Jump to content

2017 Silvy Headlight Bulbs Replacement


Recommended Posts

Posted
That Lasfit looks pretty good! I took screenshots of the same part of the road you were on with each and compared them. I have one question that the video (due to quality) makes it really hard to tell.
 
It appears as though the stock HID lights might be better further down the road where the lasfit LED's dont do as good, but do significantly better up close. I paused the video's before you passed that factory looking thing on the left. The road looks like it was repaved and so there's a line, as soon as that disappeared under your hood, i paused it and took the screenshots. After comparing them and rewatching the video, it looked like i might be seeing more detail at a distance with stock vs lasfit. Can you confirm?
Not my video but I did go back and notice the same thing [emoji848]. I usually just run led on my fogs on my other vehicles and hid on my low beams. I've ran both hid and LEDs on past vehicles and prefer the hid over led

Sent from my SM-G955U using Tapatalk

  • Replies 32
  • Created
  • Last Reply
Posted
7 hours ago, xSHIFTxNASTYx said:

https://www.diodedynamics.com/replacement-oem-hid-bulbs-for-2016-2019-chevrolet-silverado-1500-pair.html

 

 

By brighter it may be meant in a way that HIDs will throw light further down the road than LEDs would in the same projector housing.

 

 

Diode Dynamics no longer sells LED headlight bulbs. According to law, halogen light bulbs can not be replaced by LED bulbs. Also, HID lights cannot be replaced by LED's either. The law states only bulbs of original type can be used in replacement and or any upgrade It;s all stated on their site now.  I know this for I put two led's from Diode Dynamics about a year ago to replace my dim stock halogen bulbs in my 2014 Sierra and they work just fine. However now if one goes bad I cannot get a replacement bulb from Diode Dynamics. So much for any warranty if needed.

Posted
20 hours ago, Ed S said:

Diode Dynamics no longer sells LED headlight bulbs. According to law, halogen light bulbs can not be replaced by LED bulbs. Also, HID lights cannot be replaced by LED's either. The law states only bulbs of original type can be used in replacement and or any upgrade It;s all stated on their site now.  I know this for I put two led's from Diode Dynamics about a year ago to replace my dim stock halogen bulbs in my 2014 Sierra and they work just fine. However now if one goes bad I cannot get a replacement bulb from Diode Dynamics. So much for any warranty if needed.

since when has a modification being illegal stopped anyone from selling it? 

that sounds kind of crazy. Thats a federal law or state? 

pretty lame of them. They cant just market it for offroad use only like every one that sells pretty much any other modification? 

Posted
30 minutes ago, Ray Capobianco said:

since when has a modification being illegal stopped anyone from selling it? 

that sounds kind of crazy. Thats a federal law or state? 

pretty lame of them. They cant just market it for offroad use only like every one that sells pretty much any other modification? 

From what I understand it's a federal law. Most people nor lighting product manufacturers knew much about it until it started being enforced lately. I think it has been a law for years. It's all stated at Diode Dynamics website. 

Posted
1 hour ago, Ray Capobianco said:

since when has a modification being illegal stopped anyone from selling it? 

that sounds kind of crazy. Thats a federal law or state? 

pretty lame of them. They cant just market it for offroad use only like every one that sells pretty much any other modification? 

No one to blame but the budding Optical Physicists.

I hope LE starts red flagging this dangerous junk and gets it off our roads.

Posted
9 hours ago, Ray Capobianco said:

since when has a modification being illegal stopped anyone from selling it? 

that sounds kind of crazy. Thats a federal law or state? 

pretty lame of them. They cant just market it for offroad use only like every one that sells pretty much any other modification? 

They still sell LED bulbs.  They just legally say they are not headlights. They advise you it’s illegal and they can only be used as fogs or off-road applications. Click any bulb Size and the lights are still there form what I’ve seen. 

Posted
10 hours ago, Fire2968 said:

They still sell LED bulbs.  They just legally say they are not headlights. They advise you it’s illegal and they can only be used as fogs or off-road applications. Click any bulb Size and the lights are still there form what I’ve seen. 

Good deal. I see that now. Glad to see that in case I need a replacement while under warranty. 

Posted
On 7/21/2020 at 10:52 AM, Ray Capobianco said:

since when has a modification being illegal stopped anyone from selling it? 

that sounds kind of crazy. Thats a federal law or state? 

pretty lame of them. They cant just market it for offroad use only like every one that sells pretty much any other modification? 

Probably so they don't get caught up in any legal battles. I'd do the same thing if it was my own company and there were laws against something like that.

 

 

On 7/21/2020 at 12:20 PM, It's Tim said:

No one to blame but the budding Optical Physicists.

I hope LE starts red flagging this dangerous junk and gets it off our roads.

Please tell me how it is dangerous? It isn't any different than any other lighting setup if properly adjusted.

Posted
19 minutes ago, xSHIFTxNASTYx said:

Probably so they don't get caught up in any legal battles. I'd do the same thing if it was my own company and there were laws against something like that.

 

 

Please tell me how it is dangerous? It isn't any different than any other lighting setup if properly adjusted.

yea but i guess thats a huge slippery slope. Thats like not being able to sell gasoline because if used improperly you burn your backyard down. 

 

i think some of the new cars these days have more obnoxious headlights even when compared to my 04 that i had the ole ghetto HID in halogen housings lol....wont do that again. 

 

anyways...it look like the 35w HIDs are the way i will eventually go. 

Posted
On 7/22/2020 at 10:45 AM, Ray Capobianco said:

yea but i guess thats a huge slippery slope. Thats like not being able to sell gasoline because if used improperly you burn your backyard down. 

 

i think some of the new cars these days have more obnoxious headlights even when compared to my 04 that i had the ole ghetto HID in halogen housings lol....wont do that again. 

 

anyways...it look like the 35w HIDs are the way i will eventually go. 

I'm thinking the same as you Ray. I'd really like to see a comparison of those 5k lumens LEDs vs the 35w HIDs though. I'm wondering if they really are that much brighter, and with LED light not traveling as far as HID light, maybe the 5k LEDs go as far or fired than the 35w HIDs and provides superior lighting up close due to the increased lumens. 

 

It shouldn't be this hard to choose :(

  • 3 weeks later...
Posted

I've decided to go with the Lasfit LED's.

 

From my research, it does appear that light from LED's does not travel as far as light from HID's, making HID's slightly more useful, however! The Lasfit LED's are much brigher than the 35w HID's that we can get, so being brighter, my assumption is that the light will travel further than the 35w HID's, or at the very least, just as far. In considering my options, there's a few other factors i've pondered in making my decision. 

 

This may not fit with others trucks, but i figure that if i'm driving in town where there's streetlights and other traffic, my headlights arent doing a whole heck of a lot anyway, so regardless of whether i use my current 25w HID's with 20% smoke vinyl wrap over the headlights, or 35w Morimoto's with the vinyl wrap, or Lasfit, its not going to make much of a difference. Where it actually matters (for me) is when im in areas without streetlights (which is pretty common where i live). I'll use my headlights, but if vision is getting tough, i added the 3 little light bars (like the special ops editions) in my grill. They are 900 lumens per light bar, so its 2700 lumens total which is more than the stock lights already. I also have a rough country bull bar with a 20 inch light bar that puts out 7200 lumens. Regardless of the distance of these lights, if im driving out somewhere and the light isn't reaching out far enough, i've got some other options at the flip of a switch that are currently so bright i cant tell the difference if my headlights are on or off (haha!).

 

I'll add this though, one of our members @fondupot uploaded the perfect video to YouTube in April comparing the 25w stock HID's, vs 35w aftermarket HID's, vs the 50w Lasfit LED's, and the Lasfit's are much brighter! Check out his video below, and follow him! He's doing some great things! His video was the deciding factor for me.

 

 

Posted
20 minutes ago, Mike_D said:

I've decided to go with the Lasfit LED's.

 

From my research, it does appear that light from LED's does not travel as far as light from HID's, making HID's slightly more useful, however! The Lasfit LED's are much brigher than the 35w HID's that we can get, so being brighter, my assumption is that the light will travel further than the 35w HID's, or at the very least, just as far. In considering my options, there's a few other factors i've pondered in making my decision. 

 

This may not fit with others trucks, but i figure that if i'm driving in town where there's streetlights and other traffic, my headlights arent doing a whole heck of a lot anyway, so regardless of whether i use my current 25w HID's with 20% smoke vinyl wrap over the headlights, or 35w Morimoto's with the vinyl wrap, or Lasfit, its not going to make much of a difference. Where it actually matters (for me) is when im in areas without streetlights (which is pretty common where i live). I'll use my headlights, but if vision is getting tough, i added the 3 little light bars (like the special ops editions) in my grill. They are 900 lumens per light bar, so its 2700 lumens total which is more than the stock lights already. I also have a rough country bull bar with a 20 inch light bar that puts out 7200 lumens. Regardless of the distance of these lights, if im driving out somewhere and the light isn't reaching out far enough, i've got some other options at the flip of a switch that are currently so bright i cant tell the difference if my headlights are on or off (haha!).

 

I'll add this though, one of our members @fondupot uploaded the perfect video to YouTube in April comparing the 25w stock HID's, vs 35w aftermarket HID's, vs the 50w Lasfit LED's, and the Lasfit's are much brighter! Check out his video below, and follow him! He's doing some great things! His video was the deciding factor for me.

 

 

Which LASFIT SET are you going with 35 watt or 50 watt ?? let us know how they work . Thanks

Posted
3 hours ago, slj2008 said:

Which LASFIT SET are you going with 35 watt or 50 watt ?? let us know how they work . Thanks

Going with the 50 watt LED's. I'll have pictures on my vehicle build page.

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • 2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...