Jump to content

Recommended Posts

Posted

After thinking about it, its probably not a true "short".

That whole circuit is basically a giant resistor (as that is what creates the heat to defrost the glass)

So I'm assuming it is pulling a descent amount of current. I bet the true issue is a poor connection in that black box that is causing high resistance. When you are pushing current, you don't want resistance as that in itself will heat up and start to scorch the contacts.

I'd bet money that is what everyone smells before hand. 

Contacts in the black box have too high of resistance and start to scorch, heat up and smoke and that high heat concentrated in that box on the glass is what shatters the glass.

I bet if you held a small torch on the corner of the glass, it would do the exact same thing. 

  • Like 1
Posted

I wish I would have seen this yesterday... :(

 

Just found this after getting a call from my dealer this morning saying they can't find anything so decided to do my own research.

 

Yesterday my wife was driving our 2015 Silverado when she smelled something burning then suddenly heard a loud pop. She thought the truck caught on fire then realized the back drivers side glass had shattered. Of course my first mistake was taking it straight to the dealer.

 

They just called to say they found no evidence of any electrical fire ( I could smell it yesterday when I dropped it off) and can see a point of impact on the glass.( BTW they want $1400 to replace the glass!?!)

 

After reading this I asked them to pull the back seat and check the defroster and wiring etc. (of course for an extra $250). We will see what they come back with. Wish I would have known to contact a GM service Rep first

Posted (edited)
13 minutes ago, nw96 said:

I wish I would have seen this yesterday... :(

 

Just found this after getting a call from my dealer this morning saying they can't find anything so decided to do my own research.

 

Yesterday my wife was driving our 2015 Silverado when she smelled something burning then suddenly heard a loud pop. She thought the truck caught on fire then realized the back drivers side glass had shattered. Of course my first mistake was taking it straight to the dealer.

 

They just called to say they found no evidence of any electrical fire ( I could smell it yesterday when I dropped it off) and can see a point of impact on the glass.( BTW they want $1400 to replace the glass!?!)

 

After reading this I asked them to pull the back seat and check the defroster and wiring etc. (of course for an extra $250). We will see what they come back with. Wish I would have known to contact a GM service Rep first

Wow! Are you paying for that replacement? I thought most insurance will fix it with 0 deductable? Maybe my understanding is incorrect though.

Edited by piratepenguin
Posted
4 minutes ago, piratepenguin said:

Wow! Are you paying for that replacement? I thought most insurance will fix it with 0 deductable? Maybe my understanding is incorrect though.

I have not approved the window replacement yet, waiting to see what they find in regards to the defroster etc. I had not thought about the insurance angle. I may look in to it. Thanks! 

Posted
35 minutes ago, nw96 said:

I wish I would have seen this yesterday... :(

 

Just found this after getting a call from my dealer this morning saying they can't find anything so decided to do my own research.

 

Yesterday my wife was driving our 2015 Silverado when she smelled something burning then suddenly heard a loud pop. She thought the truck caught on fire then realized the back drivers side glass had shattered. Of course my first mistake was taking it straight to the dealer.

 

They just called to say they found no evidence of any electrical fire ( I could smell it yesterday when I dropped it off) and can see a point of impact on the glass.( BTW they want $1400 to replace the glass!?!)

 

After reading this I asked them to pull the back seat and check the defroster and wiring etc. (of course for an extra $250). We will see what they come back with. Wish I would have known to contact a GM service Rep first

I contacted GM directly and they said to see the dealership.  I asked specifically for a GM rep but one was not provided.  The dealership I went to was helpful, but then again, my window didn't shatter.  That could've been a way different ball game.

Posted
56 minutes ago, rah7777777 said:

After thinking about it, its probably not a true "short".

That whole circuit is basically a giant resistor (as that is what creates the heat to defrost the glass)

So I'm assuming it is pulling a descent amount of current. I bet the true issue is a poor connection in that black box that is causing high resistance. When you are pushing current, you don't want resistance as that in itself will heat up and start to scorch the contacts.

I'd bet money that is what everyone smells before hand. 

Contacts in the black box have too high of resistance and start to scorch, heat up and smoke and that high heat concentrated in that box on the glass is what shatters the glass.

I bet if you held a small torch on the corner of the glass, it would do the exact same thing. 

 

 

The black box is closer to the passenger rear window but I am seeing all of the driver side rear windows shatter.

Posted

I wanted to provide an update. The dealer was not willing to help me out after all and I went the insurance route with safelite. Hopefully installation goes good next week.

Posted

Its sad gm gets away with making our insurance pay for it.  Please report to National department of transportation safety, easily done online. The more reports the more serious it gets taken.

U think the insurance companies would  want to investigate but i told mine and they didnt really care. They should sue gm for all the windows they have had to pay to repair, due to GM not helping.

 

Posted

Crazy how it is only the sliding back windows that seem to be affected. Many full back glass windows out there with defroster, yet not hearing any chatter about those exploding. 

 

As @Lee_lee said every one should report it https://www.nhtsa.gov

Posted

I'm surprised to find out that the single glass piece cannot be replaced on the sliding glass models. It is a whole assembled unit being replaced on mine. Need to take the back seats out even to access the motor. Hopefully this will solve all my issues. 

Posted

Finally heard back late Friday, no evidence of smoke or any other damage but found a "point of impact" on the glass. Picking it up tomorrow and will just take it to a glass place myself. Thinking about pulling the seat and looking myself.


Sent from my iPhone using Tapatalk

Posted
3 hours ago, nw96 said:

Finally heard back late Friday, no evidence of smoke or any other damage but found a "point of impact" on the glass. Picking it up tomorrow and will just take it to a glass place myself. Thinking about pulling the seat and looking myself.


Sent from my iPhone using Tapatalk

May be try contacting the EPA. See if they will Levy a fine against them for trying to blow smoke up your butt. 

Posted
May be try contacting the EPA. See if they will Levy a fine against them for trying to blow smoke up your butt. 

[emoji23] good one. My wife is pissed. Feels like they are saying she's lying. I've bought 3 new Chevy trucks from this dealer. She holds a grudge. Don't think we are buying from them again


Sent from my iPhone using Tapatalk
Posted

"Point of impact" is the exact thing they said to me too,  Its BS!  It wont let me upload video(too big). But when paused u can clearly see there was no chip or crack in window whatsoever while it was smoking. 

See my earlier replies for more details and photo of burn damage the glass people found.  What dealership? I hope everyone is using Google reviews on maps for bad dealership experiences, Maybe add link to this forum! Tons of people check google reviews.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,993
    Total Members
    8,960
    Most Online
    President Roberto
    Newest Member
    President Roberto
    Joined
  • Who's Online   1 Member, 0 Anonymous, 270 Guests (See full list)


  • Latest Articles

  • Posts

    • I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Ok, I got the all the codes. What do you all think would be a place to start?
    • How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • 3.39 Kroger’s in Montgomery Texas. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...