Jump to content

Recommended Posts

Posted

My right front TPMS sensor looses signal resulting in a service tire pressure monitor message as well as the TPMS warning light coming on. My dealer has changed the right front sensor but the issue persists. The truck has gone over a thousand miles without this happening or it can happen after a few miles. It can stay on for over an hour. Looking for suggestions.

  • 3 weeks later...
Posted

Same thing happened to me yesterday on a long trip.  

had the front left go first...then came back on, then front left and right rear went out.  Came back on in a few miles...  

Posted

I'd take it back.

 

First attempt was a different sensor. 

Second attempt might be the receiving module on the truck. 

 

 

 

  • 6 months later...
Posted

I had this happen twice this year. Think a rear one and then today the front left did it. It goes away after a few miles. 

  • 4 months later...
  • 2 years later...
Posted

Any update or solution to this? I know its not the sensor, I've had the sensor changed while truck was under warranty but still same issue persists. Always same location, passenger front, also does it after tires are rotated so I know its not the sensor it's self. 

Screenshot_20240223_071834_Gallery.jpg

20240223_065905.jpg

  • 2 weeks later...
Posted
On 2/26/2024 at 8:06 PM, Gordon Lucas said:

Find the TPMS reset button, usually under the steering wheel, and hold it down until the light flashes three times. Start the car and let it run for 20 minutes to give the sensor time to reset.

dinosaur game

Is this the same as the "re-learn" procedure? If so, this gets done at every rotation and the same issue exists. Furthermore, it happens to be intermitted. Currently all sensors read fine, then the error will happen again for a day or 2 then go away??

  • 4 months later...
Posted

I don't believe my truck has this reset button under the steering wheel. Any additional info would be greatly appreciated. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • Cool to see another Vermonter!
    • I have changed oil and filter for years by starting a cold engine to warm oil up, let it run 5-10 minutes depending on temperature. Drain until it starts dripping, refill with quantity from owners manual or get it close.   
    • I changed the factory fill oil in the rear diff of my truck for the first time today and the miles is close to 9000 on the truck. There was a lot of fines on the magnet, a very thick layer but working it through my fingers it all felt like mush and as most know it appears like graphite, so no surprise chunks anyway. Certainly was time to do it from my thinking and could have been done sooner but the oil didn't look awful but sure wasn't new looking and never expected it to either. I did use some solvent to help me clean out the bottom area of the axle housing, just get any other stuff settled at the bottom washed and wiped out of the housing for the bit of effort it takes. I used Amsoil Severe Gear 75W90 in the easy packs to try out what they are like and I used up 4 packs and didn't spill much at all in the process but did take all four of the packs and go to the work bench and emptied them into a measuring container and there certainly was some in them that added up to something, then poured that into one of the easy packs and squirted in what I could get out of it. I would say the level is within 1/8th of an inch of being level with the threads at the fill plug so just the perfect amount. Once again, more than what GM says the fill volume is but computes with what others are adding to their rear diffs as well. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...