Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

highspeedZ71 Enthusiast

highspeedZ71

Posted
Posted

Just put on last weekend a Rough country 2” front level and some 20x9 0 275/55/20 e8b4473d7db557f33eb4c0b1256c16c0.heic3fcb23d27d7221ebb528d1500ad21db0.heic

 

 

Sent from my iPhone using Tapatalk

 

  • Like 1
  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

Arkangel Enthusiast

Arkangel

Posted
Posted (edited)

Rough country 2.5 front only, Readylift UCA’s. Gotta measure on level ground but I think im only about 3/8” of rake now, may throw in the rear block

 

x9zqfSv.jpg

255Biwf.jpg

 

Edited by Arkangel
Tyy1907 Enthusiast

Tyy1907

Posted
Posted
3 minutes ago, Arkangel said:

Rough country 2.5 front only, Readylift UCA’s. Gotta measure on level ground but I think im only about 3/8” of rake now, may throw in the rear block

 

x9zqfSv.jpg

255Biwf.jpg

 

Your CV boots aren't contacting your lower control arm?

Arkangel Enthusiast

Arkangel

Posted
Posted (edited)
6 minutes ago, Tyy1907 said:

Your CV boots aren't contacting your lower control arm?

 

Im not sure, should I be concerned? Maybe the angle of the pic or maybe because its at a slope up the driveway? Ill recheck it tomorrow when its light out again

Edited by Arkangel
TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted
Your CV boots aren't contacting your lower control arm?


Yes they are, they’re after market UCA’s specifically designed for that lift.


Sent from my iPhone using Tapatalk
TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted

Rough country 2.5 front only, Readylift UCA’s. Gotta measure on level ground but I think im only about 3/8” of rake now, may throw in the rear block

 

x9zqfSv.jpg

255Biwf.jpg

 



Looks great, your UCA’s look great too compared to stock.


Sent from my iPhone using Tapatalk
Arkangel Enthusiast

Arkangel

Posted
Posted
1 minute ago, TXGREEK said:

 


Looks great, your UCA’s look great too compared to stock.


Sent from my iPhone using Tapatalk

 

Another member mentioned that my CV boots appear to be contacting the LCA, should I be concerned? 

TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted


Looks great, your UCA’s look great too compared to stock.


Sent from my iPhone using Tapatalk

Btw, get rid of those crappy Chinese rancho knock offs and put on some Bilstein 5100’s unless you off-road a lot instead Fox coil over Shocks.


Sent from my iPhone using Tapatalk
TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted
Another member mentioned that my CV boots appear to be contacting the LCA, should I be concerned? 


You do not want that CV rubber boot to touch anything cause it spins while in use. Better get that checked out immediately!!


Sent from my iPhone using Tapatalk
Arkangel Enthusiast

Arkangel

Posted
Posted (edited)
9 minutes ago, TXGREEK said:

 


You do not want that CV rubber boot to touch anything cause it spins while in use. Better get that checked out immediately!!


Sent from my iPhone using Tapatalk

 

Damn! I just had this put on this afternoon! Shouldnt the shop have seen that?? 2.5” too high maybe? Just went out and took another couple shots with the flash its damn close

 

aUNh6Ky.jpg

u8QiqmZ.jpg

Edited by Arkangel
TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted


You do not want that CV rubber boot to touch anything cause it spins while in use. Better get that checked out immediately!!


Sent from my iPhone using Tapatalk


Are those pics with the truck jacked up in the air or sitting on the tires??


Sent from my iPhone using Tapatalk
Arkangel Enthusiast

Arkangel

Posted
Posted (edited)
4 minutes ago, TXGREEK said:

 


Are those pics with the truck jacked up in the air or sitting on the tires??


Sent from my iPhone using Tapatalk

 

Parked the driveway at an incline, not flat

Edited by Arkangel
TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted
Parked the driveway at an incline, not flat

Sorry buddy, those rubber booties shouldn’t be touching anything but air. Looks like a spacer may be left out somewhere. What’s your Leveling setup?

Mine is a 2.25” level, two spacers up front, one top of strut and one sitting bottom of strut. I don’t see and spacers under your strut at all. Please take it in immediately making sure you do not use 4X4 until it’s raised OFF from the lower control arm


Sent from my iPhone using Tapatalk
Arkangel Enthusiast

Arkangel

Posted
Posted (edited)
4 minutes ago, TXGREEK said:


Sorry buddy, those rubber booties shouldn’t be touching anything but air. Looks like a spacer may be left out somewhere. What’s your Leveling setup?

Mine is a 2.25” level, two spacers up front, one top of strut and one sitting bottom of strut. I don’t see and spacers under your strut at all. Please take it in immediately making sure you do not use 4X4 until it’s raised OFF from the lower control arm


Sent from my iPhone using Tapatalk

I have a spacer on the top of the strut and one under the strut, if you zoom in to the pic you can see the black Rough Country spacer under the strut, 2.5” kit

Edited by Arkangel
TXGREEK Senior Enthusiast

TXGREEK

Posted
Posted

Ok, your last pics don’t show it really touching. Close but not touching. Those rubber booties turn as you’re using 4X4 so you do not want them touching. The pics may be an illusion, if you can put your finger between the two then you should be good just do not want them touching.


Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      The Peckish Synapse

      By diyer2 · Posted

      She's laughing all the way to the bank.
    • newdude
      SLE 2.7L L4 shudders @ 2000-3000RPM

      By newdude · Posted

      There's a new PI on 2023-2026 L3B shudder.  Possible faulty front oxygen sensor.   Dealer can pull up PIP6060A and give it a read.  
    • newdude
      OBD not ready?

      By newdude · Posted

      Also here's the drive cycle for a 2021 Yukon with V8.  DO NOT USE THE CRUISE CONTROL WHEN RUNNING DRIVE CYCLE!!!!!:   Warning: Road test a vehicle under safe conditions and while obeying all traffic laws. Do not attempt any maneuvers that could jeopardize vehicle control. Failure to adhere to these precautions could lead to serious personal injury and vehicle damage. Note: You have completed this procedure when all parameters display Complete. Short stops for traffic will not affect the procedure. Note: Do NOT use cruise control during this procedure. Ignition/Vehicle » Off — For greater than 8 h Verify the scan tool parameter: Cold Start-Up = Yes If not the specified state Ignition/Vehicle » Off — For greater than 8 h & Repeat this step If the specified state Ignition » On / Vehicle » In Service Mode — For 1 min Engine » Idling — For 2 min Drive the vehicle while maintaining the following conditions for 20 min: Part Throttle Vehicle Speed = 24 to 97 km/h (15 to 60 MPH) Safely stop the vehicle Operate the engine/vehicle within the following conditions: Accelerate the vehicle to 64 km/h (40 MPH) Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 10% and 13% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 13% and 16% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 16% and 19% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 19% and 22% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 22% and 25% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Maintain steady state throttle at 89 km/h (55 MPH) — For 10 min Safely stop the vehicle
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      About the only GM that compares well with its competitors through the small to midsize vehicles is the Trax. I would like nothing better to just drive GMs. My wife in a Cadillac me in a Chevy minivan and Colorado. Part of my day is comprised of reading and watching comparisons of automobile. I could buy a car today. I’m back to research the next. 
    • newdude
      OBD not ready?

      By newdude · Posted

      Do you have any DFM defeat devices like the Range modules?  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...