Jump to content

Lower ball joint stuck

Bryant Wray
 Share

Recommended Posts

Bryant Wray Enthusiast

Bryant Wray

Posted
Posted

I am trying to replace lower ball joints on my 2014 Silverado 1500 Z71. The drivers side is very stuck. I have broke everything else loose, I just cannot get the lower ball joint busted loose from the steering knuckle. I have tried the tuning fork and the separator clamp. The clamp does not expand far enough to track the bottom of the ball joint stud. Any ideas? This has been too many days trying to figure this out. 

5A462E77-C321-439F-B21F-6E4975D5CEDB.jpeg

717579F6-4C38-4780-A569-BA13D904B69B.jpeg

F87E5CC6-CA37-47E0-BEFD-CD7BAB273A6C.jpeg

  • Sad 1
CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Heat the knuckle with a propane or map gas torch. You likely need to expand the metal that is around the ball joint stud. Do that for a while to get it nice and hot, then use a ball joint fork to try and get it out.

  • Like 1
richard wysong Senior Enthusiast

richard wysong

Posted
Posted

Strike the side of the knuckle adjacent to the taper with a large hammer and that will pop it, may take multiple blows

  • Like 2
  • Thanks 1
mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted

Another agreement on a BFH. I used a mini sledge when needed and several real strong hits on the side always got it separated for me. Don't hold back and whack it good.

  • Like 1
Bryant Wray Enthusiast

Bryant Wray

Posted
  • Author
Posted

Used a 4lb sledge, didn’t bust it loose. Any other ideas? I got a ball joint separator from the parts store but the notch is not wide enough to go around the ball joint. Do they make bigger ones?

Buckwild27 Enthusiast

Buckwild27

Posted
Posted
18 minutes ago, Bryant Wray said:

Used a 4lb sledge, didn’t bust it loose. Any other ideas? I got a ball joint separator from the parts store but the notch is not wide enough to go around the ball joint. Do they make bigger ones?

Air hammer. 

  • Like 1
txab Senior Enthusiast

txab

Posted
Posted
27 minutes ago, Bryant Wray said:

Used a 4lb sledge, didn’t bust it loose. Any other ideas? I got a ball joint separator from the parts store but the notch is not wide enough to go around the ball joint. Do they make bigger ones?

How wide is the notch? Mine is at least 15/16" wide

  • Like 1
richard wysong Senior Enthusiast

richard wysong

Posted
Posted

7/16? That makes no sense, 7/8 maybe? Sounds like you got a tie rod fork, return it and get a BJ fork

  • Like 2
Bryant Wray Enthusiast

Bryant Wray

Posted
  • Author
Posted
10 minutes ago, richard wysong said:

7/16? That makes no sense, 7/8 maybe? Sounds like you got a tie rod fork, return it and get a BJ fork

Correct, 7/8, my mistake

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted
On 4/8/2023 at 10:57 AM, Bryant Wray said:

I am trying to replace lower ball joints on my 2014 Silverado 1500 Z71. 

 

Stop by my house and borrow my J-43631 and torture yourself no more.

Kent Moore Ball Joint Puller Tool J-43631 (cs1354 802 B3 for sale ...

 

 

 

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • kickass audio
      Software Update

      By kickass audio · Posted

      when it's greyed out that is it's way of telling you that it's downloading the patch in the background. Eventually it will be fully downloaded and then it will prompt you at ignition shut down to run the update. I highly recommend doing the update once you get home and can run it a few times. I've had several issues with updates not going the first time around and I had to retry the update multiple times in my driveway before it was successful.   Some updates are huge and take awhile to download. You can help it by connecting to your home WiFi and keep the truck on service mode for the ignition and keep it alive for awhile on a battery charger too. There are specs it needs to be in for updating such as a full enough battery charge, no running ignition, etc.
    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I am not techy at all but wondered if you have the truck running but sitting still in park as some functions gray out as soon as the truck is moving. I believe in the settings for updates you can choose for it NOT to update and I wonder by chance if maybe that was chosen before and now it won't allow you to chose to press update, I think that is back in the settings menu where it has all the items one wants on or off etc. Also I assume you have a wifi connection and checked that it has some signal strength, not that it would have anything to do with the grayed out updates choice in that case. What I am thinking out loud of here may be be of no value but thought I would suggest it, sometimes it can be the simplest thing that resolves an issue.  
    • Chuck FB
      Dave's Auto (custom engine builder) tear down of L8T

      By Chuck FB · Posted

      The so called rare failure that some certainly liked to tout ( die hard Ford fan boys ) as per the lifter failing and wiping out the cam. Back when it started happening the blame was being pointed to the lifters and honestly I never did hear anything myself conclusively one way or the other on that. Ford themselves in I believe 2024 had a technical bulletin I will call it that came out and for some engine platforms they were reprograming the engines idle speed but also they had a software update for the oil pump which then some time later was said what that software update did as to be increasing the oil pressure at idle. It is a good question if that issue was completely solved as one Ford specialist mechanic youtuber said he saw failures after that time period. Like anything there would be the variables, what oil is being used and the OCI and how much idle time gets put on an engine. I've seen some comments to claim that the L8T isn't so happy with high idle time either but I also know that companies that require their vehicle to idle a lot on the job don't tend to get the oil changed often enough for all those hours of idle time and go off of the odometer. 
    • bwiese
      Lower trims ( WT, Custom, Silverado ( aka LT )

      By bwiese · Posted

      My 2026 Silv. 1500 WT (reg cab/short bed/4wd) has the 40/20/40 with storage in lower middle seat as well as the fold-down center bolster/armrest.   With the dual glove boxes this is about as much storage as possible in a std cab IMHO. Bill
    • bwiese
      2026 Silv. 1500 WT reg cab: how many speakers do I have? Is amp module separate?

      By bwiese · Posted

      I have a 2026 base 1500 "WT" regular cab with basic Chevy "Infotainment 3" 7-inch screen/radio. How many speakers do I have If I want to upgrade? Is the audio amp separate from the radio/display unit]? [I listen to classical and it gets a bit raspy at slightly higher volumes. Don't need a sub etc.] Do I have two or 1 speakers in the doors? etc. Thanks Bill  San Jose

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...