.  At the BCM I cut the Yellow switch wire (Pin X6-15) and connected it to relay outputs White/Gray (Pin X6-7) and Gray/Blue (Pin X7-7).  From the BCM this relay output was power to ground.  So by starting my switch at the 12V+ I just created a new ckt though the switch to the relays and down to GND.  I did pull the 30A endgate fuse while I was doing all this.  It all works!  The only downside is when the vehicle is locked, this ckt is still powered and will open upon press. I have the factory up fitter switches too, so I think I will use one of them as a disable possibly.  Should be really easy as the BCM is right below the upfitter switches.  The multipro I got was the same color truck but a GMC.  I still need to swap the emblems.  Waiting on a good sunny warm day to make that chore a little easier. 

I KNEW IT.  I had a GM guy telling me at the Auto show that the GMC tailgates wouldn't physically fit on the Silverado, and that neither the GMC or Silverado adjustable tailgate would fit on a truck that didn't come from the factory with it.  I called BS and he couldn't tell me why.  Thanks for doing us all a service Sharpie.

redwngr Senior Enthusiast

redwngr

Posted
Posted

The place there is a fit issue is 2500/3500 vs 1500.

The heights are different.

 

 

Sharpie Enthusiast

Sharpie

Posted
Posted
5 hours ago, redwngr said:

The place there is a fit issue is 2500/3500 vs 1500.

The heights are different.

 

 

Yea I meant to mention that too.   All Chevy/GMCs for 2500/3500 are the same and all 1500's are the same, but NOT interchangeable.   Thanks Redwngr.  I'll also mention the only Bowtie that seemed to be for a HD Chevy w/ muli-flex was the black bowtie.  I ended up buying a 1500 gold bowtie and I'll stick that on. 

GETGONE Enthusiast

GETGONE

Posted
Posted

So is yours you did the swap on a 1500 or a 2500/3500?

Sharpie Enthusiast

Sharpie

Posted
Posted

My Silverado is a 22 3500 Dually LTZ Trim. I guess I need to add that to my profile. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,938
    Total Members
    8,960
    Most Online
    C. Hart
    Newest Member
    C. Hart
    Joined

  • Who's Online   4 Members, 0 Anonymous, 592 Guests (See full list)

  • Latest Articles

  • Posts

    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks everyone for the help!   I'm going to stop into the scales one of these days and weigh my axels, for the time being, I am going to run Toyo's recommendations and also do a chalk test. I have a tire shop that's going to try their scanner to reprogram and set the the factory psi values lower, and if they can't I'm going to order a scanner and do it myself!
    • KARNUT
      Exhaust Question

      By KARNUT · Posted

      You won’t do better than stock exhaust without headers. Just put your favorite muffler on it and it will do the job. 
    • C. Hart
      Exhaust Question

      By C. Hart · Posted

      I have seen different people in different places post different sizes of exhaust as stock for my 2014 Sierra L83. Some say 2.5 some say 2.75. I am considering replacing the muffler with a Dynomax Super Turbo, perhaps 17739.  I had the factory L83 5.3 replaced with another L83 5.3 from Jasper Engines. I also put new Walker Cat / Y pipe on. I would appreciate opinions suggestions about what would be a good muffler setup. My main interest is a low rumble and the best flow / fuel mileage I can get. Not interested in straight through glass packs or loud exhaust. Those days are way behind me now.  Thanks Guys.  
    • newdude
      Cold start Miss, oil in cylinder

      By newdude · Posted

      Its coolant disguised as oil.   TSB 20-NA-166 -  20-NA-166 1..3   "To inspect for this concern, add coolant dye to the system, run the engine through warm up, pressurize the cooling system after warming the engine to operating temperature (let the engine cool overnight) and inspect the suspect cylinder with a borescope for coolant dye evidence. At times it may be necessary to remove the head for inspection. If the head casting line is the concern, the intake port will be wet with a coolant oil mix"     I'd say its the head, and its either leaking at the casting line and dripping down the intake into the cylinder, or its another spot on the casting itself at the cylinder that is getting wet.  
    • asilverblazer
      Cold start Miss, oil in cylinder

      By asilverblazer · Posted

      Can you sample the pooled liquid, enough to confirm it is oil?   ...That its not fuel or coolant.   Also, make sure combustion gases aren't entering the cooling system.   Simply put, either oil being pushed up past the rings (this really isn't possible), oil leaking past the head gasket, oil leaking past the valve, oil entering through the intake air path. If none of this is likely - it may not be oil.   What could be likely is the fuel injector leaking down. A puddle of gas would still smoke and rough idle. (Same cylinder has the same problem after injector replacement?)   What is the crank time first thing in the morning, when the puddle would be present? Does it seem like the high pressure fuel pump needs an extra second or two to rebuild the pressure that injector 8 may have let bleed off? Check the fuel pressure via a scanner prior to starting the engine.    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...