Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

bcbz71 Enthusiast

bcbz71

Posted
Posted

Any of you guys have any shortcuts or pointers on installing the lower blocks of the RC 2.5 level? Didn't find many good quality videos. This kit, as bad as I hate to say it, kicked my a$$ tonight! I got the top spacers in but I pretty much did everything short of disassembling the whole entire front end tonight.

 

After spending a few hours doing my AMP Research steps, I decided to tackle the level also... Now I wish I hadn't! I am admitting defeat and bowing out gracefully! I'm not new to suspension work, but its mostly been limited to coilovers on sports cars, never any lifts or levels.

 

Jack one side up and support with jackstands.

Take off tire.

Disconnect steering joint.

Disconnect brake line on upper control arm

Disconnect sway bar nut or at least back the nut off as far as you can.

Discconnect upper ball joint nut (UCA)

Discconnect top strut nuts

Discconnect bottom strut bolts and pry off nutplates and discard.

 

Put in top spacer but only put the nuts on top of the strut on very loosely so you have play for the bottom.

Put in the bottom spacer with bolts from the top--threads down. I remember having to pry a little to get the holes lined up, but not bad.

 

The hardest part to me was compressing the strut to get the upper ball joint nut started. I hooked a ratchet strap to the top of the strut and the lower control arm until I could get the ball joint nut (UCA) started.

 

http://www.silveradosierra.com/suspension/2-5-rc-level-kit-install-2014-gmc-sierra-t350650.html

  • Like 1
  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

gSwift Enthusiast

gSwift

Posted
Posted (edited)

Jack one side up and support with jackstands.

Take off tire.

Disconnect steering joint.

Disconnect brake line on upper control arm

Disconnect sway bar nut or at least back the nut off as far as you can.

Discconnect upper ball joint nut (UCA)

Discconnect top strut nuts

Discconnect bottom strut bolts and pry off nutplates and discard.

 

Put in top spacer but only put the nuts on top of the strut on very loosely so you have play for the bottom.

Put in the bottom spacer with bolts from the top--threads down. I remember having to pry a little to get the holes lined up, but not bad.

 

The hardest part to me was compressing the strut to get the upper ball joint nut started. I hooked a ratchet strap to the top of the strut and the lower control arm until I could get the ball joint nut (UCA) started.

 

http://www.silveradosierra.com/suspension/2-5-rc-level-kit-install-2014-gmc-sierra-t350650.html

Thanks for the reply. Top spacers were no problem. It was the rear bolt by the axle that had me kinda baffled. The directions said something like, you may have to move the knuckle to one side to gain clearance from the axle, or something like that. The lower control arm was bottomed out as low as it would go, and there's no moving the axle. I'm about ready to just have it done somewhere. I live out in the country so all my friends are 50 plus miles away. So needless to say, I was pretty frustrated! Edited by gSwift
arkenzo Enthusiast

arkenzo

Posted
Posted

Just front spacer.

Did you get a wheel alignment after? Was it necessary for just the top spacer?

2fst4u Enthusiast

2fst4u

Posted
Posted

I used the readylift video on YouTube. It is simple video on how to put there 2.25 leveling kit on but very similar to the rc kit. Took me about 3 hours from start to finish.

2fst4u Enthusiast

2fst4u

Posted
Posted

Sorry forgot to say I used this video to do my rc kit on the 16 gm and worked like a charm.

gSwift Enthusiast

gSwift

Posted
Posted

Well, the ready lift video showed me everything except for the lower block installation...which is what I need. The bolt by the axle seems so long that I see no way of getting the bolt in. I can get it in from the bottom up all day long. I'm beyond frustrated trying to get this lower block in.

arkenzo Enthusiast

arkenzo

Posted
Posted

Well, the ready lift video showed me everything except for the lower block installation...which is what I need. The bolt by the axle seems so long that I see no way of getting the bolt in. I can get it in from the bottom up all day long. I'm beyond frustrated trying to get this lower block in.

Show pics of what you are working with please. I've installed a full RC 2.5 on my previous 2014 Silverado and I managed to do it all with simple tools and a 1/2 ton floor jack lol, i'm willing to guide you but would need to see what you're seeing.

gSwift Enthusiast

gSwift

Posted
Posted

Show pics of what you are working with please. I've installed a full RC 2.5 on my previous 2014 Silverado and I managed to do it all with simple tools and a 1/2 ton floor jack lol, i'm willing to guide you but would need to see what you're seeing.

 

I appreciate the offer and the replies, but I called it quits and put the front end back together. As I mentioned before, i'm certainly not new to suspension work, but this one got the best of me. I'll take it to a local off road shop as bad as I hate to.

gSwift Enthusiast

gSwift

Posted
Posted

Show pics of what you are working with please. I've installed a full RC 2.5 on my previous 2014 Silverado and I managed to do it all with simple tools and a 1/2 ton floor jack lol, i'm willing to guide you but would need to see what you're seeing.

But just to try and clear up what I'm saying. The main thing that was giving me trouble was mounting the bottom block on the bottom of the shock. I calls to put the new bolt in from the top side, and I can get the bolt in on the hole nearest to the front of the truck. But the back hole of the shock is almost directly under the axle. Therefore the is trying to go in at a hard angle but the head of the bolt is hitting the axle.

Tim Rasmussen Enthusiast

Tim Rasmussen

Posted
Posted

But just to try and clear up what I'm saying. The main thing that was giving me trouble was mounting the bottom block on the bottom of the shock. I calls to put the new bolt in from the top side, and I can get the bolt in on the hole nearest to the front of the truck. But the back hole of the shock is almost directly under the axle. Therefore the is trying to go in at a hard angle but the head of the bolt is hitting the axle.

All bolts I put in on my readylift kit had them going in from the bottom up. This allowed for me to reuse the threaded clips that are connected to the shocks that act like a nut you could say. So for u to put them in from the top down makes me wonder how you would be able to use the factory threaded clip? Did the send nuts to go on the bottom of the spindle?

 

I would suggest putting the bolt in from the bottom up. My two cents.

gSwift Enthusiast

gSwift

Posted
Posted (edited)

All bolts I put in on my readylift kit had them going in from the bottom up. This allowed for me to reuse the threaded clips that are connected to the shocks that act like a nut you could say. So for u to put them in from the top down makes me wonder how you would be able to use the factory threaded clip? Did the send nuts to go on the bottom of the spindle?

 

I would suggest putting the bolt in from the bottom up. My two cents.

 

You don't use the threaded clip on the RC kit. You just pop the clips off and then they supply you with new bolts and nuts. Your kit sounds like it makes more sense. And I could go in from the bottom, but the bolt is so long and the lock nut so thick that its jamming into the bottom of the axle.

 

Guess i'll just leave it to the pro's haha

Edited by gSwift
bcbz71 Enthusiast

bcbz71

Posted
Posted (edited)

 

You don't use the threaded clip on the RC kit. You just pop the clips off and then they supply you with new bolts and nuts. Your kit sounds like it makes more sense. And I could go in from the bottom, but the bolt is so long and the lock nut so thick that its jamming into the bottom of the axle.

 

Guess i'll just leave it to the pro's haha

 

The bolts have to go in from the top. I think the problem is that you didn't take off the UCA nut completely and drop the hub.. I had the same issue. I tried to leave it on by one thread and pry the lower spacer in under the strut. Once you take the UCA nut off and the steering tie rod end off, you can articulate the hub any direction you want to get the bolt in.

 

As I think about it, I may have done the bottom spacer before the top spacer. The first side took me forever it seemed, but the second side was like 30 minutes total.

 

Here is my strut down before I took off the UCA and dropped it completely.

post-138034-0-71029700-1459082514_thumb.jpg

post-138034-0-71029700-1459082514_thumb.jpg

post-138034-0-71029700-1459082514_thumb.jpg

post-138034-0-71029700-1459082514_thumb.jpg

Edited by bcbz71
gSwift Enthusiast

gSwift

Posted
Posted

 

The bolts have to go in from the top. I think the problem is that you didn't take off the UCA nut completely and drop the hub.. I had the same issue. I tried to leave it on by one thread and pry the lower spacer in under the strut. Once you take the UCA nut off and the steering tie rod end off, you can articulate the hub any direction you want to get the bolt in.

 

As I think about it, I may have done the bottom spacer before the top spacer. The first side took me forever it seemed, but the second side was like 30 minutes total.

 

Here is my strut down before I took off the UCA and dropped it completely.

 

That may indeed be the issue. I was leaving the UCA nut attached, and by more than a thread or two. It seems as if I had watched a video where they took a couple of shortcuts and left that nut attached. But now that I think about it, I believe they went in from the bottom with the new bolts on the lower spacer.

 

Thanks for the reply! I think i'll give this one more try before I give up.

 

If only I had followed the directions word for word :banghead:

  • Like 1
arkenzo Enthusiast

arkenzo

Posted
Posted

 

 

 

If only I had followed the directions word for word :banghead:

Get'er done!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,943
    Total Members
    8,960
    Most Online
    Dom Colussi
    Newest Member
    Dom Colussi
    Joined

  • Who's Online   2 Members, 0 Anonymous, 483 Guests (See full list)

  • Latest Articles

  • Posts

    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      It also depends on what criteria someone is using for “best” when talking filters.  Are we going off best efficiency?   Best quality/QC?  Etc. because the two may not mutually exclusive.  
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      They’re not the same wiz as 10-15 years ago.  QC has fallen pretty hard.  The XP line was never good though in the first place.    https://bobistheoilguy.com/forums/threads/wix-filter-rusted-through.386492/post-6991372   https://bobistheoilguy.com/forums/threads/i-ve-used-my-last-wix-filter.27299/   https://bobistheoilguy.com/forums/threads/looking-for-a-better-replacement-for-wix-51258.403977/   https://bobistheoilguy.com/forums/threads/convince-me-in-using-the-purolator-boss.401537/post-7420147   the forums are littered with posts and examples of not great wix filters the last couple years 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...