Jump to content

Center console swap?

quickvert1

By quickvert1
in Modifications & Accessories

 Share

Recommended Posts

16GMCSS Enthusiast

16GMCSS

Posted
Posted

All depends on what trim you want. For example I have the grand lace trim in my doors so I got the grand lace trim in the console.

I also have a 2015 and the part numbers I used were. f5333a0504e141e4d25193b9166e7967.jpg

Sent from my iPhone using Tapatalk

I am interested in doing this as well. Quick question though. On the list of parts you have I am not seeing the armrest/lid. Did that come with the console?

  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkfox1
darkfox1

OK.. mine's in.   Here's a writeup, cos I haven't seen one so far.   1. remove the "ash tray" and cig. ligther in your dash with 3 t-10 torx screws, and 2 clips. 2. Remove the radio trim, clips i

dla
dla

I always wanted a RCSB with buckets and a center console...   Received and installed mine yesterday. Very straight forward, thanks for all who posted instructions and part numbers.   Possibly to h

o7bodybagged
o7bodybagged

Finally the console is complete now ready for the install and see what other problems I run into

Posted Images

16GMCSS Enthusiast

16GMCSS

Posted
Posted

^it comes with the console.

 

 

Yes, it comes with the console

 

 

Sent from my iPhone using Tapatalk

 

Thank you both!!

harveyfamily Enthusiast

harveyfamily

Posted
Posted

Installed my console last weekend.I powered up my front usb ports instead of the ones inside the console since they are easier to access when you're driving.If anyone would like to do it this way it's really easy.Remove the entire harness from the jump seat and you will have the right plugs on that harness to plug right into the front usb's(plug and play)they charge and play music. .there is plenty of length to reach without cutting.then just splice the new console harness in to power up the 12v outlets and light in the console(I spliced everything in just because I was already into it and I want as much to work as possible.On mine all colors matched with the exception of the 12v+ but those are obvious since they just go to the 12v power ports.The white wire that doesn't match anything is for the light in the console,just connect to the 12v source of your choice .I expect that with the addition of the usb cable others have mentioned the usb ports inside the console could be used for charging if it was important to you.

Sorry for the long post.Hope someone can use it.

 

So if I followed your instructions and wanted the inside USB ports to be able to charge would I just need the additional USB cable going to the module behind the glove box?

harveyfamily Enthusiast

harveyfamily

Posted
Posted

Ordered the parts identical as the list above for $587 which included shipping. My dealer couldn't even come close.

 

Excited!!

 

 

Sent from my iPhone using Tapatalk

Aldila Enthusiast

Aldila

Posted
Posted

Anyone have the part numbers to accommodate a 2016 Z71? I did the swap on a 2014 Z71, but managed to order incorrect trim. I hope to avoid that this time.

1911-A1 Enthusiast

1911-A1

Posted
Posted

 

So if I followed your instructions and wanted the inside USB ports to be able to charge would I just need the additional USB cable going to the module behind the glove box?

I can't guarantee it but it makes sense since it should be the same as others have done for the front ports.Again I didn't try it since I am happy with mine the way they are for now.maybe others could confirm this for you.

Deanjo Enthusiast

Deanjo

Posted
Posted (edited)

Question.... is this trim style what they call reverse tartan?

 

IMG_2833.jpg

 

If it is please correct me if I'm wrong but for my 2014 silverado I would need the following parts to replace the jump seat with a console.

 

22995069

22817347

23467516

23467112

22776807

Edited by Deanjo
harveyfamily Enthusiast

harveyfamily

Posted
Posted

Quick shipping from GM Parts Headquarters as I got the notification that it shipped out today after ordering Friday evening.

 

I've looked through this thread and I'm sure someone has posted this and I missed it, but does someone know the jumpseat removal/center console install procedure? Do I need to get any additional bolts for this or will I have them already from the jump seat?

harveyfamily Enthusiast

harveyfamily

Posted
Posted

Installed my console yesterday. Everything went well. I don't have the three USB's up front working yet, but feel like I'm very close. I have successfully attached the USB cable from the HMI (behind the glove box) to the center console. On my 2015, I have the extra USB in the upper glove box. I disconnected it from the HMI (it's the USB with the green plug) and plugged in the new cable in its place. I used the cable recommended by TBarn (GM part 19303328.) You have to trim the connector on that cable quite a bit to make it fit in the HMI. If you are patient, it can be done and will still securely connect to the HMI. I then routed the cable to the center console.

 

I ran into a problem trying to get power to pins 4 and 6 on the USB. My local dealership didn't have any connectors (SAIT-A03GF-M064) in tray 27. I rummaged around and found something very similar from an old PC power supply that I was going to try and use, but they weren't a secure fit - too loose.

 

The way I installed the console was to remove the "new" console wiring harness, except for the wiring to the back cigarette lighter and the switch leg wiring for the light. I left that wiring in place, but cut out the remainder of the harness, leaving plenty of wire to splice. I then took the harness out of the "old" flip console. I spliced that old harness to the back cigarette lighter and the light circuit. Everything else on the back of the console is plug and play. I then used one of the cigarette plugs from the new harness to build a jumper for the second cigarette plug up front. Everything now works except for the power to the three USBs.

 

I woke up this morning and realized I think I have what I need to finish this. Because I pulled out most of the new console harness, I'm left with the plug from the 2 USB/SD/stereo plug. That plug is identical to the plug that connects on the back of the 3 USBs. So my next step is to cut that plug with plenty of excess wire and splice pins 4 and 6 to power and ground. My theory is that I will have fully functioning USBs up front once I do this. (The only minor downside is losing the USB in the upper glove box.)

 

I plan to give this a try one night this week. I'll report back.

Is it possible to connect the USB cable from the inside of the console in the jump seat to the 3 USBs in the front of the console and have it charge/play, then get this cable (GM #19303328) and connect it to the inside USB ports in the new console and have them charge?

JorgeGomez4462 Enthusiast

JorgeGomez4462

Posted
Posted (edited)

So I have a 2015 Silverado 1500 LTZ. And I have a Jump Seat in it. I was wondering what parts I needed to do the swap? I have the Black Leather Interior, Greyish door panels and Greyish panels next to my 8" MyLink Radio on the dash. Any part numbers that would fit this one with my Black Leather Interior? I'm looking for a Black Center Console, not the Brownish with Wood on it. Thanks in advance!

Edited by JorgeGomez4462
Aldila Enthusiast

Aldila

Posted
Posted

Question.... is this trim style what they call reverse tartan?

 

IMG_2833.jpg

 

If it is please correct me if I'm wrong but for my 2014 silverado I would need the following parts to replace the jump seat with a console.

 

22995069

22817347

23467516

23467112

22776807

Is that silver? I think I have the same and trying to figure out part number.

post-136723-0-83292100-1461615568_thumb.jpg

post-136723-0-83292100-1461615568_thumb.jpg

post-136723-0-83292100-1461615568_thumb.jpg

post-136723-0-83292100-1461615568_thumb.jpg

Deanjo Enthusiast

Deanjo

Posted
Posted

Is that silver? I think I have the same and trying to figure out part number.

 

Ya it is "silver". Hard to tell if it the same with your picture as it is hard to see the texture detail.

  • Like 1
Aldila Enthusiast

Aldila

Posted
Posted

Ya it is "silver". Hard to tell if it the same with your picture as it is hard to see the texture detail.

Yeah, I was told to order synthesis before, but it didn't have the scale looking design. It was just silver. Mine has the scale looking design.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,914
    Total Members
    8,960
    Most Online
    AidenVorpagel
    Newest Member
    AidenVorpagel
    Joined

  • Who's Online   3 Members, 0 Anonymous, 1,286 Guests (See full list)

  • Latest Articles

  • Posts

    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • davester
      cam upgrade in CA

      By davester · Posted

      apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
    • davester
      Possible lifter tick after DOD delete

      By davester · Posted

      yes, leaking exhaust will mess up o2 sensor readings, which in turn messes up fuel trims.
    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      286,740 Mile Services   8/6/2026   New AC Compressor. Refrigerant oil and dye, evacuate and charge system.  New exhaust system from cat back.  New Iridium plugs plus replace #3 coil Repair/rewire headlamp wiring (passenger side) and replace all forward bulbs. Polish lenses of both assemblies.  Pull rear rotors, clean and adjust parking assembly. Inspect, clean and grease front calipers. Check pads and shoes.  4 wheel power bleed of brake system. Dot 4 Reset idle speed 50 rpm higher New Serpentine belt.    Will need new pads in the rear in about 5K more miles.    Tax Title and License out the door just short of a grand.    AC clutch had bitten the dust. 1 year warranty on the pick and save replacement. Thing will make a Polar Bear cry Uncle.  He spent quite some time on the wiring. It was in the harness and he does nothing half. I got off cheap. I have considerable more light down the road. Sylvania Silver Star replacements.  Gas seal between the porcelain and shell of plug #3 was blown, cooked the coil. That was the cold miss.  Love the new exhaust. I can sneak into the neighborhood again.  Nice to have a working parking brake again. Belle Tire never got it done. That was disappointing.    This was one of her bigger bills and still way cheaper than a payment even given the oil consumption. This thing cost me under a hundred a month in repairs and normal routine costs. What is my incentive to replace it? 🤔           
    • AidenVorpagel
      cam upgrade in CA

      By AidenVorpagel · Posted

      hello I recently bought a 2012 gmc 1500 with a 5.3 and have a AFM disabler on it I'm interested in doing a cam but I'm worried if I remove the AFM system I will fail smog does anyone have info if they are able to detect that or a work around to it (not talking about hot smogging) please let me know thank you  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...