Jump to content

Recommended Posts

Posted (edited)

did you stage that pic by putting dirt on that filter? haha that is disgusting

Nope! I was surprised with the fuzz that was piled up in that corner. I clearly need to do this every 10k miles (or less), instead of every 15-17k.

 

When I pulled out the filter, a leaf fell off the back of the filter and down into the blower motor. I didn't realize it until I fired the fan up full blast and it started making a buzzing sound. Had to pull the new filter back out, and wedge my hand in there and pull it out. I was lucky I didn't have to take the blower motor out just to get it.

Edited by 2015_Sierra
Posted

 

Haha, yeah I reread some of the posts here, and my idea of how leaves get into and on the cabin air filter was quite wrong. I pictured a vehicle sitting outside somehow being more prone to crap falling in,, but that isn't how that works lol.

Its all good, just playin.

Posted

So I took a video scope under the window under the hood of my truck and found that there is absolutely nothing to prevent a mouse from getting inside and into the filter which they can easily eat through. So within the next week I'm going to dismantle and fix a screen to prevent it any mice or large leaves from getting into the cabin. I'll take some pictures and videos and post them

Posted

Will you be able to clean that screen off that you are going to put in?

Posted

So I took a video scope under the window under the hood of my truck and found that there is absolutely nothing to prevent a mouse from getting inside and into the filter which they can easily eat through. So within the next week I'm going to dismantle and fix a screen to prevent it any mice or large leaves from getting into the cabin. I'll take some pictures and videos and post them

 

Looking forward to see what you come up with.

Posted

Will you be able to clean that screen off that you are going to put in?

That's probably the only part I am concerned about. I have an IPA Air Comb which is like a long blow gun with sideways air pressure which i should be able to get in there and place enough pressure to dislodge any leaves etc. Ultimately, if i had too i'll hard plumb an air hose with a quick disconnect...that i can hook onto periodically. Anything would be better than the alternative....

  • 1 month later...
Posted

Nope! I was surprised with the fuzz that was piled up in that corner. I clearly need to do this every 10k miles (or less), instead of every 15-17k.

 

When I pulled out the filter, a leaf fell off the back of the filter and down into the blower motor. I didn't realize it until I fired the fan up full blast and it started making a buzzing sound. Had to pull the new filter back out, and wedge my hand in there and pull it out. I was lucky I didn't have to take the blower motor out just to get it.

After reading these posts I decided to check mine truck seeing as we spent last summer in CT where the truck was parked outside. Sure as hell, the filter was full of crap along with a mice nest and about a 1000 mice turds...nice to know I had been breathing this for a couple of months

......that little ball of lint you found is a mouse nest....

  • Like 1
Posted

After reading these posts I decided to check mine truck seeing as we spent last summer in CT where the truck was parked outside. Sure as hell, the filter was full of crap along with a mice nest and about a 1000 mice turds...nice to know I had been breathing this for a couple of months

......that little ball of lint you found is a mouse nest....

Thanks for the heads up. Guess I'll be checking this WAY more often.

Posted

its amazing how quickly those filters can dirty up. It is probably not a bad idea if you folks make a habit of checking the filter every 6 months or so for optimum HVAC performance, no matter what type of climate you live in, perhaps??? eh??

Posted (edited)

Go to an outdoor, hunting or farm supply store. Buy a $4 little bottle of coyote urine. Put a few drops here and there under the hood. I hit the wire looms a bit as well. Do Not put it on the air filter or anywhere in the air ducts or you will have to get used to coyote urine. I apply it about twice a year, it keeps the mice away.

 

The K&N Durable cabin filter is a great investment. It takes about ten minutes to install it the first time. Once you have cleaned it a time or two, you can get it out in two minutes flat.

Edited by Darksky
  • Like 1
Posted

Another trick I have read is to use scented dryer sheets under the hood. They can be zip tied in place and rats/mice despise the smell and won't get near. I'm lucky my cabin filter did not look anywhere near as bad as some I have seen on this forum when I changed it.

Posted

Another trick I have read is to use scented dryer sheets under the hood. They can be zip tied in place and rats/mice despise the smell and won't get near. I'm lucky my cabin filter did not look anywhere near as bad as some I have seen on this forum when I changed it.

I know someone that used the dryer sheets in his MH. The mice used them to make a nest :)

Posted

So I took a video scope under the window under the hood of my truck and found that there is absolutely nothing to prevent a mouse from getting inside and into the filter which they can easily eat through. So within the next week I'm going to dismantle and fix a screen to prevent it any mice or large leaves from getting into the cabin. I'll take some pictures and videos and post them

 

Wallmart sells stainless steel scrubby pads (for pots'n pan's). When I put my motorsickle away for the winter (shed behind the house) I shoved Wallyworld stainless steel pads into the exhaust pipes to keep the mice out. Same stuff might work under the hood of our trucks??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • On 2021 3500hd it consistently sets automatically when selecting park if the incline/decline is above a certain angle. 
    • Curious, did anyone ever get a fix for the vibration reported here.   I have a 2024 Silverado with 6.6 duramax.   I’m noting the same vibration resonating up through the steering shaft into the steering wheel.    Best way to describe- like someone is tapping on the steering shaft/components and it’s resonating into the steering wheel.    thanks. 
    • Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • 2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...