Jump to content

Hood Latch Switch Bypass

TenshiWingusu

By TenshiWingusu
in Troubleshooting & Recalls

 Share

Recommended Posts

Linden16 Enthusiast

Linden16

Posted
Posted
33 minutes ago, TenshiWingusu said:

I hear ya. I would check the resistance on the new switch in both positions, you can force the latch closed with a screwdriver then pop it with the interior hood release. If the switch is in the spec mentioned above it's either bad wires somewhere or the control module has issues.

Yeah hey. I wonder if the dealership can silence the alarm that would be perfect as long as theres no ringing id be happy lol

  • 2 weeks later...
  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

TenshiWingusu
TenshiWingusu

I made an account just to post the fix for this, couldn't find it anywhere.... Your mileage may vary but this is what worked for me.   After having my alarm go off continuously with the hood

Travis Dach
Travis Dach

Please Please Please,   Before anyone puts in a resistor to replace the hood switch, look at this first, especially if you are having these symptoms below.      Hood open warning w

Linden16
Linden16

But yeah i want my remote start thats handy lol. Buy a $60000 truck and have no remote start cause of a stupid hood sensor. Ill have to call the dealership and see. But i know theyll just charge you a

Posted Images

Linden16 Enthusiast

Linden16

Posted
Posted
On 2019-02-18 at 11:18 AM, TenshiWingusu said:

I hear ya. I would check the resistance on the new switch in both positions, you can force the latch closed with a screwdriver then pop it with the interior hood release. If the switch is in the spec mentioned above it's either bad wires somewhere or the control module has issues.

Do you think if I unplugged that sensor and got a aftermarket remote start would it work? Or would the aftermarket remote start still need to know that the hood is closed so would have to stay plugged in

  • 1 month later...
nissyota88 New Member

nissyota88

Posted
Posted

Can someone please show me a wiring diagram and pins on bcm. This truck got in a wreck and has a different wiring harness, but came stock with a hood switch with no pigtail

  • 5 months later...
jaytee10 New Member

jaytee10

Posted
Posted
On 4/20/2019 at 1:54 AM, nissyota88 said:

Can someone please show me a wiring diagram and pins on bcm. This truck got in a wreck and has a different wiring harness, but came stock with a hood switch with no pigtail

What model year truck do you have?

  • 2 months later...
Nick1220 New Member

Nick1220

Posted
Posted

I have a 2008 Chevy equinox that the factory remote start stopped working on. No service engine lights. No indication that a door or hood is open. I’ve changed the gas cap and even checked the tire pressure even though no lights indicated such problem. However I’m still having the same issue. The remote start won’t start the vehicle. The key fob locks/ unlocks the vehicle any and every time a button is pushed. Even illuminates the light when attempting to remote start but it’s like the process just stops. I’m lost definitely could use some ideas and can’t afford a garage to fix it. 

  • 1 month later...
ride_z71 New Member

ride_z71

Posted
Posted

One evening my 2018 stock alarm went off...I thought I must have hit the panick button on my remote...

The next morning I could not remote start the truck...

I get in, start it, and my hood open message was on with my check engine light...I checked the hood several times and it was opening and closing as it should...

Searched and found this post, measured the resistance between the black and red wire on the hood sensor connector and it read 529 ohms ope or closed.

Replaced the hood sensor and it fixed the open hood message and then I had to clear the code...

 

Tempatures were in the 20's to 30's and I had 51,000 miles...Makes no sense.

ScottC19 New Member

ScottC19

Posted
Posted

Hey Everyone, just had this problem on my 2018 Silverado LT. I think i found the issue. If you go to the hood with it closed and push down lightly on the hood even with your finger it will have some play. Open the hood, there are 4 rubber "standoffs" i'll call them. They keep the hood a certain distance from the plastic cover on the inside. turn them to the right they go down, turn left they stick out further. I just loosened mine so the hood would stand off the truck a bit further this makes the hood engage the latch more to hold it down. I think that movement of the hood was making the sensor think the hood was open because there was no pressure against the latch from the hood. 

  • Like 1
ScottC19 New Member

ScottC19

Posted
Posted
On 2/17/2019 at 1:57 PM, Linden16 said:

Yeah its the whole late assembly correct. So i installed that and still have the same problem yup.. not sure what else could be causing it. And like i said it only rings when the trucks cold. After a few minutes of driving it stops

Hey Everyone, just had this problem on my 2018 Silverado LT. I think i found the issue. If you go to the hood with it closed and push down lightly on the hood even with your finger it will have some play. Open the hood, there are 4 rubber "standoffs" i'll call them. They keep the hood a certain distance from the plastic cover on the inside. turn them to the right they go down, turn left they stick out further. I just loosened mine so the hood would stand off the truck a bit further this makes the hood engage the latch more to hold it down. I think that movement of the hood was making the sensor think the hood was open because there was no pressure against the latch from the hood. 

Jason56 New Member

Jason56

Posted
Posted (edited)

Hey y’all just wanted to post that I tried the resistor and it worked!  I bought 2.2k ohm resistors off Amazon and soldered it in.  I was getting +\- 520 ohms with the hood open or closed so I knew it was the sensor.  Thanks for posting!

Edited by Jason56
  • Like 1
jagabom (Esquire) Enthusiast

jagabom (Esquire)

Posted
Posted
20 hours ago, Jason56 said:

Hey y’all just wanted to post that I tried the resistor and it worked!  I bought 2.2k ohm resistors off Amazon and soldered it in.  I was getting +\- 520 ohms with the hood open or closed so I knew it was the sensor.  Thanks for posting!

Can you post a link to the resister?

Thanks

Jim

gmgmgmgmgm New Member

gmgmgmgmgm

Posted
Posted

The resistance values (ohm's) stated earlier in the thread are correct, ~740 and ~2.2k ohms for opened and closed respectively. The linked 2.2k ohm resistors should work fine bypassing the switch.

 

For anyone having the issue, GM has a TSB out for this specific issue as well, regarding loose/bad grounds. If the resistance values of your hood switch are within spec. You may have a bad ground.

 

In my case it turned out to be caused by the ground braid (labled 3). Under the hood on the drivers side firewall. It is a thick braided flat steel cable bolted to the body cowl, bolt was lose an jiggled around. Throwing hood sensor codes (short to battery & open circuit). You may need to check the opposite end of the ground braid as well on the left rear cylinder head.

 

https://imgur.com/a/kddguGK

 

spacer.png

 

spacer.png

 

spacer.png

 

  • Thanks 1
  • 1 month later...
KCAudio New Member

KCAudio

Posted
Posted

I have a 2014 Sierra Denali 1500. The hood open alarm comes on when I have to much going on inside the truck, for instance if I have my AC full blast and AC seats (passenger/driver) going all at the same time the alarm will start to chime. I unplugged it before and it stopped. I was able to continue as normal. I am not to sure if it’s just the hood sensor or if the problem may go deeper, like to the BCM. Can anyone let me know if changing the sensor out would be the fix?

 

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     
    • whenindoubtuseahammer
      My First Project and GMC has me stumped

      By whenindoubtuseahammer · Posted

      Good evening. I was lucky enough to get passed down to me a 2007 GMC LBZ that was my great uncle's. While the underside and rockers are more or less gone I feel like with time I can restore it to working order since it only has 110,000 miles and he put nearly every option he could get without getting the new body style since he did not trust DEF. So far I have done everything I can think of but when I put the key into the ignition nothing happens. I put 2 brand new batteries in it. Cleaned the terminals. Check all the fuses and relays and they all pass with my multimeter. I know I'm missing something that I just cant think of. The only odd thing is the OBD2 port works which makes me think its not the mega fuse. Any advice would be greatly appreciated. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...