Jump to content

HELP - no power at the rear wheels 2015 Sierra 1500

bTanZ

By bTanZ
in Troubleshooting & Recalls

 Share

Recommended Posts

bTanZ Enthusiast

bTanZ

Posted
Posted

Help trouble shooting ... please!?!?

 

- While driving my approx. 100,000 mile, 2015 GMC Sierra 1500 up a paved hill, in 2-wheel drive, in the rain, with no additional payload ... I felt a mild "slip" followed moments later by a loss of power transmitted to the rear wheels ... note: there was no noticeable noise, grinding, etc. at anytime prior
- I rolled down the hill backward with the truck in neutral
- While on a flat paved surface I tried multiple positions on the gear selector, etc. and still no power at the rear wheels 
- I engaged the 4-wheel drive, power was transmitted to the front axle and wheels and I dragged it home on the front axle approx. 6-miles at 40mph and parked it

Curious to learn if theres anything electronic on the vehicle (6-speed trans., or t-case) that may have failed (since there was no mechanical noise and little warning other then the mild slip prior to failure???
I plan to try and establish where the failure is (guessing t-case or rear axle) by mechanical inspection in the coming hours/day .... any suggestions for methods ie. trans and t-case in neutral spin rear drive shaft manually and see if theres any resistance in the rear end?  Any other trouble shooting suggestions??

I tried the search and found nothing ... perhaps this is already documented somewhere you all may direct me to?

THANK YOU

bTanZ Enthusiast

bTanZ

Posted
  • Author
Posted
23 minutes ago, swathdiver said:

Well, is the rear drive shaft still attached?

yes i should have mentioned that ... the entire drive line is intact, no fluid escaped, etc..

  • Like 1
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted

Put it in park in 2wd on a hill when it starts rolling have someone look and see if the driveshaft is turning with the wheels (something in t-case) or not (something in rear axle).

  • Like 1
bTanZ Enthusiast

bTanZ

Posted
  • Author
Posted
20 minutes ago, asilverblazer said:

Put it in park in 2wd on a hill when it starts rolling have someone look and see if the driveshaft is turning with the wheels (something in t-case) or not (something in rear axle).

 

good thinking!! 

Mawz Enthusiast

Mawz

Posted
Posted
23 minutes ago, asilverblazer said:

Put it in park in 2wd on a hill when it starts rolling have someone look and see if the driveshaft is turning with the wheels (something in t-case) or not (something in rear axle).


Alternatively, put it in drive on the flats and and have some one spot to see what spins. If the driveshaft spins it's the diff and if it doesn't it's the T-case. 

bTanZ Enthusiast

bTanZ

Posted
  • Author
Posted
1 hour ago, Mawz said:


Alternatively, put it in drive on the flats and and have some one spot to see what spins. If the driveshaft spins it's the diff and if it doesn't it's the T-case. 

 

yup ...even easier!

bTanZ Enthusiast

bTanZ

Posted
  • Author
Posted

Alright so i just jumped in it in the driveway in 2-wheel drive and it drove down the driveway fine, window open and no funny noises etc. ... I went back and forth in the driveway fw/reverse and all seemed normal.
 

I took it for a lap around "the block"(i live in the woods) ... and everything operated just fine...

When it failed (and I posted this post) it it was in the rain ... is there anything in the t-case or otherwise that can disengage the rear drive shaft electronically???

bTanZ Enthusiast

bTanZ

Posted
  • Author
Posted
On 9/11/2021 at 3:35 PM, bTanZ said:

Alright so i just jumped in it in the driveway in 2-wheel drive and it drove down the driveway fine, window open and no funny noises etc. ... I went back and forth in the driveway fw/reverse and all seemed normal.
 

I took it for a lap around "the block"(i live in the woods) ... and everything operated just fine...

When it failed (and I posted this post) it it was in the rain ... is there anything in the t-case or otherwise that can disengage the rear drive shaft electronically???

 

so i did a follow on test drive and i think i have an intermittent trans. problem and the use of 4wd to get home from initial failure on the hill may have been coincidental with the intermittent problem.   this most recent test the truck is whining when it back/down shifts and my wife said she could hear it whining as I drove by her.

 

BTW trans fluid is at proper level, no funny odor and was swapped out approx 15,000miles ago

 

I'm going to try and get it to someone wit a better diagnostic tool (Snap-on, etc.) then I have to look closer at trans.

asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted

Sure sounds like something electronic acting up, I think engaging transfer case or changing gear lever position, shutting off and back on, etc. is resetting whatever electronic is misbehaving.

  • Like 1
bTanZ Enthusiast

bTanZ

Posted
  • Author
Posted

the earliest available GM dealer Transmission Diagnostics available appointment is Sept 24th ... i'm on the side lines until then :(

swathdiver Senior Enthusiast

swathdiver

Posted
Posted
1 hour ago, bTanZ said:

the earliest available GM dealer Transmission Diagnostics available appointment is Sept 24th ... i'm on the side lines until then :(

You can buy your own GM software online, the MDI with GDS software, hook it up to a laptop and diagnose and test it yourself.  You would use this tool in conjunction with the shop manual, which you can subscribe to at AllDataDIY for a nominal fee.  It will pay for itself just for this issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      It wouldn’t have happened if the government hadn’t mandated outrageous fuel mileage standards. It does very little for the consumer. It adds cost. Back during Covid there was a chip shortage. They gave a rebate for your truck if it didn’t have the chip to turn on cylinder deactivation. It was 50$ because at best you may see 1/2 a mile increase per gallon. Splitting hairs each fuel mileage trick wasn’t mandated. The government doesn’t do the engineering work and say use this until it’s already in use and they like it. The fuel mileage was mandated. And those add ons the results. There’s a mandate and they are the results.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...