Jump to content

4l60e problem

Roy450

Recommended Posts

Roy450 New Member

Roy450

Posted
Posted

Hello, I have a 2003 silverado 1500 4x4 4.8L with a reman 4l60e that has approx. 11,000 miles on it. The problem i am having started after the trans had 9k on it. After the truck has been driven if it is shut off or idled for a few minutes it will not accelerate or shift normally. The trans is not slipping, the rpms just increase very slowly. It shifts at high rpms and usually very suddenly unles you let off on the gas to shift. This happens through all gears and it will completely go away and shift normally after a few minutes of driving. Also, if has been idling for a few minutes the rpms will go down to abt 450-500 then jump back to abt 650 and the truck will have a shudder as though it is trying to give power to something while just sitting there. It does not make any difference if it is in gear or park. This has never happened taking off with the trans cold and it has no problems with stop and go traffic only after idling or being shut off. It occasionally has a clunk while this is happening. Any suggestions would be greatly appreciated. Thanks

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Joke Thread

      By Grumpy Bear · Posted

    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      You're better read than that Atlas. 😏   British science fiction writer Arthur C. Clarke formulated three adages that are known as Clarke's three laws, of which the third law – that "any sufficiently advanced technology is indistinguishable from magic" – is the best known and most widely cited.   Stribeck and the pivotable Hersey Number isn't voodoo nor snake oil. That part is physics. It's what marketing and bean counters do with it that is snake oil and voodoo.    Stribeck is the relationship between Hersey and the Coefficient of Friction. Within the Hersey Equation if viscosity and viscosity is 'Dependent' on.......heat.......and.......viscosity index or the temperature to viscosity slope.    Specifically Hersey is the viscosity AT THE TEMPERATURE IN THAT LOCATION FOR THAT SLOPE.   Hydrodynamic lubrication exist when the film thickness in the location is 3X the Ra roughness of the surface. This is irrespective of the hardness of the substrate. To obtain that thickness X viscosity is required for Y velocity at Z load. That's a lot of moving parts. It is also impossible to maintain in an ICE but nearly possible with a turbine under constant load.    What does that mean? Error heavy and operate light. Wear is inevitable but the rate of wear and the milage obtainable are a function of prevailing conditions and HABITS. The only penalty is viscous drag and at fractions so low as to be well worth the effort. Double the life, half the manufacturing carbon foot print. Greed is the only impediment.    The materials generated by SwRI are the RESULT not an estimation or a hypothesis.    Don't delude yourself sir, EV's have as many pitfalls as ICE's. We just don't know what they are yet and it will take longer to sort as MARKETING and GREEDY CEO's have had more time to polish the turd they are selling. 
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      You can always count on greed to prey on ignorance and stupidity.    Friend bought a 2019 Ford Flex and asked me about using Valvoline R&P 5W30 in it. Told him give the miles on it and the fact it wasn't yet using oil that it was a good plan. He uses a Valvoline quick change shop for his oil service.   First they tell him that isn't the oil the OEM recommends. He told them he didn't care what the OEM thought. Then they floated the, "But it will void your warranty"    His reply was it's a 2019, there is no warranty and informed them their knowledge of the law was lacking.    Then they tell him 'But it will ruin your motor"!.    Mine to ruin he says. Finally they give in and charge him 150% the semi-syn price    Point it the brainwash is so embedded that even the service industry is drunk on their swill. The public is right behind them. Echoing the same lies on every forum and media platform. If the end goal is indeed EV then I'd say that ship is about built. 
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Diesel hit $6.00 here today at the truck stop.   Payed $2.79 for E85 today too.
    • richard wysong
      Electrical Problem - solved

      By richard wysong · Posted

      Thanks for posting, I'm sure it will help someone

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...