Jump to content

Recommended Posts

Posted

I have this too, it sounds like a valve tick from my old LS1 days -- It's pretty loud. i can mainly hear it at idle -- when I stop to get the mail and i get out of the truck every day, it's louder than my Borla XR1 muffler w/ deleted resonator......yet it doesn't throw any codes, and the dealership told me its the injectors, and it's "normal" in these engines.....i've had people walk up asking what's wrong with the truck...so that's fun.

  • 2 weeks later...
Posted

Anyone with updates? V4 noise due to vacuum issue? Manifold gasket? exhaust flange? lifter noise?

  • 1 month later...
Posted

I am currently going through the same problem since 9k miles now at 18k. Ticking noise while under load at low rpms. Had it in the shop 3 times so far goes back this Monday for round 4. 1st time they said couldn't replicate, 2nd time blamed K&N cai 3rd time I removed cai and they finally heard the noise and said it's not normal. Tech intially thought exhaust leak but none found.They called GM engineer who suggested vacuum pump replacement. Still ticking. I feel like it's the coming from catalytic converter, maybe internal crack? Let's see what they do next.

 

Sent from my SM-G930V using Tapatalk

Posted

I've had a 14, 15, and now a 16 and they've all ticked under light load, most noticeable on the highway. Sounds like it's coming from the driver side manifold. I've unfortunately accepted it as "normal".

Posted

I've had a 14, 15, and now a 16 and they've all ticked under light load, most noticeable on the highway. Sounds like it's coming from the driver side manifold. I've unfortunately accepted it as "normal".

same here. Ive had it looked at a bunch of times. The dealer hears it but has no explanation

Posted

same here. Ive had it looked at a bunch of times. The dealer hears it but has no explanation

 

Yep, I've just accepted it too. Put an intake and exhaust on and it's not as noticeable due to other noises lol

  • 2 months later...
Posted

Ticking issue finally resolved. Cracked manifold on drivers side replaced, new fuel feed pipe, and new steering shaft boot. Truck sounds great. post-170761-0-46551800-1499306373_thumb.jpg

post-170761-0-46551800-1499306373_thumb.jpg

post-170761-0-46551800-1499306373_thumb.jpg

post-170761-0-46551800-1499306373_thumb.jpg

  • Like 2
Posted

My 2016 Silverado began ticking under acceleration last November (truck bought new in July 2016). At first it only appeared after the vehicle had been driven for a while (20+ kms) and it wasn't very noticable unless you knew what to look for (I'm observant to an unhealthy level, just ask my wife!). Sounded like it was coming from driver side area around the parking brake lever. Put studded tires on for the ice in the winter and I guess that droned out the noise for the most part until I put my summer tires back on in April. The ticking has gotten MUCH worse, and seems to be getting worse with every passing day. Now it starts almost immediately after starting the truck, and sometimes it begins even faster if I happen to hit a good bump in the road. Once it starts it does not stop until the truck has been parked for a while and cools down. Today I noticed that I can replicate the sound (albeit much lower volume) when the truck is in neutral and the engine is revved (this is something new). Not nearly as loud as when in drive, but still there.

I'm glad to see it isn't only me having this trouble. I have an appointment set up for July 19th to get it checked out. I intend to show them the post that Rick62783 posted above me. Thanks for all of the information, and I will keep everyone updated as to the result of the visit.

Posted

Ticking issue finally resolved. Cracked manifold on drivers side replaced, new fuel feed pipe, and new steering shaft boot. Truck sounds great. attachicon.gif20170705_215915.jpg

 

How many more cases are like this? I feel you're onto something that the rest of our dealers don't want to deal with

Posted

I've been a longtime lurker on this thread and just now posting as I have had this similar issue since about 4k miles in my '16 GMC Sierra SLT 5.3L that I bought in June '16. Had the dealer look into a "possible exhaust leak on the driver's side" when I brought it in for the first oil change at around 6k miles and they claimed it as a normal fuel pump noise. My truck is at ~22k miles now and the issue has not gotten any better or worse since I first noticed it. Following this thread to hopefully find a permanent solution!

Posted

 

From the
TechLink pages:
... may produce some unfamiliar sounds during cold starts as well as during warm operation...

 

Don't you just love these kinds of disclaimer!? Basically, it can happen all the time, anytime. I hear it on mine randomly. It's just quite annoying.

Posted

Ticking issue finally resolved. Cracked manifold on drivers side replaced, new fuel feed pipe, and new steering shaft boot. Truck sounds great. attachicon.gif20170705_215915.jpg

 

The last time I took my truck in for service and they did a test on it. The service manager noticed the noise too but they said it was normal - fuel injector noise. So they dismissed it. I am guessing each dealership works differently.

 

How many more cases are like this? I feel you're onto something that the rest of our dealers don't want to deal with

agreed.

Posted

Mine only makes the noise when the truck is at operating temperature. The higher the RPM the louder and faster the tick.

Posted

I don't notice the noise in mine during a normal idle, and typically not when I rev it up in park. The noise comes from the driver's side floorboard and sounds very similar to an exhaust leak mostly in lower RPM's while moving, both in V4 and V8 as well with A/C on and off. The noise is not present 100% of the time, but it is present both in town and on the highway as well towing/not towing. I have another oil change due in ~2k miles, and I would typically perform these myself as I already used the two freebies from the dealer, but I would be open to dropping my truck off at the dealer if a resolution is found and letting them perform my next oil change while they're under the hood

Posted

@GM Customer Service please send me a PM, your inbox appears to be full

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • That should answer the maximum depth difference between the stock and the PPE so its not hugely lower. As to the PML pan, they don't make any claims that it fits the L8T with the same transmission and in fact leave their information confusing, however on the surface it says "for Duramax" and so its hard to say. I know a while back and not sure which brand it was that specifically stated that the extra capacity pan that particular company made did NOT fit the gas version. 
    • There are several versions of the 5100's. Some for stock height, some for leveled, some for lifted.    Side note. I finally had a chance to tow with my 30' gooseneck with about 10,000 lbs of material on it this past week. Hands down the 5100's made the trailer towing much more stable and comfortable. I even had 10 cmu blocks in the bed. What a difference over the stock shocks. 
    • According to PML, the stock pan is 4.3" deep - (PML info): Dimensions: at deepest area, PML pan is 7 inches, stock pan is 4.3 inches    PPE is 5.4" so roughly 1.1" deeper than stock
    • I had not realized that PPE has come out with a version of a cast aluminum oil pan specific to being able to fit onto the 10L1000 with the L8T engine sometime this spring. I was doubting that anyone would come out with something beyond what Dorman had in more of a direct factory pan swap. I see from one comment that is on the PPE site that they found the pan to be tighter to install then the factory unit and having to flex the exhaust down to fit it. I didn't lookup any specs if they have any as per how much lower it hangs but as it holds more oil and has fins outside the pan it would no doubt hang a certain amount lower.    I looked back at the site and they do have some depth measurements to get a rough comparison to the factory pan total height or hang down if you will at the front and rear of the pan so that will give a good idea how much further down this pan would end up being for ground clearance issues.    2024-2026 GM 6.6L Gas 10L1000 Heavy-Duty Cast Transmission Pan – Pacific Performance Engineering    
    • I'm in constant amazement over the number of people that do oil maintenance by how they feel, what they were told, what materials cost, what brand A claims vs brand B.     Come to think of it, this behavior isn't exclusive to oil. 🤔 They drive this way too. 😬   There is a 20 plus page thread on BITOG on Mobil 1 Advanced Clean vs Valvoline Restore and Protect it would be amusing if it were not so........humanly pitiful.   Last Sunday we were are sitting at services and listening to a speaker talk about Jesus parable of the wide and narrow gates and he said something that hadn't dawned on me but totally fit the way people in general are about just about everything. He said there are so few people on the narrow path leading to a good reward not because the the narrow gate was hidden or hard to find but because the wide gate leading to a bad end it so darn easy and uncomplicated to follow!!!             
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...