Jump to content

Lifter Failure Question

NorthernX31
 Share

Recommended Posts

NorthernX31 Enthusiast

NorthernX31

Posted
Posted

I have a 2020 SLE 5.3 with roughly 75k kms on it. I've been hearing a lot about imminent lifter failure and am wondering if this is just specific to a batch of trucks or if it will likely happen to me.  I have read a few posts on here but was curious if there's anything listing how many members have had a failure and at what milage it has happened. Any info you can shed on this will be appreciated.

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Grumpy Bear
Grumpy Bear

Three reasons for a failure. 1.) Abuse. 2.) Flaw. 3.) Lubrication issue.    Is anyone going to admit to abusing their truck? Over rev. Not changing oil. Improper oil. Overloading.   

diyer2
diyer2

You have to decide how often you change oil.  Me, I like clean oil. I use Amsoil OE in our daily driver, a 2019 Hyundai Santa FE. I'm doing 4k oil changes. 

KARNUT
KARNUT

When we built a better mouse trap we got copied. When we used the better mouse trap to do better work we got costumers. That seems to be lost on GM. Changing oil every weekend isn’t possible for every

Posted Images

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Lifter failures on these trucks have been around since 2007 when AFM was put into the half tons. The chances of your truck having a failure is pretty slim given the amount of trucks out on the road. There was a small run of trucks that got bad parts a few years ago but if you're truck was part of it you would have been informed of it. Or you can contact a local dealership to see if your VIN has anything come up for a recall or bulletin.

 

 

  • Like 1
20L8TSierra24 Senior Enthusiast

20L8TSierra24

Posted
Posted (edited)

It has made it 75k miles. Seems like most fail within the first 10k if they're going to.

Edited by 20Denali22
NorthernX31 Enthusiast

NorthernX31

Posted
  • Author
Posted (edited)

What concerns me is there have been several trucks in my town that have had failures at higher mileage with some being right around the 100k km mark which in Canada is the end of the powertrain warranty. 

Edited by NorthernX31
l1tech New Member

l1tech

Posted
Posted

I've replaced lifters and cams on these with miles as low as 50k and as high as 160k. A few months back I had 2 6.2's in the shop at the same time for lifters and cam, one had ~75,000 miles and the other was pushing 120k. The funny thing is that on both of these neither had a failure on an AFM cylinder. I had a 5.7 Ram in the other day with 48,000 miles that need lifters and cam.

  • Like 1
Gangly Senior Enthusiast

Gangly

Posted
Posted (edited)
On 4/16/2023 at 10:09 AM, l1tech said:

I've replaced lifters and cams on these with miles as low as 50k and as high as 160k. A few months back I had 2 6.2's in the shop at the same time for lifters and cam, one had ~75,000 miles and the other was pushing 120k. The funny thing is that on both of these neither had a failure on an AFM cylinder. I had a 5.7 Ram in the other day with 48,000 miles that need lifters and cam.

Not trying to argue, but trying to understand the validity of this statement since all of the 6.2 from 2019 up will have DFM, not AFM, and every cylinder will be controlled by DFM.

 

Were the two 6.2's the earlier body style?

Edited by Gangly
l1tech New Member

l1tech

Posted
Posted

Both 6.2's were pre 2019 so my bad there. I have a close friend that used to work for me that is a Gm tech and he tells me that the DFM motors are experiencing the same lifter failures. AFM and DFM are realistically the same thing with the only real difference being that DFM has the ability to cancel any cylinder and AFM can only cancel 4 cylinders. Other than that you still get the same failures.

  • Like 1
  • 1 month later...
Bradley E New Member

Bradley E

Posted
Posted

My 19 AT4 just had lifter failure at 35k miles. I know this is an old thread, but just goes to show, at 4 years old, it’s only a matter of luck i guess! Fixed Bank 2 only to have others come apart on the test drive after. Gm engineer told the tech to replace the whole motor. They also mentioned inadequate oiling in these motors.

No wonder you don’t see any on the lots currently…

alrockaz Enthusiast

alrockaz

Posted
Posted

I just joined this dubious club. 2020 6.2 L87 engine with 68,000 miles. Found a good shop and they'll be replacing lifters and pushrods in both banks, along with a new cam. Going to replace the water pump and timing chain while I'm at it, since the existing parts are already being removed. He'll also be disabling DFM for me.

BossTaco2020 Enthusiast

BossTaco2020

Posted
Posted
15 hours ago, alrockaz said:

I just joined this dubious club. 2020 6.2 L87 engine with 68,000 miles. Found a good shop and they'll be replacing lifters and pushrods in both banks, along with a new cam. Going to replace the water pump and timing chain while I'm at it, since the existing parts are already being removed. He'll also be disabling DFM for me.

If you don't mind me asking, how much is that going to cost you?

alrockaz Enthusiast

alrockaz

Posted
Posted
On 6/5/2023 at 6:10 AM, BossTaco2020 said:

If you don't mind me asking, how much is that going to cost you?

$2400 for the cam, lifters and repair from that point. Add'l for the parts cost of the timing chain and water pump. Should not be any additional labor as those parts are already removed. He's not a fan of the GM water pump or timing set, so we're going with Melling. I suspect he's cheaper by several 100 than other shops, but more importantly I trust the guy. He rebuilt the transmission in my Hummer H3 as well as a few other transmissions for friends. 

  • Like 1
  • 2 weeks later...
alrockaz Enthusiast

alrockaz

Posted
Posted

Shop just got it torn down yesterday. One lifter in cylinder #7 was broken, but the other lifter in the same cylinder had a failed roller that didn't roll smoothly and had flat spots, so obviously the cam is now bad. I was replacing it anyway. Additionally, there's one bent rod so there's going to be one valve that needs replacing.

 

The book time for the project for older (2017) engines was about 21 hours; this one, the book time is 32 hours. He quoted me too low, is willing to stick to the quote, but I'll work it out with him.

 

Since he was delayed a bit, I asked him to order parts from Texas Speed for a full DFM delete. Not sure if we're going to go with LS lifters, Morel or Comp Cams, but I asked him to work it out with Texas Speed as to which are the best bet for me.

 

We looked at the valves in the heads to check out the carbon buildup that comes with these direct injection engines. Here's one valve, and this was middle of the road. Some were significantly worse, some were a bit better. He's going to disassemble the heads and clean it all up.

IMG_2807.JPG

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted
On 6/1/2023 at 8:13 PM, Bradley E said:

My 19 AT4 just had lifter failure at 35k miles. I know this is an old thread, but just goes to show, at 4 years old, it’s only a matter of luck i guess! Fixed Bank 2 only to have others come apart on the test drive after. Gm engineer told the tech to replace the whole motor. They also mentioned inadequate oiling in these motors.

No wonder you don’t see any on the lots currently…

 

Three reasons for a failure. 1.) Abuse. 2.) Flaw. 3.) Lubrication issue. 

 

Is anyone going to admit to abusing their truck? Over rev. Not changing oil. Improper oil. Overloading. 

 

@CamGTP in his post on April 3 mentioned the flaw. It happens to all makes and models. As @l1tech mentioned in his post on the 16th, this happens to non-AFM lifters as well. Heat treat is usually the culprit. Sometimes machining errors. Usually by batch. When it is the AFM lifter is can be traced to the VLOM sometimes. In high milers the lifter bore wear. Which takes it to reason #3. Lubrication. 

 

When parts touch they fail. Two things keep parts from touching. Viscosity and wear additives. Those additives are consumable and as the industry moves toward its mpg goals and oil for life goal these additives are being relied upon to do the work viscosity should be doing more and more. Sometimes when one walks to close to the edge...they fall off. When GM Engineers say "inadequate oiling' I don't think they are referring to the volume being supplied. Lifter bores don't wear out in 60K-120K if the oil is doing its job. Neither do adequately hard lifters/axles and cams. Not even in a million miles. 

 

Hands in the air, how many Ecotec3 V6's suffer this failure? It does happen. Like finding a Unicorn often. Before someone says, "But there are way more V8's"....lets normalize the statistic by saying how many per thousand units. They use the same parts from the same suppliers. Even the same oil pump. So, what's the difference? Ya all know the answer to that 🤫

 

Let's say 0W20 is actually effective. It can only be so if it STAYS a W20. One of GDI's biggest flaws is fuel diluted oil. So much so that 2.5% is considered 'normal' by everyone but a REAL Tribologist. Okay, and me :crackup:And what happens to viscosity when you dump a solvent (gasoline) in your oil? That said, not the only culprit. VII polymers are not all created equal. And pretty all of them will pass a DEXOS license test battery. Viscosity loss test have a pretty large window and many lube test services do as well before they send up the red flares. This means OCI is critical if you insist on walking the edge of the cliff. 

 

If you insist on using 0W20 then choose one at the upper end of the W20 viscosity spec and one with a 'stay in grade' VII package and one with enough antiwear to cover the silly long OCI's you believe are 'fine' and are not. Or be proactive and shorten the OCI. Don't use a UOA lab that serves up "tasty results' like Micky D. 

 

OR do what you've always done and get the results you've always got. 

 

 

 

 

 

 

 

 

 

 

  • Like 3
KARNUT Senior Enthusiast

KARNUT

Posted
Posted

When we built a better mouse trap we got copied. When we used the better mouse trap to do better work we got costumers. That seems to be lost on GM. Changing oil every weekend isn’t possible for everyone. Imagine the wait times if everyone did that. I’ll just buy the better mouse trap. 

  • Like 1
  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • garagerog
      Low fuel pressure after installing new fuel pump

      By garagerog · Posted

      Replace the fuel pump with an OEM AC-Delco.
    • Gilkey96
      Low fuel pressure after installing new fuel pump

      By Gilkey96 · Posted

      Hello, first time posting here. I have an 03 Chevy 1500HD with the 6 liter gas engine. The truck ran fine until the fuel pump died on me and had to get it towed. Replaced the fuel pump with a precision pump from O’rileys and changed the fuel filter while I was there. The truck will run and drive now but it wants to idle around 500 rpm when in drive and it tries to stall if you touch the gas. It drives fine though, just doesn’t want to idle. Put a fuel pressure gauge on the rail and only have 50 psi. I guess these trucks should have 55-62 psi to run right. I thought the regulator might be the issue because when I would unplug the vacuum hose it jumped to 56 psi. Replaced the regulator and no change. The only thing I can think of is that I was sold a faulty fuel pump. Any help would be appreciated because I’d rather not have to take the bed off again if I don’t have too. Thank you!
    • diyer2
      AFM Experience

      By diyer2 · Posted

      I've been wrenching on GM trucks for 17 years. And I need to get something off my chest because it's been weighing on me for a long time. After all that time, all those motors, all those people standing in my bay, I've figured out there are really only two kinds of owners. The ones who already know about this. And the ones who are about to find out the hard way. A guy came into my shop a few weeks back in a 2018 Silverado 5.3. Sharp guy, maybe 35. Knew his truck cold. He'd been on the forums, read the threads, done his homework. He only rolled in so I could double-check a little module he'd already plugged in himself. Wanted a second set of eyes on it. Ten minutes, in and out, drove off happy. Two days later, a completely different story walked through the same door. Older fella this time, in a 2016 Sierra. Gorgeous truck, clearly babied, not a scratch on it. Wedding ring. Looked like a guy who took care of his stuff. He was in because his engine had started knocking on the way to work. And by the time I got the valve cover off, I already knew it was too late. Lifter collapsed. Cylinder 5. Camshaft chewed up. The whole top end shot. Same kind of truck. Same motor. Same roads, probably the same dealer. The only thing separating those two men was information. I've been at this since 2008, and I've worked on everything GM puts out. Silverados. Sierras. Tahoes. Yukons. Suburbans. Escalades. The 5.3 and the 6.2. Doesn't matter which badge is on the tailgate. They all carry the same problem. So here's the information one of those guys had and the other one didn't. It's called Active Fuel Management. AFM. GM started building it into their V6s and V8s back in 2007 to squeeze out a little better mileage on the highway. Maybe a mile or two a gallon. All to hit government fuel economy numbers. The way it works, the motor quietly shuts down half its cylinders when you're just cruising along. And the little lifters that pull that off have a tiny pin inside them that's constantly clicking in and out. Lock, unlock, lock, unlock. Hundreds of times a drive. Thousands of times a week. Eventually one of those pins wears through. The lifter drops. And it starts grinding the camshaft down like a chisel on butter. And what nobody tells you is that the shudder you feel around 40 or 50 mph? That's the system cycling. Every single time. Here's what really gets me. The pre-2007 trucks, the ones without AFM, they're bulletproof. I've got customers still daily driving them with 260,000 miles on the odometer. Not a problem in the world. GM took a perfectly good motor that would have lasted a lifetime and bolted this system onto it. And it is wrecking engines that should have run forever. The guys who hang around the forums already know all of this. So do the techs. They handled this years ago. They didn't sit around waiting for the dealership to mail them a warning letter, because that letter is never coming. It's the guys who figured somebody would've told them who end up on my lift. And I want to be clear, because this part matters. Maintenance has nothing to do with it. I've torn down motors with barely 30,000 miles on the clock. I pulled apart a Tahoe last summer with 24,000 on it. Practically a brand new truck. Owner had it less than a year. Spotless oil. Best synthetic money can buy, changed early every time. Made no difference. I've seen guys with full dealer records, every interval stamped. Made no difference. The oil changes were never the problem. The pin was. And no amount of babying that truck stops that pin from cycling every single time you drive. That's the part that eats at me. These are good motors. Take the AFM out of the equation and a 5.3 or a 6.2 will run 300,000 miles and never blink. So a few years ago I started telling every single owner who comes through my doors the exact same thing the smart guys already knew. Get yourself a FullForce disabler. It plugs right into the port under your dash. Couple of seconds and you're done. It just tells the computer to leave every cylinder running, full time. No more cycling. No more beating those lifters back and forth every time you turn the key. It doesn't reprogram anything. Doesn't touch your tune. And unplug it before a dealer visit and there's absolutely zero trace it was ever installed. I've had customers come back at 40,000, 60,000, 80,000 miles after I put one in. Zero issues. The trucks run smoother. And the lifters aren't getting beaten to death every single drive. I won't sit here and tell you it's magic. A lifter that's already damaged is a lifter that's already damaged, and this won't un-ring that bell. But it takes away the one thing causing all that wear in the first place. That's the whole game. You don't need a five-thousand-dollar delete. You don't need an expensive tune. You don't need to tear anything apart. You just need to stop the cycling. I'm not writing this for any company. I'm writing it because I'm tired of watching the guys who didn't know pay four and five figures for it. I'm tired of being the guy who has to break the news. I'm tired of knowing that the guys who did know fixed the whole thing for the price of a tank of gas, and the only difference was that somebody told them first. If you drive a Silverado, Sierra, Tahoe, Yukon, Suburban, or Escalade from 2007 or newer with a V6 or V8, you've got AFM. You've got those lifters, and they're cycling every single time you drive. So be the guy who already knew. Not the one I'm scraping metal out of next month. EDIT: A bunch of folks asked, so here it is. The one I put my faith in is FullForce. This is where to find it: https://www.tryfullforce.com/products/fullforce™-afm-dfm-disabler They back it with a 60-day guarantee too. I've handed out more than I can count and not one's ever come back to me. Not one. See less
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Thanks for following along. I'm not author material, my tenses are all over the place and an editor would have a heck of a time cleaning up after me. Reading and writing is still a fun pastime though.   My new scanner came in yesterday, wow, where the heck has this thing been?! It connects right up to the Blazer, there's all kinds of bidirectional tests like EGR activation and percentage, toggle the fuel pump relay, EVAP purge valve, IAC control, AC relay, reset the transmission's adaptive learning, toggle shift solenoids and TCC lockup, and I can reset fuel trims with the click of a button...all things I could have used over the last 60 days!   It's also telling me there is a stored code in the ABS module for front left wheel sensor open and something about the brake switch. The ABS dash light works. It illuminates normally during the self-test at key on/ start and that's it. I cleared the codes and will see if they set when I take it out later. That, and I'm going to get (hopefully) real data on timing and cam ******. The PID's are there.   I connected the tool to my truck...holy smokes. Newer vehicles make early OBDII vehicles look like 8-bit, pixelated, early Nintendo stuff. This? This is like wearing 3D virtual reality goggles playing one of those elaborate, cinematic video games with seasons and plots in comparison. There are SO MANY modules and SO MANY tests and SO MUCH data. There's a scanner sequence for filling the coolant...   End of the day, it's a tool with way more power than I need, but the versatility to do old and new is there (and I need an adapter to connect it to my OBDI Camaro). It will allow me to do the first pass of diagnosis when out-of-warranty vehicles need help, and it will enable more DIY maintenance like brake system bleeding, ABS bleed, etc. I probably over-bought here, but, mission is accomplished.   Enjoy your Sunday...I need to shut this machine down and go get ready for the week ahead.
    • MORSNO
      Which 2027 engine will you choose?

      By MORSNO · Posted

      Not that I've read, after all the issues they've had in the past I'm pretty sure they learned their lesson. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...