Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

spenpet Enthusiast

spenpet

Posted
Posted
On 4/1/2018 at 4:34 PM, Paintball Dad said:

Hey guys. New here to the forums. This may have been discussed... I have looked through some pages and honestly cant get past looking at the pictures of all the awesome trucks builds! I have a 2014 Sierra 1500 4WD Crew Cab. I want to level the truck by lowering the rear. I don't haul anything heavy or tow. However, I have to remember Mom & Dad need to get in sometimes. :lol: I was told removing the stock blocks under the leaf springs would level it with the front. Is this true? Or, is the better option to buy the lowering shackles? Thanks in advance!

Level up the front and get steps/running boards! :)   personally I would never lower a 4wd...but thats just me...welcome to the forum, good luck with your truck!

  • Like 1
BayouBound New Member

BayouBound

Posted
Posted (edited)

Installing a 2" RC leveling kit this weekend on my 2016 Silverado 1500.  Does anyone know if 285/55R20 BFG KO2 on stock wheels will fit with little to no rub?

 

Or maybe the better question, what is the largest size BFG K02 I could run on stock 20" wheels with a 2" RC leveling kit? I'd prefer to stay away from large wheel spacers if possible.

Edited by BayouBound
Silveradoh Enthusiast

Silveradoh

Posted
Posted
Installing a 2" RC leveling kit this weekend on my 2016 Silverado 1500.  Does anyone know if 285/55R20 BFG KO2 on stock wheels will fit with little to no rub?
 
Or maybe the better question, what is the largest size BFG K02 I could run on stock 20" wheels with a 2" RC leveling kit? I'd prefer to stay away from large wheel spacers if possible.



Should be pretty safe with 285/55/20, you could maybe go up to 295/55, but you’d probably have to do some minor trimming to get to zero rub.


Sent from my iPhone using Tapatalk
MOhunter92 Enthusiast

MOhunter92

Posted
Posted
Installing a 2" RC leveling kit this weekend on my 2016 Silverado 1500.  Does anyone know if 285/55R20 BFG KO2 on stock wheels will fit with little to no rub?
 
Or maybe the better question, what is the largest size BFG K02 I could run on stock 20" wheels with a 2" RC leveling kit? I'd prefer to stay away from large wheel spacers if possible.


285/55 should be fine, I wouldn’t go anything above that though. I’m on +18 wheels and 285/55r20s with a 2.5 level and I can tell you too much bigger and I would rub. I still want to do some testing because I feel like I feel rubbing at full crank but it could just be the knobbier new tires I have now causing that sensation.

I can tell you a lottt of guys will tell you no rubbing or little rubbing on the more aggressive set ups aren’t telling the full truth. If I went with a more negative offset on these it would rub for sure, and they aren’t too much bigger than stock. They definitely look great though, I can’t tell any difference really looking at these and 33x12.50 on friends trucks. Same height just a tad narrower.


Sent from my iPhone using Tapatalk
spenpet Enthusiast

spenpet

Posted
Posted
21 hours ago, BayouBound said:

Installing a 2" RC leveling kit this weekend on my 2016 Silverado 1500.  Does anyone know if 285/55R20 BFG KO2 on stock wheels will fit with little to no rub?

 

Or maybe the better question, what is the largest size BFG K02 I could run on stock 20" wheels with a 2" RC leveling kit? I'd prefer to stay away from large wheel spacers if possible.

https://tiresize.com/calculator/

 

the 285/55/20 is actually slightly shorter than the 285/65/18...both will fit without any rubbing with a 2'"level up.  as far as the largest...you are getting pretty close to that (without some little mods)...

 

i believe they make a 275/60R20 now....and i would think that would be the ideal and perfect fit...BUT that would probably take a little trimming of the carpet wheel liner, but that isn't a big deal... others might have a better answer for you...

Big Whiskey Senior Enthusiast

Big Whiskey

Posted
Posted
On 4/1/2018 at 4:34 PM, Paintball Dad said:

Hey guys. New here to the forums. This may have been discussed... I have looked through some pages and honestly cant get past looking at the pictures of all the awesome trucks builds! I have a 2014 Sierra 1500 4WD Crew Cab. I want to level the truck by lowering the rear. I don't haul anything heavy or tow. However, I have to remember Mom & Dad need to get in sometimes. :lol: I was told removing the stock blocks under the leaf springs would level it with the front. Is this true? Or, is the better option to buy the lowering shackles? Thanks in advance!

I'm not a fan of lowering trucks.....but the rear block is 1.25". So, removing that will lower the rear 1.25". Most trucks have 2"-2.5" of rake, so you probably won't end up exactly level...but you'll have less rake than you do now. I'd say try that first, and see how you like it. You could always add a small leveling kit to the front in the future if you wanted. That being said, trucks that are "exactly level" have always looked nose-high to me for some reason.

On 4/3/2018 at 9:21 AM, BayouBound said:

Installing a 2" RC leveling kit this weekend on my 2016 Silverado 1500.  Does anyone know if 285/55R20 BFG KO2 on stock wheels will fit with little to no rub?

 

Or maybe the better question, what is the largest size BFG K02 I could run on stock 20" wheels with a 2" RC leveling kit? I'd prefer to stay away from large wheel spacers if possible.

285/55/20 should fit without any trouble at all. In fact, they'll probably fit without any lift at all. If you're wanting to run BFG AT's, then I'd recommend the 275/60/20 because of the extra height. They should fit fine with a 2" level. 

thutchi3 Enthusiast

thutchi3

Posted
Posted

So I have the 2.5" kit coming tomorrow. The step that uses the 21mm wrench...can I use a 21mm socket? I have the socket but not the wrench. I have all the other tools. I can buy a wrench if needed, just would rather use what i have.

math_10silverado Enthusiast

math_10silverado

Posted
Posted

for removal with a deep socket yes... for reinstall if the ball join spin you wont be abble to hold it from the bottom with a 10mm wrench

thutchi3 Enthusiast

thutchi3

Posted
Posted
On 4/4/2018 at 9:46 PM, math_10silverado said:

for removal with a deep socket yes... for reinstall if the ball join spin you wont be abble to hold it from the bottom with a 10mm wrench

Put the level on last night. It's the steering linkage that uses a 10mm wrench (if it spins while reinstalling). The ball joint is a 7/32 allen for those doing this in the future.

 

On a side note, it was late so I didn't put the rear block in. Like a dummy I didn't have all my tires inflated to the same PSI so my initial measurements were off. Now the front is higher than the rear. Tires are all the same now, and as soon as I add the rear block I'll post up pics and measurements. Thanks for all the help so far guys.

JSB81 Enthusiast

JSB81

Posted
Posted
On 3/11/2018 at 6:20 PM, JSB81 said:

I have a 2018 Seirra Denali 1500 with a 6.2 and added a RC 2.5” leveling kit. With leveling kit in and when 4 wheel drive engaged it have a pretty good vibration when engine is under a load. Anyone else have this? Take leveling kit out and it goes away. 

Finally got all my issues fixed. 90% of my problem was in front driveline. Brought it to a drive line place and there was a curve in it. So much so they wouldn’t balance it. (GM) says it’s within range of normal ?. Had them build me a new driveline. The other 10% were in the tires. I had 295 55 toyo. Went to a 285 55 hankook and all my problems went away! Was thankful the dealer picked up entire bill except tire exchange. Just thought I would throw it out there if anyone else comes across this. My dealer found another truck on their lot with same drive line issue after I told them about mine. 

  • Like 1
bcbz71 Enthusiast

bcbz71

Posted
Posted
On 4/8/2018 at 9:20 AM, MHardiman90 said:

Finally received my BORA 1.25" spacers. Glad to report no more rub while on a 2.5" motofab level with 33x12.50's on stock AT wheels!IMG_20180407_104530.thumb.jpg.6eb1d241e09b4bd3e72ce2b59efa2438.jpg

That looks great.   I've heard you can run 1" spacers without trimming the studs if you have the pockets in back of your wheels.  

 

They are 20" rims on your truck, right?

MHardiman90 Enthusiast

MHardiman90

Posted
Posted (edited)
24 minutes ago, bcbz71 said:

That looks great.   I've heard you can run 1" spacers without trimming the studs if you have the pockets in back of your wheels.  

 

They are 20" rims on your truck, right?

Thanks brother! Yes, the stock 20" All Terrain wheels. I would definitely trim the studs some on a 1" spacer. I did not trim any on mine as I do have the "pockets" in the back of the wheels which I did not know about until I unpacked my cut off wheel. Surprise to me! I did a quick measurement with my pinky finger and had a little left inside the pocket. Very pleased with the poke and stance of the truck after the BORA spacer. HIGHLY recommend these to anybody in the market. I'll get a picture of the poke when it's not snowing here... Thursday is suppose to be 75° here in wonderful Chicagoland. 

IMG_20180407_104546.jpg

IMG_20180407_104556.jpg

Edited by MHardiman90
WT432 New Member

WT432

Posted
Posted (edited)

I have a 2015 GMC Sierra 1500 Z71 4x4 Crew Cab all stock with 265/65 -18 inch Wheels/rims. I was wanting to raise or level out the truck, but still want a slight rake for payload. I don't want the front higher if i put anything in my bed. I have read many forums comparing the 2 inch RC in the front vs the 2.5 inch level RC changing the front and rear. The only discussions i have seen involve non z71 trucks.  For those who have a z71 truck which one do you prefer?

 

My plan was just to do the basic RC 2 inch level in the front and go with 285/65-18 tires, but would hate for the nose to be too high. Should I stick with my plan or go to the 2.5" or find a 1.5" level in the front. Thank you

Edited by WT432

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,962
    Total Members
    8,960
    Most Online
    contrabombarde
    Newest Member
    contrabombarde
    Joined

  • Who's Online   0 Members, 0 Anonymous, 781 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks for all the help so far!   I did try right from 2026 right down to 2021, and only from 2023 down lets me select the option for tire psi change, but I get the vehicle not supported error!   I'll definitely try it under Chevrolet after work today, and I'll get the sensor number from gm for my truck tire sensors. And I'll let you know if it works for me under Chevrolet!   And if that doesn't work, I'm going to guess that what @Atlas said about maybe I have a different body control module could be true!  
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      From where I'm sitting this sounds like a compatibility problem. I'm assuming the 2007 was a 900-series truck, and not an 800-series (they were sold side-by-side in dealerships that model year), since it starts and runs.   This is why I HATE post-2006 vehicles. Everything becomes a huge problem when you try to keep the thing running for longer than the manufacturer has designed it to.    I can't remember when Global-A architecture started - either '10 or '11. For your sake, you had better hope it's '11, or you're going to be spending some BIG money to correct this cluster-eff. That's something you need to find out before doing anything else. You may have several computers bricked ... but the fact that it runs tells me you MIGHT be ok here.     EDIT: Just did a quick refresher. You're screwed. This is Global-A. The 2 systems are NOT compatible in the slightest. Once you get the correct engine in there that IS compatible, you're going to need to see how many computers are locked. Absolute NIGHTMARE to straighten out, too. Your buddy might be better off cutting his losses and finding something else.   Welcome to post-2006 vehicle electronics. This is why I quit the industry, and drive nothing built after 1994. This stuff takes all the fun out of wrenching!  
    • bwiese
      Show Us Your 2019 & Up T1 Pictures !

      By bwiese · Posted

      Recently acquired new 2026 Silv. 1500 WT  - L3B + 4WD,  std cab + std bed, in (duh!) Sierra White. Upgrades: replaced 'steelies' w/  Vision "Flow" black alloys,  17x8.5"; HDX nerf bar w/steps (black powdercoat); Weatherguard large/deep alloy saddle toolbox; Michelin fitted bedmat (sale, perfect fit) Weathertech door sill guards TBD: rear wheebox liners 4x black fender arch trim - searching for best  (Putco: chrome only; not looking for flares either!) -Bill    
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      True, hard to say what differences there may or may not be between Chev and GM as well as a production year or mid year part change either.    I just found it odd that under the Sierra choice on the Autel that many of the last few years of production year did not include the choice of changing the tire pressure but if that is an Autel thing or a GM thing as to why the choices were not there. Knowing what tpms sensors are on the truck should give some guidance into which choices on the tool even make sense to try as I wouldn't give up just yet with the tool but I guess he will see what if anything he comes up with if he finds out a bit more info and tries a few more things on the Autel. 
    • davester
      Needing this part.

      By davester · Posted

      I'm sure if you went to a junkyard where you go in and pull the part off the truck yourself, not a used part place where they do it for you, you can get that part on it's own.  Depending on if and what else you would be buying, and time of day, they might even just skip over adding it as a item to the bill.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...